McMaster-Carr logo
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    128 Products

    Wedge Anchors for Concrete

    Image of ProductInUse. Front orientation. Anchors. Wedge Anchors for Concrete.
    Image of Product. Front orientation. Contains Annotated. Anchors. Wedge Anchors for Concrete.
    Secure junction boxes, safety railings, and structural beams in concrete floors. These anchors have a wedge-shaped base that expands against the hole’s sides, forming a tight grip that withstands high pull-out forces. Since the grip is focused at the base, these anchors are best suited for concrete, which can handle the gripping pressure better than softer block and brick. However, they require holes that match the anchors' diameter exactly to achieve their pull-out strength, making them more difficult to install than sleeve anchors.
    To install, drive the anchor through your component into a drilled hole until the washer and nut meet the surface. Then, tighten the nut to expand the anchor base. Remove your component by unfastening the nut, but the anchor itself cannot be removed.
    Corrosion-Resistant Galvanized Steel—Combine the strength of steel with the rust resistance of stainless steel. These anchors are an economical alternative to 18-8 stainless steel in wet and outdoor environments, but they’ll corrode or pit when exposed to salt water and chemicals.
    Ultimate
    Strength, lbf
    Each
    Package
    Lg.
    Thread
    Size
    Min. Thread
    Lg.
    Min. Installation
    Dp.
    Drill Bit
    Size
    Pull-Out
    Shear
    Conditions
    Tested In
    Installation
    Torque, ft·lbf
    Each
    Pkg.
    Qty.
    Pkg.
    Corrosion-Resistant Galvanized Steel
     
    1/4" Diameter
    1 3/4"1/4"-20
    5/8"1 1/4"1/4"1,6802,5204,000 psi Concrete800000000000000100000000000000000
    2 1/4"1/4"-20
    1 1/8"1 1/4"1/4"1,6802,5204,000 psi Concrete8000000000000010000000000000000
    3 1/4"1/4"-20
    2 1/8"1 1/4"1/4"1,6802,5204,000 psi Concrete8000000000000010000000000000000
     
    3/8" Diameter
    2 1/4"3/8"-16
    7/8"1 3/4"3/8"3,8803,9204,000 psi Concrete2500000000000005000000000000000
    2 3/4"3/8"-16
    1 3/8"1 3/4"3/8"3,8803,9204,000 psi Concrete2500000000000005000000000000000
    3"3/8"-16
    1 5/8"1 3/4"3/8"3,8803,9204,000 psi Concrete2500000000000005000000000000000
    3 3/4"3/8"-16
    2 3/8"1 3/4"3/8"3,8803,9204,000 psi Concrete2500000000000005000000000000000
    5"3/8"-16
    3 1/8"1 3/4"3/8"3,8803,9204,000 psi Concrete2500000000000005000000000000000
    7"3/8"-16
    4 1/2"1 3/4"3/8"3,8803,9204,000 psi Concrete2500000000000001000000000000000
     
    1/2" Diameter
    2 3/4"1/2"-13
    1"2 1/4"1/2"6,3206,9204,000 psi Concrete5500000000000002500000000000000
    3 3/4"1/2"-13
    2"2 1/4"1/2"6,3206,9204,000 psi Concrete5500000000000002500000000000000
    4 1/4"1/2"-13
    3"2 1/4"1/2"5,0686,8284,000 psi Concrete5000000000000002500000000000000
    5 1/2"1/2"-13
    3 5/8"2 1/4"1/2"6,3206,9204,000 psi Concrete5500000000000002500000000000000
    7"1/2"-13
    4 3/8"2 1/4"1/2"6,3206,9204,000 psi Concrete5500000000000002500000000000000
    8 1/2"1/2"-13
    2"2 1/4"1/2"6,3206,9204,000 psi Concrete5500000000000001000000000000000
     
