About Rod Ends
More
Ball Joint Rod Ends
Made of steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends. They don’t come lubricated, so you’ll need to lubricate during installation and on an ongoing basis.
Zinc-plated steel rod ends provide moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
Ball Joints | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| M12 × 1.25 mm | 12mm | 49° | 30mm | 16mm | 54mm | 33mm | 4,050 | Zinc-Plated Carbon Steel | 00000000 | 000000 | |
| M12 × 1.75 mm | 12mm | 27° | 30mm | 16mm | 54mm | 33mm | 5,800 | Zinc-Plated Carbon Steel | 00000000 | 00000 | |
Internally Threaded Ball Joint Rod Ends
Made of steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends. They don’t come lubricated, so you’ll need to lubricate them during installation and on an ongoing basis.
Zinc-plated steel rod ends provide moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
Ball Joints | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| M12 × 1.75 mm | 12mm | 27° | 30mm | 16mm | 50mm | 24mm | 5,800 | Zinc-Plated Carbon Steel | 00000000 | 000000 | |
Ball Joint Rod Ends with Grease Fitting
Connect your grease gun to the fitting to lubricate. Made of steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.
For technical drawings and 3-D models, click on a part number.
Internally Threaded Ball Joint Rod Ends with Grease Fitting
Connect your grease gun to the fitting to lubricate. These rod ends don’t come lubricated, so you'll need to lubricate during installation and on an ongoing basis. Made of steel, they generally handle higher loads than stainless steel, aluminum, and nylon rod ends.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M12 × 1.75 mm | 12mm | 27° | 30mm | 16mm | 50mm | 24mm | 5,800 | Carbon Steel | 000000 | 000000 |
Lubrication-Free Ball Joint Rod Ends
A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication. Made of steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends. All are zinc plated, so they resist corrosion for a short time before the finish is consumed and the steel is exposed.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M12 × 1.25 mm | 12mm | 17° | 30mm | 16mm | 54mm | 33mm | 10,000 | Zinc-Plated Alloy Steel | Right Hand | 00000000 | 000000 |
| M12 × 1.75 mm | 12mm | 17° | 30mm | 16mm | 54mm | 33mm | 10,000 | Zinc-Plated Alloy Steel | 00000000 | 00000 |
Internally Threaded Lubrication-Free Ball Joint Rod Ends
A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication. Made of steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends. All are zinc plated, so they resist corrosion for a short time before the finish is consumed and the steel is exposed.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M12 × 1.25 mm | 12mm | 17° | 30mm | 16mm | 50mm | 24mm | 10,000 | Zinc-Plated Chrome-Moly Steel | 0000000 | 000000 | |
| M12 × 1.75 mm | 12mm | 17° | 30mm | 16mm | 50mm | 24mm | 10,000 | Zinc-Plated Chrome-Moly Steel | 0000000 | 00000 |
Internally Threaded Oil-Embedded Ball Joint Rod Ends with Grease Fitting
An oil-embedded bronze insert slowly releases lubricant to the rod end. Relubrication is recommended but not required. Connect your grease gun to the fitting to relubricate. Made of zinc-plated steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends and offer moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID, mm | Max. Ball Swivel | O'all Wd., mm | O'all Thick., mm | Shank Center Lg., mm | Shank Thread Lg., mm | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M12 × 1.75 mm | 12 | 17° | 30 | 16 | 50 | 24 | 7,750 | Zinc-Plated Carbon Steel | 0000000 | 000000 |
Oil-Embedded Ball Joint Rod Ends with Grease Fitting
An oil-embedded bronze insert slowly releases lubricant to the rod end. Relubrication is recommended but not required. Connect your grease gun to the fitting to relubricate. Made of zinc-plated steel, these rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends and offer moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID, mm | Max. Ball Swivel | O'all Wd., mm | O'all Thick., mm | Shank Center Lg., mm | Shank Thread Lg., mm | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M12 × 1.75 mm | 12 | 17° | 30 | 16 | 54 | 33 | 7,750 | Zinc-Plated Carbon Steel | 0000000 | 000000 |
Extended-Life Ball Joint Rod Ends
Seals keep out dirt and an oil-embedded foam insert slowly releases lubricant for a long life. You can remove the insert to add more oil if it starts to run dry. These rod ends have an eyelet and a ball that swivels to support angular misalignment. Made of zinc-plated steel, they have moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
| M12 × 1.25 mm | 12mm | 27° | 30mm | 18mm | 54mm | 33mm | 5,800 | Zinc-Plated Carbon Steel | 0000000 | 000000 | |
| M12 × 1.75 mm | 12mm | 27° | 30mm | 18mm | 54mm | 33mm | 5,800 | Zinc-Plated Carbon Steel | 0000000 | 00000 |
Corrosion-Resistant Ball Joint Rod Ends
Made of stainless steel, these rod ends provide excellent corrosion resistance. A PTFE liner allows smooth ball rotation and eliminates the need for lubrication.
For technical drawings and 3-D models, click on a part number.
Internally Threaded Corrosion-Resistant Ball Joint Rod Ends
Made of stainless steel, these rod ends provide excellent corrosion resistance. A PTFE liner allows smooth ball rotation and eliminates the need for lubrication.
For technical drawings and 3-D models, click on a part number.
Internally Threaded Chemical-Resistant Ball Joint Rod Ends
Made of impact-resistant nylon, these rod ends withstand corrosion as well as fuels, lyes, and weak acids. They are also 80% lighter than steel rod ends. A self-lubricating nylon ball provides maximum abrasion resistance and eliminates the need for lubrication.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Temp. Range, °F | Material | Specifications Met | Shank Thread Direction | Each | |
| M10 × 1.25 mm | 10mm | 12.5° | 30mm | 10mm | 43mm | 10mm | 220 | -20° to 175° | Nylon Plastic | ISO 12240-4 | Right Hand | 00000000 | 000000 |
| M10 × 1.5 mm | 10mm | 12.5° | 30mm | 10mm | 43mm | 10mm | 220 | -20° to 175° | Nylon Plastic | ISO 12240-4 | Right Hand | 00000000 | 00000 |
High-Load Ball Joint Rod Ends
Rod ends with Nylon/PTFE insert have a durable, self-sealing insert that reduces wear.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
Ball Joints | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Nylon/PTFE Plastic Blend Insert | |||||||||||
| M12 × 1.75 mm | 12mm | 17° | 30mm | 16mm | 54mm | 33mm | 15,300 | Chrome-Moly Steel | 0000000 | 000000 | |
Internally Threaded High-Load Ball Joint Rod Ends
These steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends. PTFE allows smooth rotation and eliminates the need for lubrication.
Rod ends with Nylon/PTFE insert have a durable, self-sealing insert that reduces wear.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Material | Choose a Shank Thread Direction | Each | |
Ball Joints | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Nylon/PTFE Plastic Blend Insert | |||||||||||
| M12 × 1.75 mm | 12mm | 17° | 30mm | 16mm | 50mm | 24mm | 15,300 | Chrome-Moly Steel | 0000000 | 000000 | |