Clear enough to read through, these UV-resistant sealants allow optimal light transmission for use with solar cells and fiber optics. Sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. 3M 730 UV is good for use between dissimilar materials and in environments with wide temperature fluctuation.

Meeting requirements for semiconductor, biomedical, and electronics clean rooms, these sealants won’t contaminate air and surfaces. Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain.

Apply these sealants on wet surfaces and in cold temperatures. They’re non-sagging, so they won't drip from vertical and overhead surfaces.

Sealants with 1,000% elongation can be applied through running water.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. Sealants that are good for joining dissimilar materials also work well in environments with wide temperature fluctuation.

Sealants that cannot be sold to the regions listed are restricted by local chemical regulations, including limits on VOC (volatile organic compounds).

Clear enough to read through, this UV-resistant sealant allows optimal light transmission for use with solar cells and fiber optics. Apply it in cold temperatures, on wet surfaces, and even through running water. The sealant is non-sagging, so it won't drip from vertical and overhead surfaces. It cannot be sold to the regions listed due to local regulatory limits on VOC (volatile organic compounds).

Elongation indicates flexibility—the higher the value is, the more a sealant can stretch. This sealant is good for use between dissimilar materials and in environments with wide temperature fluctuation.

These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility. They’re non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Elongation and joint expansion/compression tolerance indicate flexibility. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint expansion/compression tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Sealants that cannot be sold to California exceed local regulatory limits on VOC (volatile organic compounds).

These non-sagging sealants will not drip while hardening on vertical and overhead surfaces. They’re marine grade, so they stand up to water, corrosion from salt spray, mildew, and UV light.

Sika Sikaflex sealants meet NSF/ANSI 61 safety standards for use with drinking water.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. Sealants that are good for joining dissimilar materials also work well in environments with wide temperature fluctuation.

These sealants don't degrade in sunlight. Also known as glazing compounds, use these sealants to install glass in framing. They’re non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, these sealants are RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance.

Apply these sealants on wet surfaces and in cold temperatures. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Sealants that begin to harden in 3 minutes are ideal for sealing pavement saw cuts made when installing buried sensing wires, also known as detector loops. You can walk or drive over the seams right away because they dry tack free within minutes.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain.

Sealants that cannot be sold to the listed areas exceed VOC (Volatile Organic Compounds) regulations.

Seal joints and gaps in concrete. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

The textured finish matches concrete surfaces. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

Seal concrete joints in high-traffic locations—these sealants stand up to heavy wear and tear, such as steel wheel traffic. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.

When Sika Sikaflex Polyurethane requires a primer, for best results use Primer 260 on metal and Primer 449 on plastic and rubber.

Fix roof leaks in cold and wet conditions. These sealants can even be applied underwater. They're non-sagging, so they won't drip from vertical and overhead surfaces. They are good for use in environments with wide temperature fluctuation.

Elongation indicates flexibility—the higher the value is, the more joint movement a sealant can sustain.

No mixing required—these potting compounds come ready to apply. Use them to encase electronic assemblies for protection from dust, moisture, mechanical shock, and vibration. Softer and more flexible than epoxies and urethanes with the widest temperature range, silicone potting compounds are the best choice for high-temperature applications and electronics exposed to thermal cycling. They have good moisture resistance but poor chemical and abrasion resistance. Silicones provide excellent electrical insulation. They're also known as RTV (room-temperature vulcanizing) compounds because they don’t need heat or UV light to cure.

Potting compounds that meet UL 94 V-0 have passed a test for flame retardance.

Potting compounds that cannot be sold to California exceed local regulatory limits on VOCs (volatile organic compounds). Potting compounds that cannot be sold to Canada are restricted by product labeling requirements.

From shore to sea floor, these potting compounds are formulated for permanent submersion in water—even salt water. Use them to protect circuits and splices in pumps, underwater lighting, and other underwater electronics from corrosion and chemicals. Made of urethane, they withstand a wide range of temperatures, especially cold underwater conditions. They provide good electrical insulation and have excellent flexibility. Since they’re more flexible than epoxy compounds, they’re often used to protect against vibration and impact.

Mix the two parts of these compounds together and pour them over components inside a potting box or other container. If mixing causes air bubbles, put the mixture in a vacuum chamber to remove them.

Make repairs or changes to electrical components after they’ve been potted. While most compounds are permanent, these form a gel that bonds to itself, so you can peel it off without damaging your equipment. Often used in junction boxes, they form a water- and dust-proof seal that’s rated IP68 while also providing excellent electrical insulation. Made of silicone, they withstand a wide range of temperatures and are soft and flexible enough to resist shock and vibration. However, they’re not as strong as permanent potting compounds, so they don’t resist scrapes as well as those made of epoxy and urethane. They’re also not as chemical resistant as epoxy and urethane compounds.

