We will reply to your message within an hour.
These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.
Connect and disconnect with the power on—spring-loaded contacts open like a switch when separating the connectors, preventing an electrical arc.
Use connectors where ignitable gas and dust may be present, such as in refineries and silos. They also prevent an electrical arc when separating mated connectors so you can safetly connect and disconnect with the power on.
Meet international standards IEC 309-1 and 309-2.
When used together, connectors maintain a watertight and corrosion-resistant NEMA 4X connection.
Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.
Modify your M12 or mini connection to match cords and I/O modules in your system.
Simplify wiring and reduce the number of cords in your automation setup.
Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.
Send higher current than M5, M8, and M12 connectors near tough industrial jobs, such as welding and metal machining.
Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.
Screw these micro M16 connectors together to securely connect equipment.
Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.
Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.
Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.
Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.
Reduce the number of cords needed to send and receive signals where space is tight.
Minimize signal loss between low-current devices with M8 connections.
Connect different pole configurations to join sensors, switches, and other devices to cords, distribution blocks, and I/O modules.
Join two devices with M8 connectors to a single cord, distribution block, or I/O module with M12 connectors to save space and reduce the number of cords in industrial automation setups. Often used with sensors and switches, these splitters send or receive two signals through one connection.
Join M8 connections to M12 connections.
Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.
These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.
These connectors meet MIL-DTL-26482, so they're compatible with other products that meet the same standard. Quickly mate by pushing them together.
Assemble a connector that can handle multiple applications at once. Combine inserts that send power, signal, and data with a base and a hood.
Build a connector that fits in tight spaces by combining male and female inserts for power and signal with a compact base and a hood.
Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.
The smallest latching connectors we offer, these fit in tight spaces. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.
Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. Use them with standard Molex connectors.
Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.
Connectors come assembled with wire leads already installed, so they can be quickly added to existing wiring systems. Use them with AMP MATE-N-LOK connectors.
Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.
Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.
Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.
Attach wires to your circuit board with these Amphenol PV connectors.
Quickly replace or add connectors to an existing wiring system—connectors come assembled with wire leads already installed. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.
Configure a connector for your application by combining housings with pins and sleeves for different wire sizes. Also known as weather-pack connectors, they withstand moisture, harsh engine fluids, and high temperatures.
Connect wires to your circuit board with these Molex KK push-in connectors.
Install these connectors in panels, enclosures, and bulkheads to join equipment with compatible Deutsch-style DC connectors.
Use these connectors in vehicles and other agricultural and construction equipment.
With a PVC housing, connectors withstand exposure to chemicals, oil, fuel, and salt water.
Power hydraulic and air-powered valves, motors, pumps, and pressure switches.
These connectors are designed for use in audio equipment.
Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.
With robot tool mounts and connectors, these vacuum lifters come ready to attach to robot arms with standard ISO mounting hole patterns.