We will reply to your message within an hour.
Join pieces of conduit.
Attach conduit to a knockout in an outlet box or enclosure.
Join different sizes of conduit.
Ground conduit by running a ground wire through the attached lug.
Reduce the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.
Seal out moisture while reducing the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.
Also known as intermediate metallic conduit (IMC), this is lighter in weight than thick-wall (rigid) steel conduit, yet it has the same strength.
This impact- and crush-resistant conduit is also known as galvanized rigid conduit (GRC).
This nonmagnetic aluminum conduit withstands damp and corrosive environments.
Connect different sizes of conduit.
Use in food-processing and chemical plants—this is the most corrosion resistant thick-wall conduit we offer.
Also known as conduit bodies, these ports provide access to wire and cable inside thick-wall (rigid) metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.
Also known as electrical metallic tubing (EMT), this conduit has thin walls that easily bend with a conduit bender and can be cut with a hacksaw.
The most corrosion-resistant thin-wall conduit we offer, use this along walls and ceilings in food-processing and chemical plants.
Visually identify different runs of wire and cable along walls and ceilings with this conduit that has a painted exterior.
Also known as conduit bodies, these ports provide access to wire and cable inside metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.
Create a connection point to route overhead service wire and cable from utility poles to electrical meters, bringing power to buildings.
These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.
When used with liquid-tight fittings, this conduit seals out liquid. The steel core provides crush resistance, and the cover is UV light resistant.
Even in temperatures as low as -50° F and as high as 220° F, this conduit stays flexible.
In addition to resisting oil, this conduit resists lubricants and grease.
Run conduit in food areas—the cover can be cleaned and sterilized without weakening or splitting. This conduit meets NSF/ANSI standard 169 for special-purpose food equipment.
The toughest liquid-tight flexible metal conduit we offer, this resists oil, chemicals, and extreme temperature fluctuations.
Also known as FMC, this conduit offers the crush resistance of metal combined with flexibility to handle bends in tight spaces.
Attach conduit and armored cable to a knockout in an outlet box or enclosure.
Protect fiber optic cable with this small-diameter conduit.
These adapters provide electromagnetic interference (EMI) protection when connecting shielded flexible plastic conduit to a knockout in an outlet box or enclosure.
Secure threaded metal conduit fittings to a knockout in an outlet box or enclosure.
These fittings seal out liquid when used with continuous-flex liquid-tight plastic conduit.
Transition between conduit sizes and types.
Transition between types of conduit.
Route power, data, and control cable rated up to 600 volts AC/DC.
This raceway system is also known as wireway and wire trough.
Gaskets on the covers and at connection points protect against dust as well as seeping oil and coolant.
In areas exposed to washdowns, chemicals, and corrosion, install this stainless steel raceway system that has gaskets at the connection points.
With a top that overhangs the cover, this raceway keeps out rain. It is rated NEMA 3R for protection from liquids and light splashing.
Protect wire and cable from dust, dirt, and oil/coolant dripping—this raceway is rated NEMA 12.
These cable ramps are strong enough to withstand equipment traffic.
With the widest channels of any of our cable ramps, these ramps can span large cable, hose, and pipe.
This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.
The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.
This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.
Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
Protect wire and cable from signal distortion caused by nearby equipment and devices. Expandable, this sleeving stretches to fit over items for easy installation, then tightens around its contents for a secure fit.
Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.
Insulate your wire, cable, and hose in continuous temperatures up to 400° F and easily access them. This sleeving opens anywhere along its length with a hook-and-loop strip.
Adapt metric, NPT, and PG conduit and cord grip threads to match knockout threads.
The zinc plating on these tray systems offers good corrosion resistance.
These are the most corrosion-resistant tray systems we offer.
Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.
Create a system to route cable and hose by connecting components such as straight trays and tees.
A more durable construction with a zinc-plated steel frame provides strength for a longer service life than other open cable and hose carriers.
Use these accessories to mount carriers to your machinery without creating an obstruction.
Route pipe, tubing, and conduit across strut channel.
For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.
Hold pipe, tubing, and conduit away from strut channel.
Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.
Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.
For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.
Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.
Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.
For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.
A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.
Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.
Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.
A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.
A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.
These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.
Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.
Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.
These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.
Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.
Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
For a strong, secure connection, mount these hangers by welding them to a rod.
Cut as much strap as you need to hang duct, pipe, and other materials.
Use these close-fitting hangers for a more rigid hold around material than when using straps alone.
Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.
A mounting plate provides a more secure hold at the mounting surface.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
Suspend and route flat-bottomed objects such as strut channel and small duct.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.
These clamps have a fixed hanger for rigid connections.
Clamp onto metal tubes such as pipe, scaffolding, and railing to hang lighting fixtures, threaded rod, and equipment.
Wire, cable, and cords pass through the grommet opening while the bristles fill in the gaps to control dust and debris. Use these grommets to eliminate cord clutter on desktops, countertops, benchtops, and other work surfaces.
Eliminate clutter on desktops, countertops, benchtops, and other work surfaces by organizing wire, cable, and cords.
Kits include grommets, a cutting punch, a cutting block, an installation punch, and a die set. Use them to create a way to run rope and cable through tarps, covers, and curtains.
The extended neck on the washer of these grommets adds reinforcement so you can use them in thicker material such as woven fabrics. Press them into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.
A rolled rim provides added grip while the elongated neck and teeth on the washer, also known as a spur washer, add reinforcement and reduce rotation so you can use these grommets in thick materials such as canvas. Press the grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.
Press these grommets into a hole you've already cut. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.
The sharp neck on these grommets cuts the material as you press them into place, eliminating the need for a cutting punch. They strengthen and prevent holes from fraying in tarps, covers, and curtains. They also provide a way to run rope and cable through your material.
Support and protect conduit by mounting it to strut channel.
For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.
These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.
The insulation resists corrosive chemicals and salt water, and the wires in this cable are tin plated for corrosion resistance.
Create a permanent outlet system without opening walls. These outlet strips mount to a wall with clips and hardwire to an existing electrical system.
Follow the easy-to-read markings to bend conduit to the angle you need.
When you're working with exposed conduit, these benders make offset bends so your conduit matches knockout holes in electrical boxes.
Choose these benders for short‐radius conduit bending.
Powerful enough to bend conduit and pipe to the angle you need, these are for use on Schedule 40 pipe.
Make on-the-fly bends in Schedule 40 PVC conduit and pipe without the risk of kinks or cracks. Lightweight and flexible, these benders are easy to keep on hand for occasional use and last-minute adjustments.
Bend more than one size of tubing without adjusting the bending head.