About Plain Bearings
More
Light Duty Dry-Running Sleeve Bearings
Use where high loads and speeds are not required.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Metric Nylon Bearings | ||||||
|---|---|---|---|---|---|---|
For 42mm Shaft Dia. | ||||||
| 48mm | 50mm | 620 lbs. @ 30 rpm | Off-White | -10° to 220° | 00000000 | 000000 |
High-Load Dry-Running Thrust Bearings
A steel backing adds strength to these slippery PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Temperature Range, °F | Each | |
Steel-Backed PTFE Plastic Bearings | |||||
|---|---|---|---|---|---|
For 42mm Shaft Dia. | |||||
| 66mm | 1.5mm | 7,700 lbs. @ 30 rpm | -320° to 530° F° | 0000000 | 000000 |
Metric Press-Fit Drill Bushings with Head
Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.
Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.
These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD, mm | Lg., mm | OD, mm | Thick., mm | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | Specifications Met | 1-5 | 6-11 | 12-Up | |
42 mm ID | ||||||||||||||
| 55 | 25 | 59 | 5 | 0.025 to 0.05 | 0.02 to 0.039 | -0.2 to 0.2 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 000000 | 000000 | 000000 |
| 55 | 51 | 59 | 5 | 0.025 to 0.05 | 0.02 to 0.039 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 00000 | 00000 | 00000 |
| 55 | 62 | 59 | 5 | 0.025 to 0.05 | 0.02 to 0.039 | -0.3 to 0.3 | H | Steel | Rockwell C61 | DIN 172 | 000000000 | 000000 | 000000 | 000000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
SD Style Bushing | ||||||||
| 42mm | 46mm | 12mm | 3.3mm | 108 | Cast Iron | Clamping Screws | 0000000 | 000000 |
SDS Style Bushing | ||||||||
| 42mm | 35mm | 12mm | 3.3mm | 108 | Cast Iron | Clamping Screws | 0000000 | 00000 |
SK Style Bushing | ||||||||
| 42mm | 49mm | 12mm | 3.3mm | 180 | Steel | Clamping Screws | 0000000 | 00000 |