Made with Viton® fluoroelastomer, use these coatings to create a flexible coating on rollers, heavy equipment, and anything else that’s exposed to corrosive chemicals or extreme temperatures. Coatings resist acids, alkalies, fuels, and solvents, as well as temperatures as low as -40° F once cured. They can also be used as an adhesive for Viton® gaskets, O-rings, and seals.

Apply coatings in a bottle and can with a brush or roller. The size listed is the combined total of the two parts.

Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

Water-based epoxy coatings are clear and can be applied over nearly any surface, even old coatings, without altering their appearance. These two-part coatings come with a mixer that attaches to a hand-held drill and a roller cover to apply them once mixed. The size listed is the combined total of the two parts.

Apply gallon-sized water-based coatings with a roller. Coatings that comply with OSHA 29 CFR 1910.22 meet requirements for walking-working surfaces.

Use these coatings in kitchens, furnace areas, and ships on plastic, metal, wood, and masonry. Apply with a brush, roller, or sprayer. The size listed is the combined total of the two parts.

Clear coatings are frequently used on wood—use one coat on sealed wood and two on unsealed. They can be used outside without breaking down, but prolonged exposure to UV light may cause them to yellow.

White coatings are frequently used on walls, ceilings, doors, and stairwells.

Grit in these coatings provides traction and fills hairline cracks. Coatings form a weather- and water-resistant seal to protect and revitalize asphalt surfaces. Apply with a squeegee or brush.

Protect and revitalize asphalt surfaces with these tar-free coatings that form a weather- and water-resistant seal. Apply with a squeegee or brush.

Use these coatings to form a water-resistant layer to restore and reinforce your roof. Apply to a dry surface with a sprayer or brush. They cannot be sold to the listed areas because they exceed local regulatory limits on VOCs (volatile organic compounds).

Made from silicone, these coatings are more durable than acrylic coatings for roofs and have better resistance to pooling water. They reflect up to 90% of the sun's rays to reduce cooling costs. Coatings are self-leveling and have excellent adhesion to most roof surfaces. They begin to protect against rain in as few as 60 minutes after application. Apply to a dry surface with a squeegee or brush.

Reflect at least 85% of the sun's rays to reduce cooling costs. These coatings also restore and reinforce your roof by filling cracks and forming a water-resistant seal. Apply to a dry surface with a brush, roller, or sprayer.

Primer (sold separately) extends the life of the coating. It’s required for use on bare rubberized and aged asphalt roofs.

These coatings reflect up to 60% of the sun's rays. They also restore and reinforce your roof by forming a water-resistant seal. Apply to a dry surface with a sprayer or brush. They cannot be sold to the listed areas due to VOC regulations.

Hide blemishes and protrusions on shingles and flashing. This paint matches common roofing material. It dries quickly to help keep leaves, pollen, and other contaminants from adhering, damaging your finish. Once dry, paint prevents corrosion on flashing and other metal surfaces.

Highly abrasion resistant, use this paint in high-traffic areas. It’s good for marking traffic lanes, parking lots, and factory floors. Paint cannot be sold to the areas listed due to local regulatory limits on VOCs (volatile organic compounds).

Chlorinated rubber paint forms a thicker coating than alkyd paint for better wear and weather resistance.

Thinners cannot be sold to the listed areas due to VOC regulations.

Mark traffic lanes, parking lots, and factory floors.

Alkyd paint dries quickly and can also be used on turf.

Acrylic paint withstands abrasion in high-traffic areas.

Apply paint in a one-gallon can and a five-gallon pail with a brush, roller, or sprayer.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.

Paste fillers resist alkalies, solvents, gasoline, and oil.

Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.

Polyurethane fillers are thin to penetrate deep into cracks. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a standard caulk gun (sold separately). For especially large cracks, use a packer (sold separately) with a grease gun or a grout pump.

Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a dispensing gun (sold separately). The size listed is the combined total of the two parts. A mixer nozzle is included.

Reinforce hot- and cold-applied asphalt patching compounds and coatings with this flexible fabric.

Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.

Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.

Apply acrylic compounds to dry surfaces. Apply asphalt compounds to wet or dry surfaces.

These patching compounds are the most flexible and watertight we offer. Developed for use on flashing, chimneys, and high-stress areas, they are highly vibration resistant.

Dispense compounds in a cartridge in a standard caulk gun (sold separately).

Compounds that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).

Roll out a fast fix for leaky roofs and gutters with these peel-and-stick rolls. Backing is rubberized asphalt adhesive. Roll can be cut to size.

Cut rope to the length you need, pack it in cracks up to 1" wide, and heat with a propane torch (not included). Rope is self-leveling.

These crack fillers come in an easy-to-pour jug for filling cracks in asphalt up to 1/2" wide. They’re ready for traffic in 2 to 5 days.

Spread patching compounds in dry, wet, and even water-filled holes. Compress them with a tamper or shovel and they are immediately ready for traffic.