Also known as GPT cable, this cable is often used in low-voltage applications such as battery and vehicle wiring and radios. It has one red wire and one black wire to easily identify polarity. The wires can be pulled apart for installation.

Often used in mining equipment, submersible pumps, and drilling rigs, this cable withstands 2,000 volts AC/DC. The EPDM insulation resists abrasion, so it can be pulled over rough surfaces without damaging the wires inside.

Often used to wire pendant switches, this cable hangs from an overhead connection. It’s also known as bus drop cable.

The PVC insulation resists abrasion, chemicals, and oil.

Cable with three uninsulated ground wires can be used in wet environments. The ground wires are not counted in the number of wires.

This cable has an insulation with excellent resistance to oil, so it can be used near motors and equipment that require oil lubrication. Often used in automated applications such as robotics and cable carriers, it withstands continuous motion without degrading data or signal transmission. It’s flame rated VW-1 to meet requirements for preventing the spread of flames based on a timed test with vertically suspended material.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of braid that blocks signal interference from nearby equipment and devices.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

This cable meets TC-ER crush and impact requirements for exposed runs in cable carriers, so it can be used without conduit. It withstands periodic flexing and bending, sends signal and data to operate, measure, or regulate automated equipment. The PVC insulation resists oil. It’s flame rated FT4 to meet requirements for preventing the spread of flames based on a timed test with material mounted to a vertical tray.

Use unshielded cable in applications where signal interference is not a concern.

Double shielded cable has a layer of braid and foil shielding that provides excellent protection against signal interference from nearby equipment and devices.

This cable is used in variable-frequency drive motors. It has a layer of braid and foil shielding that provides excellent protection against signal interference caused by voltage fluctuations and current spikes. The industry designation is WTTC, so it can be installed in cable trays or raceway in a wind turbine generator. It’s flame rated FT4 to meet requirements for preventing the spread of flames based on a timed test with material mounted to a vertical tray. The insulation resists oil.

Cable with power wires sends electricity to run a motor.

Also known as festoon cable, this flat cable fits in confined spaces and withstands period flexing and bending, such as in overhead cranes and hoists. Use it to operate, measure, or regulate automated equipment. The PVC insulation resists oil and UV light. It’s flame rated VW-1 to meet requirements for preventing the spread of flames based on a timed test with vertically suspended material.

For technical drawings and 3-D models, click on a part number.

This cable withstands abrasion, oil, and the rough conditions found in welding applications. It’s flame rated VW-1 to meet requirements for vertical flame testing.

Class K cable is for general purpose welding applications. It bends and stays in the position that you bend it.

For technical drawings and 3-D models, click on a part number.

More flexible than standard wire, this wire is often used for internal appliance wiring. The strand count is the number of strands followed by the size of the individual strand. The higher the number of strands, the more flexible the wire. Also known as MTW wire, it’s rated UL 1063 for machine tool wiring.

Flame rated VW-1 wire meets requirements for preventing the spread of flames based on a timed test with vertically suspended material.

Run power over rough surfaces—this wire has thick insulation that stands up to wear and tear. It’s flame rated, which means it meets requirements for preventing the spread of fire. Also known as hook-up wire.

Wire with FEP insulation won’t become brittle from chemicals, and it withstands extreme temperatures, from -90° to 390° F.

Wire with silicone rubber insulation is the most flexible wire we offer. It bends easily around tight turns without cracking.

For technical drawings and 3-D models, click on a part number.

Even at 480° F—hotter than some industrial ovens—this wire’s insulation won’t melt.

Wire with a fiberglass outer and mica inner insulation is the common choice for steel mills, iron mills, and glass manufacturing. You may know it as MG wire. Wire with a silicone-coated outer insulation shields your skin from fiberglass particles when handling the wire.

Wire with a fiberglass outer and PTFE inner insulation won’t corrode from moisture, so it’s often used in industrial drying equipment. It also won’t become brittle or crack from chemicals. This wire is commonly known as TGGT wire.

Wire with a ceramic fabric outer insulation withstands the hottest temperatures of our offering, so you can safely run it near open flames. It’s flame rated VW-1 to prevent the spread of fire. This wire won’t become brittle or crack from chemicals. Bend it and it stays in place.

Connect batteries in vehicles and generators.

Strand count is the number of strands followed by the size of the individual strand.

Wire with a PVC plastic insulation resists fuel and oil.

SAE wire meets standards for low-voltage wiring in vehicle electrical systems.

For technical drawings and 3-D models, click on a part number.

Originally designed to meet the quality standards of the auto industry, this wire withstands high temperatures, flames, and abrasion. Unlike other low-voltage wires, this wire meets strict SAE performance requirements. You'll often hear it referred to as primary wire in trucks, trailers, forklifts, and other vehicles.

In protected environments, such as vehicle interiors, GPT wire is the best choice.

For technical drawings and 3-D models, click on a part number.

Connect batteries in generators, forklifts, and other vehicles in corrosive environments. Also known as marine wire, this copper wire is tin plated to resist corrosion from salt water, battery acid, and oil. Designed for boats, it's a good choice for use outdoors. The PVC insulation stands up to fuel and oil. Strand count is the number of strands followed by the size of the individual strand.

