About Shaft Collars
Shaft collars are useful for holding and positioning components on a shaft. They can also serve as mechanical stops and stroke limiters.
More
About Ball and Roller Bearings
More
About Plain Bearings
More
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 19mm | 32mm | 8.74mm | Nylon Plastic | Steel | 30 | 290 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Corrosion-Resistant Thrust Ball Bearings
A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 19mm | 32mm | 8.69mm | Nylon Plastic | 410 Stainless Steel | 30 | 200 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 000000 |
Light Duty Dry-Running Flanged Sleeve Bearings
Use where high loads and speeds are not required.
Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Thermoplastic-Blend Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 19mm Shaft Dia. | |||||||||
| 22mm | 23mm | 26mm | 1mm | 550 lbs. @ 60 rpm | 230 lbs. @ 60 rpm | Yellow | -50° to 190° | 00000000 | 00000 |
Washdown Clamping Shaft Collars
Suitable for use in washdown applications, these plastic collars also offer good chemical resistance. They clamp evenly around the shaft to create a strong, mar-free hold. To use, slide onto your shaft and tighten the clamping screw to secure.
Acetal collars have a naturally slippery surface and resist swelling when exposed to moisture.
For technical drawings and 3-D models, click on a part number.
Clamping Screw | White Acetal Plastic | |||||
|---|---|---|---|---|---|---|
| For Shaft Dia., mm | OD, mm | Wd., mm | Type | No. Included | Each | |
| 19 | 40 | 15 | Socket Head Screw | 1 | 00000000 | 000000 |
Quick-Grip Screw-Clamp Bushings
Also known as Trantorque bushings, these tighten with a twist of the collar nut—no screws needed. As you tighten the collar nut, the inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Overall Wd. | Max. Torque, in.-lbs. | Each | |
Steel | |||||
|---|---|---|---|---|---|
| 19mm | 32mm | 29mm | 2,150 | 0000000 | 0000000 |
Flanged Screw-Clamp Bushings
A mounting flange prevents movement during tightening. These bushings are good for shock loads. When you tighten the included screws, the bushing's inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear. They can be mounted on shafts with or without keyways.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | OD | Overall Wd. | Max. Torque, in.-lbs. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
| 19mm | 33mm | 24mm | 1,050 | 42 | Steel | Clamping Screws | 0000000 | 000000 |
Corrosion-Resistant Flanged Screw-Clamp Bushings
Made from stainless steel or plated with nickel, these bushings resist corrosion. A mounting flange prevents movement during tightening. As screw-clamp bushings, they're good for shock loads. When you tighten the clamping screws, the bushing's inner sleeve tightens onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear.
Nickel-plated steel bushings have good corrosion resistance in wet environments. However, the plating may begin to flake with long-term use.
Stainless steel bushings have excellent corrosion resistance and can withstand prolonged exposure to moisture.
For technical drawings and 3-D models, click on a part number.
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Split-Tapered Bushings
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||
|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Each | |
Steel | |||||||
H Style Bushing | |||||||
| 19mm | 1 1/4" | 6mm | 3mm | 3° | 95 | 00000000 | 000000 |