8-32 Fasteners | McMaster-Carr

Filter by

System of Measurement

Thread Size

Length

Material

Drive Style

Fastener Head Type

Finish

Threading

Head Diameter

Socket Head Profile

Rounded Head Style

Head Height

Thread Direction

Thread Type

Screw Size

Specifications Met

Drive Size

Flat Head Profile

Countersink Angle

Thread Spacing

DFARS Compliance

REACH Compliance

RoHS Compliance

How can we improve?

4,925 Products

Fastening and Joining

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Tapping Screws

Fasten a range of materials together without needing to tap the hole first

Tighten and loosen by hand without the need for tools

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

Captive Panel Screws

Captive Panel Screws

Secure panels and enclosures while still having access to them

Carriage Bolts

A smooth head provides a finished look while a square neck keeps the bolt in place when using a nut

Studs

Press, weld, or screw in place to add a threaded fastening point

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

Adhesive-Mount Nuts

Adhesive-Mount Nuts

Attach threads to material that’s too thin for a threaded insert

Threaded Inserts

Threaded Inserts

Create new threads or repair stripped threads

Press-Fit Nuts

Push into drilled or punched holes to add threads to thin panels

Clip-On Nuts

Slide onto the edge of thin panels to create a fastening point

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Screw-Mount Nuts

Screw-Mount Nuts

Mount with screws, rivets, and nails to add threads to a surface

Rivet-Mount Nuts

Rivet-Mount Nuts

Add threads in hard-to-reach areas and materials that are too thin to be tapped

Snap-In Nuts

Push into square holes in thin materials to add bolts for aligning off-center parts

Weld Nuts

Weld to metal surfaces to add permanent threads

Push Nuts

Press onto threads for a light duty hold that’s faster to install than typical nuts

Binding Barrels and Screws

Binding Barrels and Screws

Thread together for a low-profile fastener

Hex Nuts

Handle most general fastening needs

Locknuts

Hold fasteners in place to prevent loosening from vibration

Easy to tighten and loosen by hand for making frequent adjustments

Flange Nuts

The flange distributes pressure, so you don't need a washer

Coupling Nuts

Connect and extend threaded rods

Cap Nuts

Cover and protect threads while adding a finished look; also known as acorn nuts

Square Nuts

Flat sides won’t spin in channels and square holes

Socket Nuts

Install in recessed holes and tight spots where a wrench won’t fit; also known as Allen nuts

Sealing Nuts

Prevent leaks and block out contaminants with a rubber seal

Standoff Caps

Create a finished look on standoffs and protect them from dirt and debris

Standoffs

Threaded to separate or connect parts as well as position components in assemblies

Dowel Pins

Align parts before assembly or use as a pivot, shaft, or hinge to join moving components

Taper Pins

Fit snugly into tapered holes to secure, position, and align components

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Fabric Snaps

Join soft, heavy fabrics such as leather and canvas

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Anchors

Secure anything from signs to heavy machinery in concrete, brick, and drywall

Push Nut Installation Tools

Push Nut Installation Tools

Press nuts and retaining rings onto threaded fasteners and shafts

Rivet Nut Tools

Rivet Nut Tools

Install rivet nuts

Anchor Installation Tools

Anchor Installation Tools

Drive with a hammer to expand and secure anchors in place

Building and Machinery Hardware

Cam Handles

For fast clamping, push down on the handle to draw two parts together

Knobs

Position, tighten, and secure fixtures and equipment

T-Slotted Framing and Fittings

T-Slotted Framing and Fittings

The most versatile system, attach fittings along the continuous slots to build virtually anything

Strut Channel Framing and Fittings

Strut Channel Framing and Fittings

Secure fittings in the U-shaped channel to route conduit and pipe or build other structures

Fabricating and Machining

Lathe Tool Insert Holder Replacement Parts

Lathe Tool Insert Holder Replacement Parts

Replace clamps, screws, shims, and other parts in lathe tool insert holders

Clamps

Hold workpieces securely in place

Material Handling

Eyebolts

Route rope through the loop or attach hooks and shackles for lifting

Turnbuckles

Twist the body or end fittings to adjust the length and tension of attached rope and chain

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)