For technical drawings and 3-D models, click on a part number.

Install this copper wire in conduit and cable trays in commercial and industrial buildings. It's also known as branch circuit wire. The outer jacket is designed to be installed without applying pulling lubricant.

Stranded wire is flexible, so it’s pliable enough to be pulled around corners. Wire with a nylon outer insulation resists oil and water. Wire with a polyethylene outer insulation resists abrasion and chemicals. It’s more flexible than nylon insulated wire.

XHHW-2 wire is for dry and wet locations where wire may be exposed to dripping or splashing liquid. THHN wire can be used in dry or damp locations where wire is exposed to condensation or moisture, such as a basement. THWN and THWN-2 wire can be used in both wet and dry environments.

Flame rated VW-1 wire meets requirements for preventing the spread of flames based on a timed test with vertically suspended material.

For technical drawings and 3-D models, click on a part number.

Often used in automated applications such as robotics, this wire withstands continuous motion without degrading data or signal transmission.

Flame rated VW-1 wire meets requirements for preventing the spread of flames based on a timed test with vertically suspended material.

Wire is a UL recognized component.

For technical drawings and 3-D models, click on a part number.

A thick insulation protects this wire from high voltages while maintaining flexibility. The insulation also resists moisture. Often used in automated applications such as robotics, it withstands continuous motion without degrading data or signal transmission. It meets UL 94 V-0 for flame retardance. If this wire is exposed to flames, it minimizes how much smoke and halogen it releases.

For technical drawings and 3-D models, click on a part number.

Insulated with TPE, this wire won’t break down from oil, coolant, or chemicals, and it carries a strong signal even when repeatedly bent. This makes it great for greasy equipment on automated lines, such as lubricated cable carriers. Its insulation also stands up to moisture and sunlight, so you can use this wire outdoors. This wire is flame rated FT1, which means it meets requirements for preventing the spread of fire.

Unshielded wire works in most applications. You can twist it 90° while pulling and bending it at the same time.

Choose shielded wire if you need protection against signal interference from nearby equipment, such as variable frequency drives or small motors. Braid-shielded wire blocks signal interference better than spiral-shielded wire. While it can bend and flex continuously, the shielding may tear if repeatedly twisted. Spiral-shielded wire balances good signal interference and flexibility. It's the most flexible wire we offer, so it will bend, flex, and twist 180° without stretching or snapping.

The EPDM insulation on this wire won’t become brittle or crack from sunlight, humidity, rain, temperature changes, abrasion from dirt and debris, and other rough outdoor conditions. It meets Mine Safety and Health Administration (MSHA) standards for material quality.

DLO wire carries higher voltages than SC wire, making it the better choice for heavy duty applications. Use it to run power to motors, cranes, and other equipment in shipyards, mines, and oil- and gas-drilling rigs. Also known as diesel locomotive cable, this wire was originally designed to wire trains. An inner layer of chlorinated polyethylene plastic (CPE) gives it increased resistance to chemicals, heat, and flames. It’s also rated RHW-2, so it can be used underground and in wet locations.

All are flame rated, so they meets requirements for preventing the spread of flames based on a timed test. FT4 wire is mounted to a vertical tray during testing.

For technical drawings and 3-D models, click on a part number.

Also known as photovoltaic (PV) wire, this wire won’t deteriorate from UV light when used outdoors. Often used in solar panels, the cross-linked polyethylene (XPLE) insulation won’t break down from prolonged exposure to high temperatures. The insulation also resists chemicals. An RHW-2 industry designation means this wire withstands underground and wet locations.

For technical drawings and 3-D models, click on a part number.

Connect equipment and devices to a power supply.

Cords with a NEMA 14-30 or 14-50 plug are often used to power electric vehicles. They have a high current rating.

Cords with a 90° elbow plug fit flush against a wall outlet, so they fit behind machinery or in areas where space is tight.

The insulation on STW and SJTW cords resists water. SRDT cords are for use with high-current equipment, such as ranges and dryers.

Run power to welders in machine shops, garages, and other areas where these cords will be exposed to harsh conditions. These cords have either EPDM or PVC insulation that protects the cord's wires from weld slag and being dragged, kicked, and stepped on. Their insulation also won't crack or become brittle when exposed to oil, water, and weather. They also stay flexible across a wide range of temperatures. A power-indicating light on the socket illuminates when the cord has power.

NEMA 6-50 cords can be used with higher voltage equipment than NEMA 5-15 cords. Use them with portable MIG welders rated up to 400 amps as well as TIG welders, stick welders, and plasma cutters rated up to 250V AC. They have a light that illuminates when they’re grounded safely. A handle makes them easy to plug in and unplug.

Thick insulation protects the internal wires of these cords, so they can be used in high-traffic areas and over rough surfaces. The industry designation is STW, so the insulation resists water.

Cords with a NEMA 14-50 plug and socket have a high current rating and are often used to power electric vehicles. The light on their socket illuminates when the cord has power. Their plug and socket have handles, making them easy to grip when plugging or unplugging them.

Cords with a 90° elbow plug fit flush against a wall outlet, so they fit behind machinery or in areas where space is tight.

For technical drawings and 3-D models, click on a part number.