About Structural Adhesives
More
About Paint and Protective Coatings
More
Epoxy Structural Adhesives for Harsh Environments
With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions. Epoxies are the strongest structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel, lbs./in. wd. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | Environment | For Joining | Each | |
Adhesives | |||||||||||||
| 1.69 fl. oz. | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (7,000 cP) | -50° to 350° | Amber | Corrosive, Salt Spray, Submersible | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Plastic, Plastic to Rubber, Plastic to Composites, Rubber, Rubber to Composites, Composites | 000000 | 000000 |
| 1.69 fl. oz. | Cartridge | 40 min. | 24 hrs. | Not Rated | Not Rated | 2:1 | Thick Liquid (10,000 cP) | -65° to 350° | White | Corrosive, Salt Spray, Submersible | Metal, Metal to Plastic, Plastic | 000000 | 00000 |
Epoxy Structural Adhesives for Hard-to-Bond Materials
Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these adhesives. They bond dissimilar materials. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.
The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.
Container | Strength | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Includes | Each | |
| 1.69 | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,000 cP) | -50° to 350° | Amber | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Composites, Plastic to Glass, Rubber, Rubber to Composites, Rubber to Glass, Ceramic, Composites, Glass, Wood, Wood to Glass | __ | 000000 | 000000 |
| 1.69 | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,500 cP) | -50° to 350° | Amber | Plastic | 1:1 and 2:1 Mix Ratio Plungers, Mixer Nozzle, One 2-oz. Bottle of Etching Solution | 0000000 | 000000 |
| 1.69 | Cartridge | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,500 cP) | -50° to 350° | Amber | Plastic | 1:1 and 2:1 Mix Ratio Plungers, Mixer Nozzle, Mixing Stick, Two 4-oz. Bottles of Etching Solution, Two Brushes, Two Mixing Trays | 0000000 | 000000 |
| 1.69 | Cartridge | 90 min. | 72 hrs. | Not Rated | Not Rated | 1:1 | Thick Liquid (6,000 cP) | -85° to 270° | Amber | Metal, Metal to Plastic, Metal to Rubber, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Glass, Rubber, Rubber to Glass, Ceramic, Composites, Glass, Wood, Wood to Glass | __ | 000000 | 00000 |
| 48 | Bottle | 30 min. | 24 hrs. | 360 | Not Rated | 2:1 | Thick Liquid (9,000 cP) | -50° to 350° | Amber | Metal, Metal to Plastic, Metal to Rubber, Metal to Composites, Metal to Glass, Plastic, Plastic to Rubber, Plastic to Composites, Plastic to Glass, Rubber, Rubber to Composites, Rubber to Glass, Ceramic, Composites, Glass, Wood, Wood to Glass | __ | 000000 | 000000 |
Flexible Light-Activated Instant-Bond Adhesives
These adhesives stay pliable for flexible bonds that resist cracking. For easy positioning, they begin to harden only when exposed to light.
1700A257 and 2454N1 fluoresce under UV light for easy inspection.
Container | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, fl. oz. | Type | Max. Gap Size Filled | Begins to Harden | Reaches Full Strength | Light Intensity Requirements to Reach Full Strength | Cure Type | Consistency (Viscosity) | Elongation | Temp. Range, °F | Color | For Joining | Each | |
Adhesives | |||||||||||||
| 1.69 | Bottle | 0.25" | 5 sec. | 30 min. | 5 sec. @ 100 mW/cm2 | UV Light | Thin Liquid (850 cP) | Not Rated | 45° to 80° | Clear | Ceramic, Composites, Glass, Metal, Plastic, Rubber | 000000 | 000000 |
Fuel-Resistant Surface Fillers
Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.
1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, pt. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
| 1.5 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 000000 |
| 3 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 00000 |
Surface Fillers for Plastic
Use these two-part fillers to rebuild cracked or worn plastic surfaces. The size listed is the combined total of the two parts.
Surface fillers in a cartridge come with a mixer nozzle, but require a gun (sold separately) for dispensing. For best results, use a primer (sold separately).
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size | Type | Begins to Harden | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | ||||||||||||
| 1.7 fl. oz. | Cartridge | 5 min. | 30 min. | Thick Liquid | 1:1 | 11 sq. in. @ 1/4" | -20° to 180° | Gray | Sand | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 000000 |
Epoxy Potting Compounds for Harsh Environments
Tough enough to be permanently submersed in seawater, these compounds protect sensitive electronics, such as circuit boards, semiconductors, and sensors in harsh environments. They resist moisture, salt, and chemicals, so you can use them in corrosive oil, marine, and mining applications. These compounds can also be used within autoclaves. Because they are epoxies, they are rigid, resist wear, and create excellent electrical insulation. They withstand a wide range of temperatures, and this formulation won’t crack or split as components heat up and cool down.
They come in a cartridge, so you can apply them precisely. To dispense, they require a mixer nozzle and gun (both sold separately).
Dry Time | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Container Size, fl. oz. | Consistency | Touch, hrs. | Overall, hrs. | Hardness Rating | Dielectric Strength, V/mil | Temp. Range, °F | Environment | For Use On | Autoclavable | Each | |
| 1.69 | Thick Liquid | 12 | 24 | Extra Hard | 500 | -50° to 350° | Corrosive, Salt Spray, Submersible | Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PVDF Plastic, Polyimide Plastic, HDPE Plastic, Nylon Plastic, PEEK Plastic, Polyethylene Plastic, UHMW Plastic, Polypropylene Plastic, Glass | Yes | 0000000 | 000000 |
| For Cartridge Size | Each | |
| 1.69 fl. oz. | 00000000 | 000000 |
| For Cartridge Size | Each | |
| 1.69 fl. oz. | 00000000 | 00000 |