These Grade 5 steel screws are over 70% stronger than our stainless steel wire-lockable hex head screws. Wire these screws together through the hole in the head to get more vibration resistance than any other screw.

Drilled through the head and shaft, these screws vent fluid and gases trapped below the screw, making them good for vacuum applications.

Fasten these screws inside a high-vacuum system without bringing in contaminants.

Stainless steel screws have excellent corrosion resistance in most environments. Wire these screws together for more vibration resistance than other types of socket head screws.

Wedge these hangers in concrete and other solid materials.

The spring holds the washer and toggle against opposite sides of the wall, so everything's in position before you begin tightening. Once tightened, the spring adds vibration resistance.

Drill holes with the point on these hangers.

These screws are drilled through the shaft to vent fluids and gases trapped under the screw. Made from 18-8 stainless steel, they have good chemical resistance and may be mildly magnetic.

Wire these screws together through the hole in the head for better vibration resistance than any other rounded head screw.

To vent fluids and gases trapped under the screw, these metric screws are drilled through the shaft.

These metric set screws are vented to allow fluid and gas to pass through.

Good for general purpose applications where corrosion and high strength aren’t a concern, these rod end bolts are made of carbon steel.

Pivot and hinge components in wet and corrosive environments with these stainless steel or brass rod end bolts.

Also known as swing bolts and eyebolts, these internally threaded rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

Made of stainless steel, these rod end bolts are stronger and more corrosion resistant than our standard flat-shoulder rod end bolts.

Good for general purpose applications where corrosion and high strength aren’t a concern, these rod end bolts are made of carbon steel.

To reduce noise and vibration, these bolts have a rubber bushing—connect them to rods, pipes, tubes, and cable linkages that have female threading. They’re also known as isolated rod ends.

These internally threaded rod ends have an eyelet and a ball that swivels to support angular misalignment. Also known as rod-end bearings.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

Connect your grease gun to the fitting to lubricate.

Connect your grease gun to the fitting to lubricate. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

An oil-embedded bronze insert slowly releases lubricant throughout the life of the rod end.

Made to extremely tight tolerances, these internally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Seals keep out dirt and an oil-embedded foam insert slowly releases lubricant for a long life.

With at least 55° of ball swivel, these rod ends accommodate greater misalignment than any other internally threaded rod end we offer.

Made of cadmium-plated steel, these internally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made of stainless steel, these internally threaded rod ends provide excellent corrosion resistance.

These anodized aluminum rod ends are lighter than stainless steel rod ends and have good corrosion resistance. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

Made of impact-resistant nylon, these internally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These internally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

An innovative body design keeps the ball from being pushed out when supporting thrust loads.

Along with internal threads, these rod ends have a double row of precision ball bearings that allows high speeds and smooth operation.

Also known as nut eyebolts, these are designed for through-hole applications.

Route wire and cable through the smooth eye without snagging.

These eyebolts retain their strength in temperatures as low as -40° F.

Use these eyebolts for routing wire and for other light duty applications.

Also known as screw eyes, use the sharp point of these eyebolts to mount directly into wood.

Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.