These grips have an extension that provides extra support for moving cables and prevents kinking for longer cable life. Grips are rated IP68 and 69K for protection from continuous submersion and high-pressure, high-temperature jets of water. They are also rated NEMA 4X, 6, and 12 for indoor and outdoor protection against corrosion, water projected from a hose, and dripping oils and lubricants. A rubber bushing and O-ring create a tight seal to prevent liquid from entering the connection.

For technical drawings and 3-D models, click on a part number.

These grips have an extension that provides extra support for moving cables and prevents kinking for longer cable life. Grips are rated IP68 and 69K for protection from continuous submersion and high-pressure, high-temperature jets of water. They are also rated NEMA 4X, 6, and 12 for indoor and outdoor protection against corrosion, water projected from a hose, and dripping oils and lubricants. A rubber bushing and O-ring create a tight seal to prevent liquid from entering the connection.

For technical drawings and 3-D models, click on a part number.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life. They’re good for cords used on handheld equipment. Made of polyamide, they stand up to corrosion and wear.

For technical drawings and 3-D models, click on a part number.

Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure. They’re rated IP68 and NEMA 6P, so they withstand use under water and protect electronics inside enclosures from moisture and harsh chemicals. All are made of nylon, making them corrosion and wear resistant. They relieve the strain on a cable when its pulled, extending the life of the cable.

When choosing a size, keep in mind that the sealing nut ID and body ID must be large enough for the end of your cord to fit through with the connector.

For technical drawings and 3-D models, click on a part number.

Able to resist most chemicals and withstand use underwater, these nylon grips are rated IP68 and 69K for protection from continuous submersion and high-pressure, high-temperature jets of water. They are also rated NEMA 4X, 6, and 12 for indoor and outdoor protection against corrosion, water projected from a hose, and dripping oils and lubricants. A rubber bushing and O-ring create a tight seal to prevent liquid from entering the connection. All meet UL 746C f1, so they’re UV resistant and can be used in direct sunlight, as well as UL 94 V-0, which means they’ll self-extinguish within 10 seconds of catching fire and won’t spread flames by dripping. UL listed and CSA certified, they meet U.S. and Canadian safety standards.

Metric Threads are also VDE certified, meaning they meet European safety standards.

For technical drawings and 3-D models, click on a part number.

Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment. With a continuous-flex extension that prevents kinks and stress, these grips securely hold cable and prolong cable life. Snap-in tabs secure the cord grips without the need for locknuts or tools. IP68 rated, these cord grips withstand dust and temporary submersion. They are made from polyamide, so they also resist corrosion and wear.

Press the removal tool (sold separately) to the back of the cord grips to unlock the snap-in tabs.

For technical drawings and 3-D models, click on a part number.

Snap these cord grips into place to secure cable in wet environments. Unlike most cord grips that require locknuts for installation, these remain secure without hardware or tools. They are IP68 rated for protection from dust and temporary submersion. Made from polyamide, these cord grips resist corrosion and wear.

Press the removal tool (sold separately) to the back of the cord grips to unlock the snap-in tabs.

For technical drawings and 3-D models, click on a part number.

Tighten the screw-down clamp on these grips for superior pull-out resistance while relieving tension at connection points. Grips are rated IP68 for protection from prolonged submersion and IP69K for protection against high-pressure, high-temperature jets of water. A rubber bushing and O-ring create a tight seal to prevent liquid from entering the connection.

For technical drawings and 3-D models, click on a part number.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation. Vents on these cord grips equalize pressure between the inside and outside of an enclosure, preventing harmful moisture from forming. They are nickel-plated brass, so they resist corrosion. These cord grips are rated IP66 and IP67 for protection from dust, washdown, and temporary submersion.

For technical drawings and 3-D models, click on a part number.

These cord grips are lightweight yet durable. As you tighten the grip, a nylon inner ring and lubricated rubber bushing secure your cable, prevent overtightening, and create a seal around the cord to block out liquid. The inner rings are colored by size so you can identify them at a glance.

Locknut and O-ring kits (sold separately) create liquid-tight seals between cord grips and enclosure knockouts. When used together with the cord grips, they meet NEMA 4X, NEMA 13, and IP66 ratings, so they can be used indoors and outdoors to protect against corrosion, dust, spraying water, oil, and coolant. Each kit includes two locknuts and one or two O-rings.

For technical drawings and 3-D models, click on a part number.

Attach a cord grip to cable without removing connectors and rewiring. These cord grips have a two-piece design to fit around cables with connectors. Choose a housing and then select inserts (sold separately). Inserts have a slit, eliminating the need to thread cable through them.

For technical drawings and 3-D models, click on a part number.

Tabs on one end snap into grooves in conduit; the other end attaches to a knockout in an outlet box or enclosure. These adapters help seal out air and liquid when used with flexible plastic conduit. All meet IP68 for prolonged submersion and IP69K for high-pressure, high-temperature washdowns. They withstand vibration, are flame retardant, and resist oil, solvents, and UV light.

For technical drawings and 3-D models, click on a part number.

These adapters provide electromagnetic interference (EMI) protection when connecting shielded flexible plastic conduit to a knockout in an outlet box or enclosure. Twist the compression end over the conduit; tighten the compression ring to secure.

A brass locknut is required (not included) when installing in an unthreaded knockout.

For technical drawings and 3-D models, click on a part number.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment. Their poles and keyways adhere to standard coding layouts, reducing the chance you’ll mismatch connectors.

A- and C-coded connectors send both power and signal, while K-, L-, S-, and T-coded connectors only send power. Choose A-coded connectors for AC and DC sensors, actuators, motors, light curtains, and other devices. They’re often used to connect equipment to IO Link controllers and within Profibus, DeviceNet, and other fieldbus systems. C-coded connectors are often used with AC sensors and actuators.

Receptacles thread into panels and walls, making them best for stationary or permanent installations such as control panels. IP67 and IP68 rated connectors can withstand brief submersion. Add caps to protect connectors and maintain their IP and NEMA ratings when not in use.

Note: Sockets and female receptacles may have extra holes on their face that are not used.

For technical drawings and 3-D models, click on a part number.