Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Designed for both permanent connections and emergency repairs, use these buckles with banding to create your own low-profile hose clamps.

The end of the band curls back into the buckle—this gives these clamps up to 25% more strength than other low-profile clamps. They are also known as JS-style clamps.

Installing these clamps is a snap—push their interlocking teeth together with your fingers, then squeeze tight with pliers. To remove, use pliers to push sideways and separate the teeth.

Twist the thumb head with your fingers to tighten these clamps. Once tightened, remove the thumb head to minimize your clamp’s profile and make it harder to tamper with.

Not as bulky as our other constant-tension clamps, these round-wire clamps easily fit in cramped spaces. Use in low-pressure applications.

A double ring of thick wire provides a complete seal around large-diameter hose.

These clamps form a 360° seal around your hose or tube to prevent leaks.

These clamps have a wider band than other constant-tension clamps, which provides more coverage and reduces the chance of leaks.

The T-bolt design provides excellent strength and creates a 360° seal. Clamps have a spring that automatically adjusts the clamp diameter when temperatures fluctuate.

One clamp fits a wide range of diameters, so you can always have the right size on hand.

A thumb screw instead of a slotted screw allows you to install these clamps without any tools.

Unlike other pinch clamps, these have a unique tongue-and-groove design that creates a gap-free seal to reduce leaks.

Easy to use, strong, and versatile, these hose clamps are the most common. Tighten their slotted screw with a screwdriver, hex nut driver, or wrench.

Don't worry about your hose and tube expanding and contracting when temperatures fluctuate—these clamps have a Bellville spring that automatically increases and decreases the clamp's diameter.

An extended tail acts as a liner to protect hose and tube from being cut by the slots in the band.

The hose clamps in these assortments have a bolt closure that creates a 360° leak-preventing seal. The clamps have rolled edges, so they won’t cut into hose and tube.

Clamps come packed in a box with individual compartments for each clamp size. To make sure they won’t cut into hose and tube, they have a smooth band with rolled edges.

Create 4" diameter and larger worm-drive clamps that withstand high-temperature applications.

Also known as bridge clamps, these worm-drive clamps align with the spiral support on wire duct hose to provide a tight seal.

Flip the toggle latch to install and remove these clamps in seconds.