We will reply to your message within an hour.
Convert from one square drive size to another.
Push the square drive through the adapter to change size.
These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.
Attach one of these adapters to a socket to turn it with an open-end or box wrench.
Turn sockets with a bit screwdriver.
Extend your socket's reach.
Safely lengthen the reach of your socket while working near flammable vapors and combustible residue.
Safely extend your reach in areas where you could accidentally come into contact with live circuits.
Lock your socket into these extensions to prevent accidental disengagement.
The male ends of these extensions are rounded, so they can pivot to use your tool at an angle.
Bend these socket extensions around obstructions to turn hard-to-reach fasteners.
Pivot the head to access fasteners from an angle.
A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.
Adapters are set to a specific torque and cannot be adjusted.
Set a desired torque within the range.
Change a standard wrench handle into a ratcheting wrench.
Fit these adapters between your wrench and socket to enable finger tightening.
Lock the adapter on your tool and the socket to the adapter to prevent accidental disengagement.
A magnet holds the socket, making changes quicker.
Attach to your socket for a longer reach.
Lock your socket into the extension to prevent accidental disengagement.
Pull the collar to quickly attach and remove sockets.
Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.
Use sockets with tools that accept hex shanks, such as impact drivers and power drills.
Bend these extensions around obstructions to access hard-to-reach fasteners.
First developed for aerospace and automotive assembly processes, these extensions will stand up to your high-volume production and assembly lines.
Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.
Make maximum contact with all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.
The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.
Make maximum contact on all sides of a fastener to reduce slipping. These sockets are also known as torque adapters.
Lock your socket into the extension to prevent accidental disengagement..
Attach these adapters to square-drive tools.
Lock your bit into the adapter to prevent accidental disengagement. These adapters attach to square-drive tools.
Designed to withstand high torque and force, these adapters fit the square drive on impact wrenches. Use with hex-shank bits (also known as insert bits).
Attach conduit to a knockout in an outlet box or enclosure.
Connect different sizes and genders of conduit.
Join different sizes of conduit.
Connect different sizes of conduit.
Attach conduit and armored cable to a knockout in an outlet box or enclosure.
These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.
These adapters provide electromagnetic interference (EMI) protection when connecting shielded flexible plastic conduit to a knockout in an outlet box or enclosure.
Transition between conduit sizes and types.
Transition between types of conduit.
These fittings seal out liquid when used with continuous-flex liquid-tight plastic conduit.
One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.
With more than one channel, this raceway allows you to separate power and data wiring to prevent signal interference.
Close off unused switches and outlets.
Pair wall plates and adapters to create a custom cover for existing receptacles and switches to give them a rejuvenated look, no rewiring required.
Keep switches and outlets under cover for protection from dust and dirt. These stainless steel plates resist corrosion and have a sealing gasket to keep out moisture.
Snap end and center sections together to create your own two-device or wider wall plate.
Give switches and outlets a finished look.
Cover existing outlets and switches for a refreshed appearance, no rewiring necessary.
A large angled opening provides an exit point for cords that run behind walls.
Create various data connector configurations by choosing adapters to snap into the ports in these wall plates.
Add depth to your outlet box.
Close off unused outlets.
Add depth to octagonal outlet boxes.
Add depth to your switch box.
Close off unused switches.
Add depth to your weatherproof outlet box.
Rain, snow, and wet conditions won't damage these corrosion-resistant covers.
These corrosion-resistant covers can withstand rain, snow, and wet conditions without being damaged.
Keep the cover closed during operation to completely shield the outlet and plug from rain, snow, and wet conditions.
Close off unused threaded holes.
Close 2" square holes in the floor of your enclosure with these adhesive plugs.
Sized for knockouts and conduit openings.
Sized for 22 mm and 30 mm push-button holes.
FDA compliant for use near food, these plugs close off unused holes in equipment such as electrical enclosures to keep out debris and water.
A circular groove quickly centers plug in unused holes and knockouts.
Seal unused holes and knockouts in enclosures and outlet boxes.
Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.
These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.
These grips are sized to fit in tight areas.
Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.
Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.
Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.
A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.
Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.
Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.
Snap these cord grips into place to secure cable in wet environments.
Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.
Tighten the screw-down clamp for superior pull-out resistance.
Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.
These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.
Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.
Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.
These grips are the most corrosion resistant of any of our submersible metal cord grips.
Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.
Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.
These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.
Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.
Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.
Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.
Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.
Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.
Stop cords from coming loose in wet environments while keeping them along the side of your enclosure in tight spaces.
With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.
An internal ring keeps cable with braid shielding grounded to the body of the grip to block electromagnetic interference (EMI).
Tighten the screws to secure your cable.
An insert clamps the cable in place to provide more strain relief than other snap-in cord grips for building cable.
The mesh extension provides a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.
These cord grips are lightweight yet durable.
Secure and seal electrical cords entering knockouts at a 45° angle.
Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance.
Able to stand up to rust better than steel grips, these 300 series stainless steel grips secure electrical cables in corrosive environments.
Made of nylon, these grips resist chemicals.
These grips install into enclosure holes quickly to stabilize and relieve strain on cords.
Built with snap-in tabs and a spring extension, these cord grips install into panel holes more quickly than standard grips and better prevent damage from sharp bends.
Connect a single flat cable to a junction box.
These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.
The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.
These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.
Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.
Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.
Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.
Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.
Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.
These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.
These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.
Securely connect cable in sanitary environments such as food plants with these watertight cord grips.
Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.
The cable-entry side has heat-shrinkable polyolefin with an adhesive lining. These are also known as cable-entry seals.
Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.
These grips have a thin, flexible seal that covers the holes until you push cords through.
Adapt metric, NPT, and PG conduit and cord grip threads to match knockout threads.
Mount electrical components along your strut channel to bring power to new locations.
Snap these wall plates onto flush-mount outlet strips to secure the outlet strip in a cutout.
Create a permanent outlet system without opening walls. These outlet strips mount to a wall with clips and hardwire to an existing electrical system.
Use these adapters when the size of a meter face is too small for the DIN cutout in a panel or enclosure.
Conceal live electrical components in circuit breaker boxes to prevent injury and damage.