Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Use with soft plastic tubing to prevent the tube from collapsing.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Use these sleeves with compression nuts and fittings to create a strong seal on stainless steel tubing.

Pair these nuts with vibration-resistant compression sleeves and fittings for a strong seal on stainless steel tubing.

The thick walls of these fittings can withstand more than twice the pressure of standard compression fittings.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Use at pressures up to 4,300 psi.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Use these sleeves with a nut and fitting to provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

Use these nuts with compression sleeves and fittings, also known as bite fittings, to create a strong seal on steel tubing.

Use these sleeves—also known as ferrules—with high-pressure compression nuts and fittings. They withstand about twice as much pressure as sleeves for standard compression fittings, so they’re good for hydraulic power applications.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

With a nickel-plated finish, these compression fittings resist corrosion better than plain brass fittings.

Create a strong seal on copper tubing when you couple these nuts with compression sleeves and fittings.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

These fittings include a nut with a built-in sleeve, so there’s no need to remove the nut for assembly.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight seal on tubing that is flared to 37°.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO B-shape plugs and sockets.

Use these couplings at pressures up to 10,000 psi. Also known as flush-face couplings, the plugs and sockets have a flat face, which allows them to mate close together, reducing fluid loss when connecting and disconnecting the line. They are compatible with High-Pressure Minimal-Spill-shape plugs and sockets.

Use these dust caps and plugs to keep contaminants out of your hose line.

Use these dust caps and plugs to keep contaminants out of your hose line.

Use these couplings at pressures up to 5,000 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with International Standard ISO A-shape plugs and sockets.

Use these couplings at pressures up to 6,500 psi. They consist of a plug and socket that connect and disconnect quickly. Use them if you need frequent access to a line. They are compatible with Snap-Tite H-Shape plugs and sockets.

Add quick connection points for mechanical gauges and other diagnostic equipment to your line. These couplings are also known as test ports and diagnostic couplings.

Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system.

Crimp these fittings onto hydraulic hose for a permanent, leak-tight connection. Since they crimp on, they handle higher pressure than screw-on fittings.

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

To minimize fluid loss when connecting and disconnecting your line, these couplings have flat faces for a close fit and shut-off valves to stop the flow—they meet ISO 16028, which is an international standard for hose couplings.

Couplings are metal, which has better durability than plastic cam-and-groove hose couplings. Also known as dry disconnects and double shut-off couplings, they have a shut-off valve in the plug and the socket for minimal fluid loss when disconnecting your hose line.

Built with ball bearings, these fittings continuously swivel 360° before and after installation to prevent your hose from twisting, kinking, and failing. They’re made of 316 stainless steel, so they won’t corrode from a wide variety of chemicals, as well as fuels, gasoline, and oil.

When you need access to your line, don’t waste time threading and unthreading your fittings. This hose has a quick-disconnect fitting on both ends. It bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose.

The new standard for rubber hydraulic hose, this hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose. It comes with female threaded fittings already attached, saving you time.

For frequent connections, this hose has a socket end that's faster to connect and disconnect than a threaded fitting. This hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose, thanks to its two layers of blended rubber.

The new standard for rubber hydraulic hose, this hose bends twice as sharply and resists wear and tear 80 times better than our basic hydraulic hose.

Use this hose to transfer fluid between pumps, cylinders, and other parts of your hydraulic system.

Although only half the weight, this hose resists wear and tear 240 times better than our standard rubber hydraulic hose. The fittings come attached, so this hose is ready to connect to a male threaded fitting on one end and a female one on the other.

Made of nylon with a polyurethane cover, this hose is half the weight but 240 times better at resisting wear and tear than our standard rubber hydraulic hose. The male threaded fittings come already attached to save you time.

Attach push-on barbed fittings to this hose for use in low-pressure hydraulic applications. No clamps are needed to secure fittings to the hose; the more you pull on the fittings, the tighter the hose will grip.

Internally reinforced with four steel wire spirals, this hose resists bursting from rapid changes in pressure and flow. To save you time, this hose comes with female threaded fittings already attached.

With four steel wire spirals for reinforcement, this hose handles rapid changes in pressure and flow without bursting.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

The strongest steel fittings we offer, these can withstand extreme-pressure applications.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

Combine an adapter with a two-piece pipe flange (sold separately) to build a customized flange connection for noncorrosive environments.

Typically used with high-pressure iron and steel threaded pipe fittings. Also known as Schedule 160.

A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slide the pipe into the socket and weld.

Forged for extra strength, these heavy duty unthreaded flanges can withstand high-pressure applications.

Also known as Pressure Class 6000 fittings, these heavy duty forged fittings are the strongest steel fittings we offer.

These fittings are made to tighter tolerances than other stainless steel pipe fittings. They are also known as instrumentation fittings.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Also known as Code 61 SAE hydraulic flanges.

Also known as ANSI flanges.

Use these heavy duty forged flanges for high-pressure applications.

Typically used with thick-wall and high-pressure stainless steel unthreaded pipe fittings.