Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/2 valves.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 4-way and 5/3 closed center valves.

Control these valves with one hand. Also known as 4/2 valves, they create two actions, such as extending and then retracting a double-acting cylinder.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Also known as 4/3 closed-center valves, they create two actions, such as extracting and then retracting a double-acting cylinder.

Create one action with these valves, such as extending a cylinder.

Control six different outputs from a single source of airflow. These valves have one inlet port and six outlet ports. Push in and rotate the dial to move between outlet ports and send airflow to a different output.

The push buttons that operate these valves are separate from the logic unit, allowing you to position them away from machinery. Since both hands are required to simultaneously press the buttons, they protect workers from accidental machinery start-up. They create one action, such as extending a cylinder.

Also known as 4-way and 5/3 pressure center valves, these valves create two actions at the same time, such as extending two single-acting cylinders at once.

Run through equipment cycles up to 30% faster than with standard valves. These valves shift between flow positions in 1.7 ms. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Use a single valve to create motion and control the speed of that motion.

These valves are rated for environments where hazardous material is present. They actuate when voltage is applied to the electrical connection.

With two 3-way integrated solenoid valves, these electrically controlled valves direct airflow to end-of-arm tools that don’t require vacuum suction, such as pick-and-place grippers. Also known as 3/2 valves, each of the two solenoid valves directs air to a different port.

In the off position, these valves stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. They actuate by air signal, so they're good for environments where electrical use may be dangerous.

A simple automation solution that requires no programming, these valves are activated when an object, such as a box rolling on a conveyor, pushes the actuator. They create one action, such as extending a cylinder. Also known as 3-way and 3/2 valves.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Use your foot to operate them, leaving your hands free to perform other tasks. Also known as 4-way and 5/2 valves.

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.

Direct flow with an electronic signal.

Turn the handle to direct flow between ports.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

Divert the flow of compressed air and other media to multiple pieces of equipment. Use with water, oil, air, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

These valves divert flow between ports. Use with water, oil, air, and inert gas.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

With sanitary quick-clamp connections for easy disassembly in systems that require frequent cleaning, these valves are often used to divert flow between ports in food and beverage applications.

Designed to direct the flow of liquids in food, dairy, and chemical-processing facilities, these valves can be fully disassembled for clean-out-of-place (COP) processes.

Lower profile than other solenoid diverting valves and available in smaller pipe sizes, these valves are often used to automatically divert flow between ports in tight spots. Use them with water, oil, air, and inert gas. All operate on electricity.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

Often used in sanitary valve manifolds, these 3-A certified valves can be cleaned in place to eliminate the risk of cross contamination in food, beverage, and dairy lines. All have sanitary quick-clamp fittings for easy disassembly. They operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.