Unlike other stainless steel fittings, these are made in the U.S.A. for superior quality. As another marker of quality, they come with a certificate with a traceable lot number and test report that guarantees material composition.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

Use these fittings in extreme-pressure conditions up to 15,000 psi.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.

Also known as Schedule 10 fittings, these are thin, lightweight, and corrosion resistant.

One end of these fittings has clockwise (right-hand) threads and the other has counterclockwise (left-hand) threads. Their galvanized finish gives them fair corrosion resistance.

The threads on these fittings have clockwise (right-hand) threads on one end and counterclockwise (left-hand) threads on the other end.

Use these unions to connect different metals in a piping or plumbing system. They have a gasket with a plastic sleeve that inhibits destructive corrosion.

For use in noncorrosive environments, these fittings have better strength than our low-pressure iron and steel pipe fittings.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

Also known as no-hub pipe fittings and soil pipe fittings, these fittings are for use in gravity-flow applications both above and below ground.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

With thicker, stronger walls than our standard-wall butt-weld pipe fittings, these fittings stand up to your high strength applications.

Use these heavy-duty brass fittings for high-pressure drinking water applications.

Not only do these brass fittings have the strength to handle high-pressure applications, the male threads have a sealant applied for extra protection against leaks.

Choose these fittings when you need better strength than our low-pressure brass and bronze pipe fittings.

When space in your pipe line is limited, choose these miniature fittings that are one inch or less in length.

Less than an inch in length, these miniature fittings work well in low-pressure pipe lines that are tight on space.

When you're unsure of the exact thread type you need, these fittings have universal threads that are compatible with the most common ones (NPT, NPTF, BSPP, BSPT).

Extreme pressures are no problem for these heavy-duty brass fittings.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Designed for medium-pressure applications, these fittings have better strength than our low-pressure aluminum pipe fittings.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.

These fittings have excellent resistance to stress cracking and have better corrosion resistance than most stainless steel alloys.

Watch water flow through your line. These fittings are compatible with Schedule 40 pipe, the industry standard for residential and commercial low-pressure plumbing and water supply.

Use for pressures up to 200 psi. Also known as insert fittings, these slide into semi-flexible plastic pipe and secure with a clamp.

Connect to CPVC pipe for use in high-temperature plumbing and water supply applications.

These Schedule 40 fittings are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

With thinner walls than Schedule 40 fittings, these are lighter in weight and have more space on the inside for high-flow applications, such as underground gravity-flow sewer and storm drainage lines. They are also known as SDR 35 fittings.

Also known as Victaulic fittings, these have grooved ends that connect to pipe with a clamp, so you can access your chemical process line for routine maintenance. Fittings have excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances.

The inside of these fittings won’t leach contaminants into your line or accumulate particles—they’re polished to an ultra-smooth 12 Ra finish, which also makes them easy to clean. Made of polypropylene, they resist organic solvents, acids, and alkalis better than CPVC fittings.

Made of PVDF that’s finished to a 12 Ra smoothness, these fittings handle some of the harshest chemicals without leaching contaminants into your line. Comparable to Kynar, they handle most organic solvents that would dissolve CPVC, and chlorine or nitric acid that would weaken polypropylene.

These PVDF fittings meet UL 94 V-0 for flame retardance, so they delay the spread of flames to valuable equipment. PVDF is comparable to Kynar, and has the chemical resistance to stand up to solvents and other harsh substances.

Use these clamps to connect easy-access UV-resistant polypropylene pipe fittings to pipe. The clamp-together design allows you to access your line for routine maintenance.

Made of polypropylene, these gravity-flow fittings withstand organic solvents, such as acetone, that would dissolve CPVC pipe. They also stand up to highly corrosive acids, such as hydrochloric acid, and alkalies.

These fittings are NSF certified for use in corrosive waste gravity-flow systems. Made of CPVC, they have better chemical resistance than ABS plastic gravity-flow fittings and can stand up to highly-corrosive acids and other harsh substances.

Create a leak-free, durable connection in plastic tanks, walls, or panels without gaskets or sealants.

Made of PVDF, also known as Kynar, these fittings stand up to the harsh chemicals used to clean food processing lines. Unlike other plastic fittings, such as nylon and acetal fittings, they’ll resist degrading when exposed to strong alkali and highly acidic solutions.

These all-metal expansion joints can handle high temperatures up to 800° F.

The EPDM lining in these joints meets NSF/ANSI 61 standard for use with drinking water.

Slip these joints over your pipe ends and tighten the band clamps for a secure hold.

These joints weld to unthreaded pipe or another butt-weld fitting for a leak-resistant permanent connection.

Connect two pipes that are up to 100 feet apart—cut the connector to the length you need and attach a clamp to each end.

These connectors are for use in low-pressure air and vacuum conveying systems, as well as in gravity-flow systems.

With an FEP sleeve and PTFE sealing tape, these connectors withstand chemicals better than rubber connectors. Use them for joining low-pressure chemical waste drainpipe and fittings or transitioning between different chemical piping.

Use in high-pressure applications up to 500 psi.

These junction blocks have threaded holes that allow air or fluid to flow at a 90° angle through the block. Use them to organize and separate multiple lines in your system.

Polished to a 20 Ra finish, these fittings have an extra-smooth interior that prevents product buildup and inhibits bacteria growth.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

Use at pressures up to 4,300 psi.

An alternative to bolt-together fittings, these handle larger tube OD sizes and have higher vacuum ratings than quick-clamp fittings. Also known as ISO-K high-vacuum fittings, the clamps have claws that grab hold of fittings with flanged ends.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Polished to at least a 15 Ra finish on the inside, these fittings have an ultra-smooth interior surface that helps prevent contamination. They are also known as ultra-high-purity fittings.

Transfer liquids and gasses into high-vacuum chambers with these assembled fittings, also known as feedthroughs.

Twist these fittings onto high-vacuum tubing to quickly make sealed, high-vacuum connections without the need for clamping, welding, or tools.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

When cleanliness is crucial to your application, choose these fittings that are individually cleaned and bagged to prevent contamination.

These fittings include a nut with a built-in sleeve, so there’s no need to remove the nut for assembly.

The sleeve in these fittings is rubber instead of metal, so it cushions the tubing and absorbs vibration while creating a tight seal.

Use these fittings to make leak-resistant connections without threading or soldering. Slide them over tubing and turn the end nuts to compress the gasket.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Made of plastic, these fittings are lightweight compared to our brass push-to-connect fittings.

The flared end of the fitting nests inside the fitting body, providing extra support to the tubing. Fittings are also known as inverted 45° flared fittings.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

Barbs grip onto tubing.

Barbs grip onto tubing.

The nickel plating on these fittings provides better corrosion resistance than unplated brass fittings.

Color-code fittings for easy identification. These aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

Made of stainless steel, these fittings have better corrosion resistance than brass fittings.