1/2"-13 Fasteners | McMaster-Carr

Filter by

System of Measurement

Thread Size

Length

Material

Threading

Finish

Fastener Head Type

Fastener Strength Grade/Class

Thread Direction

Thread Type

Thread Spacing

Head Width

Drive Style

Head Height

Specifications Met

Tensile Strength

Screw Size

Socket Head Profile

Nut Type

Head Diameter

Thread Fit

Drive Size

Grip Length

How can we improve?

4,218 Products

Fastening and Joining

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

Pentagon Head Screws

Pentagon Head Screws

Create a tamper-resistant joint with a head than can only be removed with a 5-point socket

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

Carriage Bolts

A smooth head provides a finished look while a square neck keeps the bolt in place when using a nut

T-Bolts

Turn by hand for easy fastening, use as a handle, or attach as a point for straps and clamps

Tighten and loosen by hand without the need for tools

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Hold-Down Bolts

Hold-Down Bolts

Hold material under the bent head while the other end is tightened down with a nut

12-Point Screws

12-Point Screws

12 contact points handle more torque than a hex head while a flange eliminates the need for a washer

Plow Bolts

The head sits flush with countersunk holes while the bolt stays in place when tightening a nut

Square Head Screws

Square Head Screws

Turn the large flat sides with a wrench into square holes that stop further rotation

Elevator Bolts

Create a flush joint to allow movement in tight spaces such as grain elevators and belting systems

Studs

Press, weld, or screw in place to add a threaded fastening point

Tapping Screws

Fasten a range of materials together without needing to tap the hole first

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

Captive Panel Screws

Captive Panel Screws

Secure panels and enclosures while still having access to them

Hex Nuts

Handle most general fastening needs

Locknuts

Hold fasteners in place to prevent loosening from vibration

Flange Nuts

The flange distributes pressure, so you don't need a washer

Tamper-Resistant Nuts

Tamper-Resistant Nuts

Hard to detach without special tools to prevent unwanted removal

Coupling Nuts

Connect and extend threaded rods

Easy to tighten and loosen by hand for making frequent adjustments

Socket Nuts

Install in recessed holes and tight spots where a wrench won’t fit; also known as Allen nuts

Cap Nuts

Cover and protect threads while adding a finished look; also known as acorn nuts

Split Nuts

Swivel to attach at any point on a threaded rod for quick installation

Push-Button Nuts

Push-Button Nuts

Disengage the threads to quickly slide along threaded rods

Square Nuts

Flat sides won’t spin in channels and square holes

Sealing Nuts

Prevent leaks and block out contaminants with a rubber seal

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Threaded Inserts

Threaded Inserts

Create new threads or repair stripped threads

Screw-Mount Nuts

Screw-Mount Nuts

Mount with screws, rivets, and nails to add threads to a surface

Weld Nuts

Weld to metal surfaces to add permanent threads

Press-Fit Nuts

Push into drilled or punched holes to add threads to thin panels

Push Nuts

Press onto threads for a light duty hold that’s faster to install than typical nuts

Snap-In Nuts

Push into square holes in thin materials to add bolts for aligning off-center parts

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Anchors

Secure structural joints in concrete, brick, and other building materials

Quick-Release Pin Receptacles

Quick-Release Pin Receptacles

Secure quick-release pins when you don’t have a through hole

Quick-Release Pins

Quick-Release Pins

Fasten or remove components on equipment with a spring-loaded retaining ball

Taper Pins

Fit snugly into tapered holes to secure, position, and align components

Standoffs

Threaded to separate or connect parts as well as position components in assemblies

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Binding Barrels and Screws

Binding Barrels and Screws

Thread together for a low-profile fastener

Rivet Nut Tools

Rivet Nut Tools

Install rivet nuts

Anchor Installation Tools

Anchor Installation Tools

Drive with a hammer to expand and secure anchors in place

Material Handling

Hoist Rings

Pivot to resist stress that would bend or break an eyebolt when lifting at an angle

Eyebolts

Route rope through the loop or attach hooks and shackles for lifting

Eye Nuts

Pair with bolts or threaded rod to lift and hang components

Hooks

Lift, hang, and bind loads with rope and chain

Turnbuckles

Twist the body or end fittings to adjust the length and tension of attached rope and chain

U-Bolts

Anchor heavy pipe, tube, and conduit; stronger than routing clamps and hangers

U-Bolt Plates

Reinforce mounted U-bolts for a more secure hold

Routing Rings

Suspend wire and cable by feeding it through the eyehole

Building and Machinery Hardware

Strut Channel Framing and Fittings

Strut Channel Framing and Fittings

Secure fittings in the U-shaped channel to route conduit and pipe or build other structures

Knobs

Position, tighten, and secure fixtures and equipment

Machine Handles

Machine Handles

Arms give you extra leverage to secure and position jigs, fixtures, and other equipment

Handle Nuts

Attach to threaded shafts to quickly turn the shafts by hand

Cam Handles

For fast clamping, push down on the handle to draw two parts together

Leveling Mount Inserts

Leveling Mount Inserts

Slip onto equipment and furniture to add threaded-stud leveling feet

Fabricating and Machining

T-Slot Nut and Setup Stud Kits

T-Slot Nut and Setup Stud Kits

Mount fixtures of different sizes to your machine table

T-Slot Bolts

Secure clamps and workpieces to machine tables with quicker setup than a T-slot nut and stud

T-Slot Nuts

Combine with setup studs or bolts to mount fixtures to machine tables

Setup Studs

Secure setup clamps and fixtures to your machine table or assemble heavy machines

Clamps

Hold workpieces securely in place

Lathe Chuck Jaw Nuts

Lathe Chuck Jaw Nuts

Secure jaws to a CNC lathe chuck

Power Transmission

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)