About Ball and Roller Bearings
More
About Plain Bearings
More
One-Piece Thrust Ball Bearings
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
| 1 7/8" | 3 7/32" | 13/16" | Steel | 10,800 | 27,500 | 2,200 | Required | -40° to 245° | Lubrication Hole | 00000000 | 000000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1 7/8" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 2 1/4" | 3/4" | 2,800 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
| 2 1/4" | 2" | 7,500 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2 1/4" | 2 1/2" | 9,350 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2 1/4" | 3" | 11,250 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 220° | 00000000 | 00000 |
Mounted Ball Bearings
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.
Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 7/8" | 2 1/4" | 4 15/16" | 8 1/8" | 2 15/32" | 7/8" | 5/8" | 6 1/4" | 7,850 | 5,200 | 3,500 | -20° to 220° | Self Aligning | Lubricated | 0000000 | 0000000 |
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 7/8" | 2 1/4" | 4 7/16" | 8 1/8" | 2 15/32" | 7/8" | 25/32" | 6 1/4" | 7,850 | 5,200 | 2,500 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 00000 |
Extra-Clearance Mounted Ball Bearings
Keep shafts, such as those with a shoulder, clear of the mounting surface. These bearings have a higher mounting base that gives them more space to the mounting surface than standard mounting bases. All have a set screw for securing them to shafts without having to use a collar. The screw lets shafts rotate in both directions, so they’re good for applications where you need to reverse.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 7/8" | 4 21/64" | 6 1/2" | 8 1/8" | 2 3/4" | 7/8" | 25/32" | 6 1/4" | 7,850 | 5,200 | 2,500 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Easy-Align Mounted Ball Bearings with Two-Bolt Flange
An elongated mounting hole on one side of the flange lets you adjust the position of these bearings without having to remove your shaft. You only need to loosen the bolt instead of removing it to adjust. They’re self-aligning to compensate for shaft misalignment.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Lg. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, ° F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 7/8" | 4 9/16" | 7 7/16" | 2 5/32" | 9/16" | 19/32" | 2 15/16" | 6 3/16" | 7,850 | 5,200 | 2,500 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
2012 Style Bushing | |||||||||
| 1 7/8" | 1 1/4" | 1/2" | 1/4" | 8° | 280 | Steel | Set Screws | 000000000 | 000000 |
2517 Style Bushing | |||||||||
| 1 7/8" | 1 3/4" | 1/2" | 1/4" | 8° | 430 | Steel | Set Screws | 000000000 | 00000 |
3020 Style Bushing | |||||||||
| 1 7/8" | 2" | 1/2" | 1/4" | 8° | 800 | Steel | Set Screws | 000000000 | 00000 |
3030 Style Bushing | |||||||||
| 1 7/8" | 3" | 1/2" | 1/4" | 8° | 800 | Cast Iron | Set Screws | 000000000 | 000000 |
3535 Style Bushing | |||||||||
| 1 7/8" | 3 1/2" | 1/2" | 1/4" | 8° | 1,000 | Cast Iron | Set Screws | 000000000 | 000000 |
Split-Tapered Bushings
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
Bushings with a machine key fit into a matching keyway on a sprocket or pulley for high-torque applications.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||
|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Each | |
Steel | |||||||
Q1 Style Bushing with Machine Key | |||||||
| 1 7/8" | 2 1/2" | 1/2" | 1/4" | 3° | 348 | 00000000 | 000000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
SD Style Bushing | ||||||||
| 1 7/8" | 1 13/16" | 1/2" | 1/16" | 108 | Cast Iron | Clamping Screws, Machine Key | 00000000 | 000000 |
SDS Style Bushing | ||||||||
| 1 7/8" | 1 3/8" | 1/2" | 1/16" | 108 | Cast Iron | Clamping Screws, Machine Key | 00000000 | 00000 |
SF Style Bushing | ||||||||
| 1 7/8" | 2 1/16" | 1/2" | 1/4" | 360 | Steel | Clamping Screws | 00000000 | 00000 |
SK Style Bushing | ||||||||
| 1 7/8" | 1 15/16" | 1/2" | 1/4" | 180 | Steel | Clamping Screws | 00000000 | 00000 |