Good for occasional machining, economy kits contain lower-strength components than standard kits.

The stepped end provides support and quick height adjustment when paired with a step block.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

Use these blocks to support setup clamps. Fit the nonslip steps together for quick height adjustments.

The offset shape provides more clearance above the nut than standard clamps. Also known as gooseneck clamps.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

Also known as toe clamps, these grip the side of a workpiece to leave the top free for machining.

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

Mount using the holes in the base.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Push the lever to lock the handle and prevent accidental opening.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

Mount these clamps below a surface.

The mounting base secures these clamps to a rail or bar.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

Replace worn screws or customize your clamps.

These clamps have mounting holes on the bottom.

Mount the base to a work surface using screws.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Hold workpieces of different thicknesses without adjustment.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

Secure your workpiece from the side by fully extending the plunger, and push a lever to lock the handle in place.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Push the lever to lock the handle and prevent accidental opening.

The plunger can be locked at any position along its travel.

Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.

These clamps have twice the capacity of standard C‐clamps.

Lighter weight than other metal clamps, these are less likely to bend thin material.

A bright finish makes these clamps easy to see.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

With no handle or protruding screw, these clamps can fit into tight spaces.

Apply pressure to the side of a workpiece as well as the top and bottom.

The jaws move in unison to apply even pressure and prevent twisting.

When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.