    5/8" Diameter
    3 1/2"5/8"-11
    1 3/8"2 3/4"5/8"9,76011,9604,000 psi Concrete9500000000000001000000000000000
    4 1/2"5/8"-11
    2"2 3/4"5/8"9,76011,9604,000 psi Concrete9500000000000001000000000000000
    5"5/8"-11
    3"2 3/4"5/8"9,76011,9604,000 psi Concrete9500000000000001000000000000000
    6"5/8"-11
    3 7/8"2 3/4"5/8"9,76011,9604,000 psi Concrete9500000000000001000000000000000
    7"5/8"-11
    3 1/2"2 3/4"5/8"9,76011,9604,000 psi Concrete9500000000000001000000000000000
    8 1/2"5/8"-11
    4 7/8"2 3/4"5/8"9,76011,9604,000 psi Concrete9500000000000001000000000000000
    10"5/8"-11
    2"2 3/4"5/8"9,76011,9604,000 psi Concrete95000000000000001000000000000000
     
    3/4" Diameter
    4 1/4"3/4"-10
    1 3/4"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000001000000000000000
    4 3/4"3/4"-10
    2 1/4"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000001000000000000000
    5 1/2"3/4"-10
    3"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000001000000000000000
    6 1/4"3/4"-10
    3 5/8"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000001000000000000000
    7"3/4"-10
    4 3/8"3 3/4"3/4"13,16015,8804,000 psi Concrete175000000000000001000000000000000
    8 1/2"3/4"-10
    2 1/4"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000000400000000000000
    10"3/4"-10
    2 1/4"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000000400000000000000
    12"3/4"-10
    2 1/4"3 3/4"3/4"13,16015,8804,000 psi Concrete17500000000000000400000000000000
     
    7/8" Diameter
    6"7/8"-9
    2 1/8"4"7/8"16,60032,5204,000 psi Concrete25000000000000000400000000000000
    8"7/8"-9
    2 1/8"4"7/8"16,60032,5204,000 psi Concrete25000000000000000400000000000000
    10"7/8"-9
    2 1/8"4"7/8"16,60032,5204,000 psi Concrete25000000000000000400000000000000
     
    1" Diameter
    6"1"-8
    2 1/4"4"1"20,40032,4924,000 psi Concrete30000000000000000400000000000000
    9"1"-8
    2 1/4"4"1"20,40032,4924,000 psi Concrete30000000000000000400000000000000
    12"1"-8
    2 1/4"4"1"20,40032,4924,000 psi Concrete30000000000000000400000000000000
     
    1 1/4" Diameter
    9"1 1/4"-7
    2 3/4"5 5/8"1 1/4"28,76047,0004,000 psi Concrete400000000000000004000000000000000
    12"1 1/4"-7
    2 3/4"5 5/8"1 1/4"28,76047,0004,000 psi Concrete400000000000000004000000000000000
     

    Hook Anchors for Concrete

    Fasten everything from signposts to support beams. Install these anchors in wet concrete during construction, with their threads sticking out of the surface. Designed for permanent installations, you'd have to cut these anchors out to remove them.
    L-Hook
    Image of Product. Front orientation. Contains Annotated. Anchors. Hook Anchors for Concrete, L-Hook.
    Corrosion-Resistant Hot-Dipped Galvanized Steel—Combines the strength of steel with the rust resistance of stainless steel. These anchors are an economical alternative to 18-8 stainless steel in wet and outdoor environments, but they’ll corrode or pit when exposed to salt water and chemicals. They must be used with other hot-dipped galvanized fasteners.
    Ultimate
    Strength
    Lg.
    Thread
    Size
    Min. Thread
    Lg.
    Hook
    Lg.
    Tensile Strength,
    psi
    Pull-Out
    Shear
    Specs.
    Met
    Each
    Corrosion-Resistant Hot-Dipped Galvanized Steel
     
    3/8" Diameter
    8"3/8"-16
    2 1/2"2"58,000Not RatedNot RatedASTM A3600000000000000
    10"3/8"-16
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    12"3/8"-16
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    14"3/8"-16
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    24"3/8"-16
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
     
    1/2" Diameter
    8"1/2"-13
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    10"1/2"-13
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    12"1/2"-13
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    14"1/2"-13
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    16"1/2"-13
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    18"1/2"-13
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
     
