Stainless Steel Bolts | McMaster-Carr

Filter by

System of Measurement

Thread Size

Length

Material

Fastener Head Type

Threading

Drive Style

Head Height

Thread Type

Thread Direction

Socket Head Profile

Head Width

Head Diameter

Thread Spacing

Thread Pitch

Finish

Specifications Met

Screw Size

Rounded Head Style

Drive Size

DFARS Compliance

REACH Compliance

RoHS Compliance

How can we improve?

35,446 Products

Fastening and Joining

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish

Tighten and loosen by hand without the need for tools

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Carriage Bolts

A smooth head provides a finished look while a square neck keeps the bolt in place when using a nut

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

12-Point Screws

12-Point Screws

12 contact points handle more torque than a hex head while a flange eliminates the need for a washer

Tapping Screws

Fasten a range of materials together without needing to tap the hole first

Pentagon Head Screws

Pentagon Head Screws

Create a tamper-resistant joint with a head than can only be removed with a 5-point socket

Captive Panel Screws

Captive Panel Screws

Secure panels and enclosures while still having access to them

Fastener Assortments

Fastener Assortments

Stay prepared by keeping fasteners in common sizes and materials on hand

Studs

Press, weld, or screw in place to add a threaded fastening point

Elevator Bolts

Create a flush joint to allow movement in tight spaces such as grain elevators and belting systems

Wood Screws

Fasten material to wood or pieces of wood to each other

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

Drywall Screws

Fasten panels of drywall to materials such as wood, metal, and drywall

Binding Barrels and Screws

Binding Barrels and Screws

Thread together for a low-profile fastener

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Standoffs

Threaded to separate or connect parts as well as position components in assemblies

Standoff Caps

Create a finished look on standoffs and protect them from dirt and debris

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Anchors

Secure anything from signs to heavy machinery in concrete, brick, and drywall

Captive Pins

Press into holes in thin materials like panels and circuit boards to permanently join or align them

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Weld Nuts

Weld to metal surfaces to add permanent threads

Rivets

Join materials together permanently, especially when too thin or fragile to fasten with screws

Stud Welders

Join studs and pins to metal, leaving no marks on the back of the material

Power Transmission

Rod Ends

Use with connecting rods to support loads and control steering, tensioning, or pivoting motion

Rod End Nuts

Attach to rods, pipe, and tubing to make pivot and hinge points

Rod End Inserts

Rod End Inserts

Attach to rod ends to increase the amount of misalignment they can handle

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

Lead Screws and Nuts

Lead Screws and Nuts

Components travel along a screw with broad, square threads to clamp and lift heavy loads

Ball Screws and Nuts

Ball Screws and Nuts

Internal ball bearings roll on screws for low friction when moving components at high speeds

Splines and Spline Bearings

Splines and Spline Bearings

Transmit rotary power or move loads along the length of splines

Material Handling

Eyebolts

Route rope through the loop or attach hooks and shackles for lifting

Hoist Rings

Pivot to resist stress that would bend or break an eyebolt when lifting at an angle

Eye Nuts

Pair with bolts or threaded rod to lift and hang components

U-Bolts

Anchor heavy pipe, tube, and conduit; stronger than routing clamps and hangers

Routing Rings

Suspend wire and cable by feeding it through the eyehole

Fabricating and Machining

Setup Studs

Secure setup clamps and fixtures to your machine table or assemble heavy machines

T-Slot Bolts

Secure clamps and workpieces to machine tables with quicker setup than a T-slot nut and stud

T-Slot Nuts

Combine with setup studs or bolts to mount fixtures to machine tables

Building and Machinery Hardware

T-Slotted Framing and Fittings

T-Slotted Framing and Fittings

The most versatile system, attach fittings along the continuous slots to build virtually anything

Door Tracks

Hang panels to slide over openings when there’s not space for a swinging door

Drawer and Cabinet Deadbolt Locks

Drawer and Cabinet Deadbolt Locks

Secure wooden drawers and cabinet doors with a key

Flush Bolt Locks

Flush Bolt Locks

Prevent double doors from being opened, or lock one door while the other stays unlocked

Containers, Storage, and Furniture

Hanging Hooks

Hang tools, hoses, garments, and other supplies on walls for easy access

Facility and Grounds Maintenance

Toilet Mounts

Secure toilet components with flanges and hardware kits

Electrical

Electrical Enclosure Mounts

Electrical Enclosure Mounts

Secure electrical boxes to the floor or a pole

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)