Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

A sealed design prevents contamination in dirty and dusty environments.

Customize these dispensers to serve up to 24 lubrication points from a single location.

Serve multiple lubrication points from a single location.

A sealed design prevents contamination in dirty and dusty environments.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

For use in clean environments, these oil reservoirs have multiple air vents that keep pressure balanced.

Flip the lever to start and stop flow.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

Use this dispenser to brush oil on chain, gears, and conveyors. Often used to replenish lubricant after washdowns.

A needle dispensing tip provides fine control for lubricating small parts.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. With a fluoroelastomer seal and a PVDF body, they can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Valves have NPT connections for use with threaded pipe. Turn the handle to adjust the flow of butane, diesel fuel, fuel oil, gasoline, kerosene, natural gas, and propane in small increments.

With no metal parts, these valves are often used for noncontact flow adjustment in wet conditions and harsh environments. All press down on the outside of tubing to adjust flow without contacting the process media.

These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Often used in low-pressure water pipelines, these valves have a plastic body for the lightest weight of our flanged flow-adjustment valves. Use them with water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

Solder these valves to copper tubing for a permanent, leak-tight connection. Use them with water and oil. All gradually open and close to adjust and regulate flow.

For a lightweight and corrosion-resistant alternative to metal valves, these have a plastic body. To create a permanent, leak-tight connection, insert unthreaded pipe into the socket ends and bond with PVC primer and cement. These valves are for use with oil. They gradually open and close to adjust and regulate flow.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.