With a smooth, shatterproof lens, these lights have no crevices where debris can accumulate. Their stainless steel connectors, plastic lens, and mounts resist acids, alkalis, and other chemicals commonly used in food environment washdowns.

Know your machine’s status at a glance—green for running, red for stopped, yellow for standby. Using your programmable logic controller (PLC), you can adjust the brightness of these lights and mix red, green, and blue light to achieve thousands of colors.

Similar in function to tubular machine lights, except strip machine lights have a flat lens that directs light downward.

Illuminate machines or monitor processes in areas where flammable or combustible gases may be present, such as during leaks or ventilation failures. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

With a slimmer profile than other strip machine lights, these lights fit in tight spots inside machinery because they don’t have a circuit board.

Brighten countertops that your ceiling lights can’t reach. These lights are low-profile, so they won’t take up valuable workspace below your cabinets.

These thin, flexible lights wrap around equipment, hide under cabinets, and squeeze into tight spaces—all you need is an outlet. Just peel and stick to attach them to any smooth surface.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

These lights cast a narrow beam of light. With a gooseneck arm, they are faster and easier to reposition than articulating-arm lights.

Light up your workspace when overhead lighting falls short.

Stretch the arm to bring light directly over your work—even across a large surface. Also known as articulating arm lights, these lights have rigid sections that hold their position steady, including when fully extended.

Though not as bright as our miniature fiber-optic lights, these lights are more affordable. With flexible arms, you can adjust these lights to direct light where you need it, even in hard-to-reach spots.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

A mounting clip at the base lets you attach these lights to nearby surfaces.

Keep excess cords out of your way—the reel locks the cord at any length and retracts it when not in use.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Light up damp areas—these lights seal out moisture and humidity. They’ll even work in areas with frequent washdowns. Rated NEMA 4X, they withstand spraying liquid, resist corrosion, and keep out dust.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Brighten remote areas using the same battery as your other cordless Milwaukee tools.

With a rounded, weighted base, these floodlights wobble—but don't fall over—when bumped.

Bring light to remote, wet areas. These floodlights are IP rated to handle humidity and dripping, splashing, and falling liquids. Adjust their tripod up and down to direct light as far as you need.

Brighten areas of a jobsite with these floodlights, and move them at a moment’s notice.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Brighten enclosures and small spaces like closets and drawers—no hardwiring or outlets needed. Powered by a rechargeable battery, these lights are easy to install and help save on maintenance costs.

No bigger than a roll of tape, these lights fit inside equipment to provide visibility during tool changeovers and maintenance.

The most versatile of our machine vision lights, these bar lights can be used alone, installed side-by-side, or assembled into a ring light.

Surround your camera with light for perfectly aligned brightness. These small and lightweight ring lights are mounted directly around your machine vision camera or vision sensor.

Flood bright, even light on parts so your machine vision camera can capture a detailed image for inspection.