About Pipe Size and Spray Nozzles
More
Diesel-Fuel Hose Nozzles
Control the flow while dispensing diesel fuel. Nozzles are aluminum, which is lightweight with good corrosion resistance.
Nozzles with manual shut-off have a trigger to stop the flow. Do not leave the nozzle unattended when in use.
Nozzles with three-position hold-open clip allow you to dispense fuel without holding the trigger.
Style D has the largest spout and the highest flow rate of all the nozzles for use with trucks, buses, and other heavy-duty bulk fueling applications.
For technical drawings and 3-D models, click on a part number.
Spout | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Style | Max. Flow Rate, gpm | Pipe Size  | Connection | Max. Pressure | Temperature Range, °F | OD | Lg. | Material | Shut-Off Type | Each | |
Nozzles with Three-Position Hold-Open Clip | |||||||||||
| D | 100 | 1 1/4 | Threaded NPT Female | 50 psi @ 72° F | -20° to 125° | 1 1/4" | 7 1/4" | Aluminum | Manual | 0000000 | 0000000 |
Threaded Swivels for Hose Nozzles
Connect these swivels to the threaded end of your dispensing hose. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.
Aluminum swivels are lighter in weight than brass swivels. Anodized aluminum swivels have better corrosion resistance than uncoated aluminum. Chrome-plated brass swivels have comparable corrosion resistance to anodized aluminum swivels, but are softer, so they’re easier to thread together. They have a bright, shiny appearance.
Straight swivels rotate at the female connection point only; they are also known as inline swivels.
For technical drawings and 3-D models, click on a part number.
| Pipe Size | Connection | Max. Pressure | Temperature Range, °F | Lg. | Each | |
Anodized Aluminum | ||||||
|---|---|---|---|---|---|---|
For Use With Gasoline, Hydraulic Fluid, and Coolant | ||||||
| 1 1/4 × 1 1/4 | Threaded NPT Female × Threaded NPT Male | 150 psi @ 72° F | -65° to 250° | 4 1/2" | 0000000 | 0000000 |
Chrome-Plated Brass | ||||||
For Use With Gasoline, Hydraulic Fluid, and Coolant | ||||||
| 1 1/4 × 1 1/4 | Threaded NPT Female × Threaded NPT Male | 150 psi @ 72° F | -65° to 250° | 4 1/2" | 0000000 | 000000 |
Barbed Swivels for Hose Nozzles
Slide the barbed end of these swivels into your dispensing hose and connect with a clamp. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely. They are also known as inline swivels. Swivels are anodized aluminum, which is lightweight with good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Anodized Aluminum | |||||||
|---|---|---|---|---|---|---|---|
| For Hose ID | Pipe Size | Connection | Max. Pressure | Temperature Range, °F | Lg. | Each | |
For Use With Gasoline, Hydraulic Fluid, and Coolant | |||||||
| 1 1/4" | 1 1/4 | Barbed Male × Threaded NPT Male | 150 psi @ 72° F | -65° to 250° | 3 7/8" | 0000000 | 0000000 |
Clamp-On Flat Spray Nozzles
Drill a hole anywhere along a pipe and snap on these nozzles. Spray tips can be removed for cleaning, but cannot be replaced with another tip. Made of reinforced plastic, all have a 300 Series stainless steel clamp that grips the pipe and an EPDM rubber gasket that prevents leaks. They're good for foam control and produce a flat, thin spray pattern.
For technical drawings and 3-D models, click on a part number.