    5/8" Diameter
    8"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    10"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    12"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A360000000000000
    14"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A3600000000000000
    16"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A3600000000000000
    18"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A3600000000000000
    24"5/8"-11
    2 1/2"2"58,000Not RatedNot RatedASTM A3600000000000000
     
    3/4" Diameter
    8"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A360000000000000
    10"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A360000000000000
    12"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    14"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    16"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    18"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    24"3/4"-10
    3"2 3/4"58,000Not RatedNot RatedASTM A3600000000000000
     
    1" Diameter
    12"1"-8
    4"3 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    16"1"-8
    4"3 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    18"1"-8
    4"3 3/4"58,000Not RatedNot RatedASTM A3600000000000000
    24"1"-8
    4"3 3/4"58,000Not RatedNot RatedASTM A3600000000000000
     
    J-Hook
    Image of Product. Front orientation. Contains Annotated. Anchors. Hook Anchors for Concrete, J-Hook.
    Corrosion-Resistant Hot-Dipped Galvanized Steel—Combines the strength of steel with the rust resistance of stainless steel. These anchors are an economical alternative to 18-8 stainless steel in wet and outdoor environments, but they’ll corrode or pit when exposed to salt water and chemicals. They must be used with other hot-dipped galvanized fasteners.
    Hook
    Ultimate
    Strength
    Lg.
    Thread
    Size
    Min. Thread
    Lg.
    Lg.
    Opening
    Tensile Strength,
    psi
    Pull-Out
    Shear
    Specs.
    Met
    Each
    Corrosion-Resistant Hot-Dipped Galvanized Steel
     
    3/8" Diameter
    8"3/8"-16
    2.5"1"1/2"58,000Not RatedNot RatedASTM A3600000000000000
    10"3/8"-16
    2.5"1"1/2"58,000Not RatedNot RatedASTM A360000000000000
    12"3/8"-16
    2.5"1"1/2"58,000Not RatedNot RatedASTM A360000000000000
    14"3/8"-16
    2.5"1"1/2"58,000Not RatedNot RatedASTM A360000000000000
     
    1/2" Diameter
    8"1/2"-13
    2.5"1 1/4"5/8"58,000Not RatedNot RatedASTM A360000000000000
    10"1/2"-13
    2.5"1 1/4"5/8"58,000Not RatedNot RatedASTM A360000000000000
    12"1/2"-13
    2.5"1 1/4"5/8"58,000Not RatedNot RatedASTM A360000000000000
    16"1/2"-13
    2.5"1 1/4"5/8"58,000Not RatedNot RatedASTM A360000000000000
    18"1/2"-13
    2.5"1 1/4"5/8"58,000Not RatedNot RatedASTM A3600000000000000
     
    5/8" Diameter
    8"5/8"-11
    2.5"1 1/4"3/4"58,000Not RatedNot RatedASTM A3600000000000000
    10"5/8"-11
    2.5"1 1/4"3/4"58,000Not RatedNot RatedASTM A3600000000000000
    12"5/8"-11
    2.5"1 1/4"3/4"58,000Not RatedNot RatedASTM A3600000000000000
    18"5/8"-11
    2.5"1 1/4"3/4"58,000Not RatedNot RatedASTM A3600000000000000
     
    3/4" Diameter
    8"3/4"-10
    3"1 1/2"1 1/8"58,000Not RatedNot RatedASTM A360000000000000
    10"3/4"-10
    3"1 1/2"1 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    12"3/4"-10
    3"1 1/2"1 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    14"3/4"-10
    3"1 1/2"1 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    18"3/4"-10
    3"1 1/2"1 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    24"3/4"-10
    3"1 1/2"1 1/8"58,000Not RatedNot RatedASTM A3600000000000000
     
    1" Diameter
    10"1"-8
    4"3 1/4"2 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    12"1"-8
    4"3 1/4"2 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    18"1"-8
    4"3 1/4"2 1/8"58,000Not RatedNot RatedASTM A3600000000000000
    24"1"-8
    4"3 1/4"2 1/8"58,000Not RatedNot RatedASTM A3600000000000000
     
    back to top