With a stainless steel float and float rod, these gauges resist corroding from chemicals. Their indicator moves up as your tank fills. Check the indicator against the graduation marks to see how full your tank is and if you need to fill or drain it. Plastic protects the indicator's movement, saving you from inaccurate readings.

Alarms can be set to flash and sound at levels critical to your system.

Remote-reading displays let you check readings from up to 100 ft. away. They have an alarm that sounds when the level is too high or too low.

For technical drawings and 3-D models, click on a part number.

Made with clear, shatter-resistant plastic, these indicators don't require a shield to protect them like other oil-level indicators, so you can check your hydraulic fluid or oil level from any angle. They’re often found on gear boxes, crank cases, and other reservoirs. These indicators mount from the outside of your tank. The vent prevents pressure buildup, which can affect the level displayed. Within the vent, there is a filter for keeping out particles as small as table salt. Unthread the vent to clean its filter or to replace it with your own vent, plug, fitting, or sensor. These indicators also have adjustable rings for marking levels critical to your system.

For technical drawings and 3-D models, click on a part number.

Check the level of liquids containing chemicals such as alcohol-based solvents, boric acid, and sodium bicarbonate. These indicators can be used in pressurized applications where overflow is a concern. All have an aluminum gauge shield that protects the glass window from impact. Clear liquids magnify a red line at the back of the window, so their levels are easier to see.

Screw-in indicators mount from the outside of your tank into threaded pipe or threaded holes.

Through-wall indicators mount from the inside of your tank through unthreaded holes. Secure with nuts on the inside of your tank.

Screw-in/through-wall indicators give you the option to mount from the inside or outside of your tank. Use the mounting nuts on the inside of your tank to attach them through unthreaded holes or thread them into pipe or threaded holes on the tank’s outside.

For technical drawings and 3-D models, click on a part number.

Shut-off valves stop flow so you can clean and replace gauge glass without removing these indicators from your equipment.

316 stainless steel indicators are more corrosion resistant than brass or bronze indicators.

Use indicators with stainless steel drain valve on expansion tanks.

Indicators with needle stem have a stem in the lower shut-off valve to clear the orifice as the valve closes.

Indicators with automatic shut-off will temporarily close if the gauge glass breaks. The valves must be closed manually for permanent shut-off.

Avoid overfilling—these indicators pop up when your tank is almost full.

Indicators with a polypropylene float have a plastic window to protect the indicator’s movement and keep it working properly. When you see the indicator behind the overfill alert warning, you'll know your tank is almost full.

Alarms flash and sound when your tank is almost full.

For technical drawings and 3-D models, click on a part number.

Monitor liquid level in applications that have vibration, high pressures, and high temperatures. These indicators have steel chambers, glass windows, and seals made of fiber and SBR rubber to resist corrosion and withstand higher temperatures than other level indicators. Use them with a wide variety of liquids, such as petroleum, chemicals, and natural gas. All meet ASME BPVC.VIII.1 safety standards for pressure vessels, so they’re approved for use in low-pressure water and steam applications too. Their gauge is made of reflex glass, which shows the level of liquid behind the glass, but not the liquid’s color or any particulates in it. Also known as armored level gauges.

Add shut-off valves to stop flow with the turn of a wheel. They help you access indicators in order to clean or replace the glass or the entire indicator. These valves also stop flow automatically if the indicator glass breaks, preventing the loss of fluid. However, for permanent shut-off you must close them manually. Put one valve on top of your indicator and one on the bottom for a 90° connection between the indicator and your tank. To connect the female threads on your indicator to the female gauge threads on the shut-off valve, use a male pipe nipple (not included).

For technical drawings and 3-D models, click on a part number.