About Shaft Collars
Shaft collars are useful for holding and positioning components on a shaft. They can also serve as mechanical stops and stroke limiters.
More
About Plain Bearings
More
Oil-Embedded Sleeve Bearings
Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 3/32" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1/4" | 1/4" | 46 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
Oil-Embedded Flanged Sleeve Bearings
Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They’re flanged, so they handle loads both parallel and perpendicular to the shaft. They’re also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
841 Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 3/32" Shaft Dia. | ||||||||||
| 1/4" | 1/4" | 3/8" | 1/16" | 46 lbs. @ 120 rpm | 205 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
Set Screw Shaft Collars
Keep these shaft collars in place by tightening their set screw into the shaft. The tip of the screw digs in for a secure hold, but will mar the shaft’s surface. For maximum holding power, make sure the set screw material is harder than your shaft material. Use these shaft collars to position and retain power transmission components such as sprockets, pulleys, and bearings. You can also use them to limit the movement of a shaft.
Carbon steel collars are strong and wear resistant. Collars with a black-oxide finish have some corrosion resistance, but only in dry environments. Their dark color can be useful for matching other parts in your system. Collars with a zinc-plated finish have an outer layer of zinc that protects the steel from rust and extends the life of the collar. 303 stainless steel collars are corrosion resistant and highly machinable.
316 stainless steel collars are the most corrosion resistant while still being nearly as strong as steel collars. You can expose them to salt water, chlorine solutions, and chemicals without rusting.
Aluminum collars are lightweight and have good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Set Screw | ||||||
|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Wd. | Type | No. Included | Each | |
Black-Oxide 1215 Carbon Steel | ||||||
| 3/32" | 3/8" | 3/16" | Hex Socket | 1 | 000000 | 00000 |
Zinc-Plated 1215 Carbon Steel | ||||||
| 3/32" | 3/8" | 3/16" | Hex Socket | 1 | 0000000 | 0000 |
303 Stainless Steel  | ||||||
| 3/32" | 3/8" | 3/16" | Hex Socket | 1 | 0000000 | 0000 |
316 Stainless Steel | ||||||
| 3/32" | 3/8" | 3/16" | Hex Socket | 1 | 0000000 | 00000 |
6061 Aluminum | ||||||
| 3/32" | 3/8" | 3/16" | Hex Socket | 1 | 000000 | 0000 |
Clamping Shaft Collars
These metal collars are stronger than plastic shaft collars. They clamp evenly around the shaft to create a strong, mar-free hold. To use, slide onto your shaft and tighten the clamping screw to secure.
Black-oxide steel collars have some corrosion resistance. Aluminum collars are lightweight and have good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Clamping Two-Piece Shaft Collars
These metal collars are stronger than plastic shaft collars. The two-piece design allows you to install them anywhere on a shaft without removing components or having access to the ends of the shaft. Collars clamp evenly around the shaft to create a strong, mar-free hold. Tighten the clamping screws to secure.
Black-oxide steel collars have some corrosion resistance. Aluminum collars are lightweight and have good corrosion resistance. 303 stainless steel collars have excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.