Often used in large, open workspaces, these switches can be wired on opposite ends of the room to control the brightness of lights on the same circuit. They're also known as three-way switches and work in pairs to control lights from two different locations. The actuator to turn lights on and off is separate from the dimmer to maintain a desired lighting level. They fit standard wall plates (not included).

Push and release the button to activate—no electricity required.

Pull the chain to send a switch signal. These switches are commonly used as replacements in lights and fans.

For technical drawings and 3-D models, click on a part number.

Immediately cut power with a single push. These switches meet EN 418 for compliance with European machine directives for emergency stop applications. All have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. They include enough contact blocks to control the number of circuits listed.

Pull reset, illuminated pull reset, and turn reset switches are rated NEMA 4, 13, and IP66. Contact blocks for these switches are rated IP20.

Note: Illuminated switches include a bulb. If wiring the switch and the bulb to the same circuit, the circuit voltage must not exceed bulb voltage.

Pull reset switches with lockout latch when you depress the button, and can be locked in that position using a padlock with a max. 3/16" shackle diameter. Switches are rated NEMA 13 and IP65.

For technical drawings and 3-D models, click on a part number.

Immediately cut power with a single push. These switches meet EN 418 for compliance with European machine directives for emergency stop applications. All have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. They're rated IP66, IP69K, NEMA 3S, NEMA 4X, and NEMA 13, and are UL and C-UL Recognized Components. Switches include enough contact blocks to control the number of circuits listed. Contact blocks are rated IP20 and are UL and C-UL Listed.

Key reset switches are keyed alike, so if you buy multiple switches they will all reset with the same key.

Additional contact blocks (sold separately) can be added to control more circuits, or replace the included contact block.

For technical drawings and 3-D models, click on a part number.

A single-piece construction prevents the contact block from separating from the actuator in high-vibration applications. These switches immediately cut power with a single push. They have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. These switches meet American, Canadian, European, and other global safety requirements. They’re rated NEMA 4X, NEMA 13, and IP65 for protection from corrosion, washdowns, and oil/coolant spraying.

Note: Illuminated switches include a bulb. If wiring the switch and the bulb to the same circuit, the circuit voltage must not exceed bulb voltage.

For technical drawings and 3-D models, click on a part number.

Switches immediately cut power with a single push. Use these switches where ignitable gas and dust may be present. Their contact blocks are explosion proof and UL listed for Class I, Division 2, Groups B, C, and D hazardous locations. All are rated NEMA 4X and IP65 for protection from corrosion and washdowns. They include enough contact blocks to control the number of circuits listed.

Additional contact blocks (sold separately) can be added to control more circuits, or replace the included contact block.

For technical drawings and 3-D models, click on a part number.

Immediately cut power with a single push. These switches are rated for protection from low-pressure streams of water and oil/coolant spraying. They have positive force contacts that will open a circuit when actuated even if a spring fails or the contacts stick. Switches include enough contact blocks to control the number of circuits listed.

Turn twist switches back on by twisting the button and pull switches by pulling it. Add an optional lockout on either kind to cover the button and prevent changes its position.

Switches with lockout latch when you depress the button, and can be locked in that position using a lockout or padlock with a 9/32" shackle diameter.

Note: Illuminated switches include a bulb. If wiring the switch and the bulb to the same circuit, the circuit voltage must not exceed bulb voltage.

Additional contact blocks (sold separately) can be added to control more circuits, or to replace the included contact block.

Immediately cut power with a single push. The large palm-sized buttons on these switches provide an easy target, so they're easy to use even while wearing gloves. When the button is depressed, the switch latches and can be locked in that position using a lockout or padlock with a 9/32” shackle diameter (not included). All have positive force contacts that will open the circuit when actuated even if a spring fails or the contacts stick. They're rated NEMA 13 and IP65 for protection from oil/coolant spraying and washdowns.

For technical drawings and 3-D models, click on a part number.

Activate or deactivate fans, lights, and other devices inside your enclosure when you open or close the door. To actuate these switches, push the plunger. They work with most enclosures, since you can slide the housing up to 1 3/8” to make the switch longer or shorter. Mount screws anywhere along the mounting slots to install.

Normally open and normally closed switches control two devices at the same time—for example, use them to turn a light on and a fan off when you open the door.

For technical drawings and 3-D models, click on a part number.

Immediately cut power by pulling a cable. These switches are often used to turn off production lines and material handling systems in an emergency. All have positive-force, snap-open contacts that open a circuit when actuated, even if a spring fails or the contacts stick. The contacts will remain open until you tension the cable and reset the switch.

Two-direction switches can be used with tension springs (not included) to open contacts and stop machinery if the cable breaks.

Accessory kits (sold separately) simplify the installation of a new switch.

For technical drawings and 3-D models, click on a part number.

Safe to use near ignitable gases and dust, the housing on these switches seals in anything that could ignite flammable material. All are UL listed and CSA certified for use in hazardous locations. Yank the cable anywhere along your line to quickly cut power in emergencies. They have positive-force, snap-open contacts that open a circuit when actuated, even if a spring fails or the contacts stick. The contacts will remain open until you tension the cable and reset the switch. Use the tension indicator to visually confirm that they’re reset correctly.

For technical drawings and 3-D models, click on a part number.

Prevent accidental actuation from bumps—these switches require you to grip and twist the lever to turn the switch. The contact block and actuator are all one piece, so they won’t separate in high-vibration applications. Install them in a standard panel cutout.

For technical drawings and 3-D models, click on a part number.

Replace the hinges on access doors or machine guards with these switches to keep your team safe from active machinery. Also known as interlock switches, they automatically shut off power to your machinery when the door or guard opens. They can be mounted on flat frames or aluminum T-slotted framing. These switches have positive-force, normally-closed contacts that will open a circuit when the switch is actuated, even if a spring fails or the contacts stick. They’re rated IP65 for protection from washdowns.

Also known as interlock switches, these ensure the safety of personnel by automatically shutting off power to machinery when an access door opens. Mount the switch to the door frame and mount a key to the door so that the key is inserted into the switch when the door is closed. When the door opens, the key is removed from the switch and the machine shuts down. They’re often used with machine guards.

Style A-F have positive-force, normally closed contacts that will open a circuit when the switch is actuated even if a spring fails or the contacts stick.

NEMA 6 rated switches protect against temporary submersion and washdowns.

NEMA 4 rated switches protect against washdowns.

IP67 rated switches protect against temporary submersion.

Flexible keys (sold separately) pivot 15° to make it easier to align with the switch during installation.

For technical drawings and 3-D models, click on a part number.

Cut power and keep it isolated to prevent equipment from starting up during inspection and maintenance. These switches are housed in a protective enclosure that resists denting, chipping, and cracking. Mount them to the wall when you run out of space in an electrical panel.

Switches with lockout secure in the off position with a padlock with a maximum shackle diameter of 5/16” (not included).

Photovoltaic switches can be used with photovoltaic cells which convert sunlight into electricity.

For technical drawings and 3-D models, click on a part number.