Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

Tighten and loosen fasteners at an angle by pivoting the head on these sockets.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

The hex shape achieves the best possible grip on hex fasteners to prevent rounding their points.

These short sockets fit spaces where height clearance is limited.

Pivot the head to access fasteners from an angle.

Designed for use with stainless steel fasteners, these sockets are more corrosion resistant than steel sockets and less likely to flake.

Eliminate the risk of your socket falling while reaching into your workspace with these flex sockets that have an integrated extension.

Pivot the head to access fasteners from an angle.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.

A rubber insert grips the plug to prevent damage.

Switch out worn or damaged bits instead of replacing your entire bit socket.

A magnet holds the fastener securely enough to drive self-tapping screws.

With a smaller OD than standard sockets, these fit between tightly spaced fasteners.

Extra length allows access to fasteners on long bolts.

Attach these sockets to your spline-drive impact wrench.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Designed to remove and install dual wheels on trucks and trailers, these sockets have a hex recess for accessing lug nuts and a square recess to turn the threaded shafts found on inner wheels.

These sockets are designed to tolerate continuous use with power tools and impact tools in high-volume production and assembly.

Extra-long bits allow access to hard-to-reach fasteners.

Pivot the head of the sockets in these sets to access fasteners from an angle.

A spring-loaded ball on the bit holds fasteners in place as you drive them, including nonmagnetic fasteners like stainless steel screws.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Two spring-loaded balls inside these sockets firmly hold nuts and bolts in place as you turn them, including nonmagnetic fasteners like stainless steel screws.

Suitable for occasional maintenance work, these sets are imported.

Pivot the head to access fasteners from an angle.

Turn 90° elbow fittings that are in tight spots with the sockets in these sets.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Extra-long bits help you access hard-to-reach fasteners.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

Carry fewer impact sockets—these five reversible impact sockets turn 10 fastener sizes. Flip the socket around to turn a different size.

Use one socket to switch between two fastener sizes.

Remove and install dual wheels on trucks and trailers with the sockets in these sets.

The rail is smooth plastic so the clips move more easily than on steel-rail organizers.

Move the sliding clips to any position along the rail to hold a variety of sockets.

Magnets hold sockets securely in place.

These are also known as tappet wrenches.

One head is angled for access to hard-to-reach fasteners. These are also known as ignition wrenches.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These lightweight tools are also known as AN (Army-Navy) wrenches.

Strike the handle with a hammer to break stuck fasteners free. These are also known as slugging wrenches.

The head is offset 45° to provide additional clearance when reaching over obstructions.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Made of stainless steel, these wrenches have excellent corrosion resistance.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

One head is angled 75° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

The slim heads fit into tight spaces and around thin fasteners.

The heads are offset to provide clearance for reaching over obstructions.

The heads are offset 45° to provide clearance for reaching over obstructions.