Flow Rate, gpm | Each | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| @ 20 psi | @ 40 psi | @ 100 psi | Orifice Dia. | For Hole Dia. | Overall Dia. | Lg. | Max. Pressure, psi | Max. Temp., °F | Reinforcement Material | Max. Swivel Angle | Spray Angle | 1-9 | 10-Up | |
Polypropylene Plastic | ||||||||||||||
For 1 1/4 Pipe Size | ||||||||||||||
| 0.7 | 1 | 1.5 | 0.07" | 9/16" | 1 13/16" | 2 1/2" | 100 | 175° | Glass | 52° | 80° | 000000000 | 000000 | 000000 |
| 1.4 | 2 | 3.2 | 0.1" | 9/16" | 1 13/16" | 2 1/2" | 100 | 175° | Glass | 52° | 65° | 000000000 | 00000 | 00000 |
| 2.1 | 3 | 4.7 | 0.12" | 9/16" | 1 13/16" | 2 1/2" | 100 | 175° | Glass | 52° | 65° | 000000000 | 00000 | 00000 |
| 2.8 | 4 | 6.3 | 0.14" | 9/16" | 1 13/16" | 2 1/2" | 100 | 175° | Glass | 52° | 65° | 000000000 | 00000 | 00000 |
| 3.5 | 5 | 7.9 | 0.16" | 9/16" | 1 13/16" | 2 1/2" | 100 | 175° | Glass | 52° | 65° | 000000000 | 00000 | 00000 |
| 4.9 | 7 | 11.1 | 0.19" | 9/16" | 1 13/16" | 2 1/2" | 100 | 175° | Glass | 52° | 65° | 000000000 | 00000 | 00000 |
Clamp-On Flat Spray Nozzles with Quick-Change Tip
These nozzles have replaceable tips that are removable with a quarter-turn. All tips have two O-rings to prevent leaks. Drill a hole anywhere along a pipe and snap on these nozzles. Made of reinforced plastic, all have a 300 Series stainless steel clamp that grips the pipe and an EPDM rubber gasket that prevents leaks. They're good for foam control and produce a flat, thin spray pattern.
For technical drawings and 3-D models, click on a part number.
Nozzles | Replacement Tips | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Flow Rate, gpm | Each | Each | |||||||||||||||
| @ 20 psi | @ 40 psi | @ 100 psi | Orifice Dia. | For Hole Dia. | Overall Dia. | Lg. | Max. Pressure, psi | Max. Temp., °F | Reinforcement Material | Max. Swivel Angle | Spray Angle | 1-9 | 10-Up | 1-9 | 10-Up | ||
Polypropylene Plastic | |||||||||||||||||
For 1 1/4 Pipe Size | |||||||||||||||||
| 0.7 | 1 | 1.5 | 0.07" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 80° | 00000000 | 000000 | 000000 | 0000000 | 000000 | 000000 |
| 1.4 | 2 | 3.2 | 0.1" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 65° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 2.1 | 3 | 4.7 | 0.12" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 65° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 2.8 | 4 | 6.3 | 0.14" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 65° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 3.5 | 5 | 7.9 | 0.16" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 65° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 4.9 | 7 | 11.1 | 0.19" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 65° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
Clamp-On Full-Cone Spray Nozzles
Drill a hole anywhere along a pipe and snap on these nozzles. Spray tips can be quickly and easily removed with a quarter-turn for cleaning and replacement. Tips have two O-rings to prevent leaks. Made of reinforced plastic, all have a Series 300 stainless steel clamp that grips the pipe and an EPDM rubber gasket that prevents leaks. They provide a uniform distribution of droplets that are good for cooling and dust- and foam-control applications.
For technical drawings and 3-D models, click on a part number.
Nozzles | Replacement Tips | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Flow Rate, gpm | Each | Each | |||||||||||||||
| @ 20 psi | @ 40 psi | @ 100 psi | Orifice Dia. | For Hole Dia. | Overall Wd. | Lg. | Max. Pressure, psi | Max. Temp., °F | Reinforcement Material | Max. Swivel Angle | Spray Angle | 1-9 | 10-Up | 1-9 | 10-Up | ||
Polypropylene Plastic | |||||||||||||||||
For 1 1/4 Pipe Size | |||||||||||||||||
| 0.1 | 0.2 | 0.3 | 0.03" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 55° | 00000000 | 000000 | 000000 | 0000000 | 000000 | 000000 |
| 0.4 | 0.5 | 0.8 | 0.05" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 105° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 0.4 | 0.6 | 0.9 | 0.05" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 53° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 0.7 | 1 | 1.5 | 0.06" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 75° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |
| 2.8 | 4 | 6.3 | 0.1" | 9/16" | 1 13/16" | 3" | 100 | 175° | Glass | 52° | 120° | 00000000 | 00000 | 00000 | 0000000 | 00000 | 00000 |