Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Block signal interference from nearby devices, such as motors and transmitters, while maintaining a strong, stable connection for M12 threads.

Protect harsh environment M12 connectors when not in use.

Quickly mate these connectors by pushing them together. They're often used with 12 mm proximity switches and valves in automated systems.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Join two connectors that both have internal threads.

Protect harsh environment mini connectors when not in use.

Modify your M12 or mini connection to match cords and I/O modules in your system.

Protect against signal interference while sending 2-3 times more current than M12 connectors.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Minimize signal loss between low-current devices with M8 connections.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.

Send signal and power to low-current devices with M8 connections in food processing and other sanitary applications.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.

Join two devices with M8 connectors to a single cord, distribution block, or I/O module with M12 connectors to save space and reduce the number of cords in industrial automation setups. Often used with sensors and switches, these splitters send or receive two signals through one connection.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

Protect Mil. Spec. connectors when not in use.

Install these connectors in panels, enclosures, and bulkheads to join equipment with compatible Deutsch-style DC connectors.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

One hand is all you need—just push these connectors in to secure them and charge surveillance cameras, user interfaces, and other small devices.

Power robotic arms and other high-amperage machines in motor controls, conveyors, and sorting and packaging systems from your main M35 power line.

Protect your mated connections from moisture and light splashing.

Caps are watertight to protect safe-break plugs when not in use.

Mount these adapters in a panel cutout.

Mount these adapters in a panel cutout.

Connect two DisplayPort cords of the same gender and connection type.

Connect two stereo cords through a panel with these adapters.

Designed to withstand washdown and outdoor environments, these connectors have a seal to block out water and debris.

FDA compliant to safely touch food and threaded for a tight hold, these connectors won’t vibrate loose as they send high-speed data to sensors and other automated devices in food, beverage, and pharmaceutical plants.

Mount these connectors in a panel cutout.

Often used in labs, storage facilities, and offices, the shielding blocks low to moderate signal interference from nearby equipment and devices. These cords have a flange on the socket end to mount them in a panel cutout.

With a flange on the socket end, you can mount these cords in a panel cutout to move data between computers, printers, and mobile devices.

These cords have a Nano M8 connector (also known as a pico connector) on one end and an USB Type-A connector on the other.

Send signal and power to low-current devices with M8 connections near welding, metal machining, and in spots where temperatures change.

With a single cord, these splitters join two devices with M12 connectors to a distribution block or I/O module with M12 connectors. Often used with sensors and actuators, they send signals/power to your devices through one connection.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

Step on or roll carts and platform trucks over these M12 cords without crushing them.

These cords have an M8 connector on one end and an M12 connector on the other.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.

A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

These brass fittings have the strength to handle high-pressure applications.

When space in your pipe line is limited, choose these miniature fittings that are one inch or less in length.

Use these fittings in extreme-pressure conditions up to 15,000 psi.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Connect to CPVC pipe for use in high-temperature plumbing and water supply applications.

Made of polypropylene, these fittings won’t deteriorate when exposed to the damaging effects of ultraviolet light and are suitable to use outdoors. They have the chemical resistance to withstand acids, solvents, and other harsh substances.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

A built-in shut-off valve stops airflow when the fittings are disconnected from tubing.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

Designed for use in welding applications, these fittings are flame retardant.

An all-metal body and built-in tube support or dual seals allow these fittings to handle the highest pressure ratings of all our push-to-connect tube fittings.

Aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Made of acetal, these compression fittings are lighter in weight than metal compression fittings and won’t absorb moisture when used in wet environments.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Lighter in weight than metal quick-disconnect couplings, these couplings are plastic.

With no latch, these couplings have a compact design to fit in small spaces. They can handle pressures up to 700 psi.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push. An internal gripping ring holds the tubing tight.

Fittings can withstand temperatures up to 200° F.

Also known as instant fittings, they connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Use in applications up to 150 psi.

These plastic compression fittings meet NSF/ANSI Standard 51 for food contact.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.