These compounds won’t solidify once you open the container, so you have time to make adjustments when applying them. When removing them from your components, they mostly come off in one piece but there might be some residue left over.

Bottle compounds are a better choice for filling up new enclosures than cartridge compounds because you can pour more in at a time. They have a compartment for each component and require mixing.

Cartridge compounds have a nozzle for precise application. The nozzle can also fit into junction box knockouts, so it’s easier to fill up installed enclosures than it is with bottle compounds. They come ready to use with no mixing required and no waiting time.

These compounds dry quickly when exposed to UV light allowing you to handle the potted items sooner. Made of silicone, they’re softer and more flexible than epoxy or urethane compounds, so they’re better at protecting against shocks and vibration. They also withstand a wider range of temperatures, so they’re often used with electronics that heat and cool rapidly. These compounds are excellent electrical insulators, and they’ll shield your components from moisture and dust. However, they don’t hold up well to abrasion or chemicals. The tapered nozzle lets you apply them precisely.

In just 20 seconds under a UV light, these urethane compounds form into a strong protective layer on electrical components. They withstand a wide range of temperatures and are good electrical insulators. They also stop chemicals, moisture, and dust from damaging your device. With excellent flexibility, they protect against vibration and impact. Since they also work as an adhesive, you can use them to bond and insulate components such as electrical connectors and thermal switches. No mixing required.

Encase electronic assemblies in a layer of urethane for protection from dust, moisture, chemicals, mechanical shock, and vibration. Urethanes withstand a wide range of temperatures and are the best choice for cold-temperature applications. They have excellent flexibility, good chemical and moisture resistance, and provide good electrical insulation.

Cartridge potting compounds can be applied precisely through the included mixer nozzle. You’ll need a dispensing gun (sold separately). US2350™ also require a 4:1 plunger (sold separately) to dispense.

Bottle potting compounds are easier to apply in high volumes than cartridge potting compounds. Mix the compounds together and pour them over components inside potting boxes and other containers. If mixing introduces any air bubbles, put the mixture in a vacuum chamber.

Compounds that cannot be sold to the listed areas are restricted by product labeling requirements.

Tested to meet ASTM E595, a standard used by NASA, these compounds produce almost no volatile emissions that could damage sensitive electronics, even in a vacuum. Light passes through them easily, so they’re ideal for protecting solar cells and fiber optics. Made of silicone, these compounds are softer and more flexible than epoxy and urethane compounds. That means they’re better at protecting against shocks and vibration. They also withstand a wider range of temperatures, so you can use them with electronics that heat and cool rapidly. These compounds are excellent electrical insulators, and they’ll shield your components from moisture and dust. However, they don’t hold up well to chemicals or scrapes. They’re also known as RTV (room-temperature vulcanizing).

These compounds are easy to apply in high volumes. Just mix the two parts together and pour them over components inside a container, such as a potting box.

Clear enough to read through, these UV-resistant potting compounds allow optimal light transmission for use with LEDs, solar cells, and fiber optics. Use them to encase electronic assemblies for protection from dust, moisture, mechanical shock, and vibration. Softer and more flexible than epoxies and urethanes with the widest temperature range, these silicone compounds are the best choice for high-temperature applications and electronics exposed to thermal cycling. They have excellent electrical insulation and good moisture resistance but poor chemical and abrasion resistance. Also known as RTV (room-temperature vulcanizing).

Compounds in a cartridge come with a mixer nozzle for precise application. You need a gun (sold separately) to dispense.

Compounds in a bottle are easy to apply in high volumes. Just mix and pour them over components inside containers, such as potting boxes.

Liquid compounds harden around your component to form a strong, durable, and permanent layer of protection.

Gel compounds form a soft and flexible layer of protection. You can also remove them if you need to re-access your components. They are rated IP68 once potted, so they seal out water even if submersed.

Encase electronic assemblies in a layer of silicone for protection from dust, moisture, mechanical shock, and vibration. Softer and more flexible than epoxies and urethanes with the widest temperature range, silicone potting compounds are the best choice for high-temperature applications and electronics exposed to thermal cycling. They have good moisture resistance but poor chemical and abrasion resistance. Silicones provide excellent electrical insulation. They’re also known as RTV (room-temperature vulcanizing).

Cartridge potting compound requires a gun (sold separately) to dispense; use it with the included mixer nozzle.

Urethane adhesives are the most flexible, so they bond dissimilar materials and damp vibration.

The size listed is the combined total of the two parts. Use 1.64 fl. oz. and 1.69 fl. oz. cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives. Dispense adhesives in 10.1 fl. oz. cartridges with a standard caulk gun.

292 resists moisture and does not require mixing.