We will reply to your message within an hour.
More
Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.
These clamps rotate and pivot to ensure the rod hangs straight, even on sloped beams.
Also known as purlin clamps, these clamps are shaped to fit around beams that have a 45° or 90° lip.
A toothed clip secures these clamps to the beam—no fasteners required.
For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.
Add a crossbeam for hanging lifting equipment, creating overhead conveyor systems, and supporting structural applications.
Join two beams in a straight line.
A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.
Clamp to both sides of a beam to add an anchor point for hoists and other overhead equipment.
Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.
These clamps have a fixed hanger for rigid connections.
Support strut channel at a right angle to the beam.
Attach these light duty hangers to beams and other structural elements. They include a stiff wire for supporting ceilings, lighting fixtures, and other lightweight material.
Suspend and route flat-bottomed objects such as strut channel and small duct.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.
A mounting plate provides a more secure hold at the mounting surface.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.
With five times the capacity of standard C-clamps, these are the highest capacity clamps we offer.
These clamps have twice the capacity of standard C‐clamps.
Plastic clamping surfaces prevent damage to material.
These clamps are made of stainless steel for excellent corrosion resistance.
Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.
Lighter weight than other metal clamps, these are less likely to bend thin material.
All components of these clamps are made of aluminum-bronze that is Factory Mutual approved. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
A bright finish makes these clamps easy to see.
With no handle or protruding screw, these clamps can fit into tight spaces.
The clamp body is extra-slim to fit into narrow openings.
Three screws apply pressure to three sides of a workpiece.
Clamp farther in from the edge of a workpiece than with other C‐clamps.
Hold the workpiece down against a bench or table.
The jaws move in unison to apply even pressure and prevent twisting.
Apply pressure to the side of a workpiece as well as the top and bottom.
Replace a fixed clamping surface with a swiveling pad that compensates for uneven workpieces.
Press the quick‐release button and slide the screw into position to make adjustments in less time.
For repetitive clamping, turn the holding screw to adjust the opening size one time, and then use the handle to secure and release workpieces.
Attach to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.
Attach to the end of a screw or threaded stud—the serrated face swivels to grip uneven and angled surfaces. Also known as toggle and swivel-foot pads.
The contact area is covered in plastic to protect soft metal and polished surfaces. Attach these tips to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.
Create a grounding path to prevent static charge buildup.
Designed specifically for use with welding circuits.
Lift metal plates by hand by gripping the edge.
Clamps can take a metal plate that is stacked horizontally and tilt it up 90° to lift vertically. After lifting, clamps can place the plate back down in the original position (plate can not be flipped over).
These tongs firmly grab flat and tapered beams.
Use in pairs with a two-leg sling to transfer metal plates in a horizontal position. Unlike other plate-lifting clamps, these can pick up multiple plates at the same time.
Pads on these clamps prevent the grip from biting into the load.
Use these clamps to raise a metal plate straight up from its original vertical position.