Bearings for Radial, Thrust, and Moment Loads

Filter by

System of Measurement

Shaft Diameter

For Load Direction

For Housing ID

Width

Bearing Type

Ball Bearing Profile

Bearing Seal Type

Shaft Type

Bearing Construction

Cage Material

Lubrication

Dynamic Thrust Load Capacity

Static Combined Load Capacity

Dynamic Radial Load Capacity

Ring Material

Shaft Mount Type

Material

Dynamic Combined Load Capacity

Bolt Circle Diameter

Static Thrust Load Capacity

Forward

How can we improve?

94 Products

About Ball and Roller Bearings

Open

These bearings have twice as many contact points as angular-contact ball bearings. Fit onto large-diameter hollow shafts to run air and hydraulic lines, electrical wiring, and other components through moving parts in assemblies such as index and rotary tables, packaging equipment, and robotics.

Open bearings dissipate heat more efficiently than shielded bearings.

For technical drawings and 3-D models, click on a part number.

			Radial Load Cap., lbs.		Thrust Load Cap., lbs.		Moment Load Cap., ft.-lbs.
For Shaft Dia.	For Housing ID	Wd.	Dynamic	Static	Dynamic	Static	Dynamic	Static	Max. Speed, rpm	Lubrication	Contact Angle	Temp. Range, °F	ABEC Rating		Each
Steel Ring
Open
2"	2 1/2"	1/4"	510	680	790	1,700	35	60	1,500	Required	30°	-60° to 250°	ABEC-1F	0000000	0000000
2"	2 5/8"	5/16"	750	930	1,100	2,300	50	85	1,500	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
2 1/2"	3"	1/4"	580	830	910	2,050	50	95	1,200	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
2 1/2"	3 1/8"	5/16"	840	1,100	1,250	2,800	70	130	1,200	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
3"	3 1/2"	1/4"	640	990	1,000	2,450	65	130	800	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
3"	3 5/8"	5/16"	930	1,300	1,400	3,350	95	180	1,000	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
3 1/2"	4"	1/4"	700	1,100	1,100	2,850	80	170	700	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
3 1/2"	4 1/8"	5/16"	1,000	1,500	1,550	3,850	120	240	700	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
4"	4 1/2"	1/4"	750	1,250	1,200	3,200	100	220	600	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
4"	4 5/8"	5/16"	1,050	1,750	1,700	4,350	140	310	600	Required	30°	-60° to 250°	ABEC-1F	0000000	000000
5"	5 1/2"	1/4"	850	1,550	1,400	3,950	130	340	500	Required	30°	-60° to 250°	ABEC-1F	0000000	00000000
5"	5 5/8"	5/16"	1,200	2,150	1,950	5,350	200	470	500	Required	30°	-60° to 250°	ABEC-1F	0000000	00000000
6"	6 1/2"	1/4"	950	1,900	1,550	4,700	180	490	300	Required	30°	-60° to 250°	ABEC-1F	0000000	00000000
6"	6 5/8"	5/16"	1,350	2,550	2,200	6,400	260	670	400	Required	30°	-60° to 250°	ABEC-1F	0000000	00000000
7"	7 1/2"	1/4"	1,000	2,200	1,700	5,500	230	660	200	Required	30°	-60° to 250°	ABEC-1F	0000000	00000000

Thin-Profile Crossed-Roller Bearings

For a more compact machine, these bearings have thinner inner and outer rings than high-load crossed-roller bearings. Route hydraulic lines, electrical wiring, and other components through the inside of the bearing. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open bearings dissipate heat more efficiently than sealed bearings.

Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

For technical drawings and 3-D models, click on a part number.

				Combined Load Cap., lbs.
For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	Features		Each
Open
10	21	5	Steel	250	180	1,000	Required	0° to 175°	Lubrication Hole	0000000	0000000
15	26	5	Steel	290	240	1,000	Required	0° to 175°	Lubrication Hole	0000000	000000
20	31	5	Steel	310	290	2,900	Required	0° to 230°	__	0000000	000000
30	41	5	Steel	390	440	2,100	Required	0° to 230°	__	0000000	000000
40	51	5	Steel	440	560	1,600	Required	0° to 230°	__	0000000	000000
50	61	5	Steel	510	710	1,300	Required	0° to 230°	__	0000000	000000
60	71	5	Steel	590	910	1,200	Required	0° to 175°	Two Lubrication Holes	0000000	000000
70	81	5	Steel	630	1,050	1,050	Required	0° to 175°	Two Lubrication Holes	0000000	000000
80	91	5	Steel	680	1,200	900	Required	0° to 175°	Lubrication Hole	0000000	000000
90	101	5	Steel	710	1,350	800	Required	0° to 175°	Lubrication Hole	0000000	000000
100	111	5	Steel	750	1,450	750	Required	0° to 175°	Lubrication Hole	0000000	000000
Sealed
50	66	8	Steel	1,100	1,600	700	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
60	76	8	Steel	1,250	1,950	500	Lubricated	0° to 175°	Lubrication Groove, Lubrication Hole	0000000	000000
70	86	8	Steel	1,300	2,200	510	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
80	96	8	Steel	1,400	2,500	460	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
90	106	8	Steel	1,500	2,750	375	Lubricated	0° to 175°	Lubrication Groove, Lubrication Hole	0000000	000000
100	116	8	Steel	1,600	3,100	350	Lubricated	0° to 175°	Lubrication Groove, Lubrication Hole	0000000	000000
110	126	8	Steel	1,650	3,350	300	Lubricated	0° to 175°	Lubrication Groove, Lubrication Hole	0000000	000000
120	136	8	Steel	1,750	3,700	275	Lubricated	0° to 175°	Lubrication Groove, Lubrication Hole	0000000	000000
130	146	8	Steel	1,750	3,950	290	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
140	156	8	Steel	1,850	4,250	270	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
150	166	8	Steel	1,950	4,600	250	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
160	186	13	Steel	5,200	10,050	230	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
170	196	13	Steel	5,250	10,400	220	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
180	206	13	Steel	5,500	11,150	205	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
190	216	13	Steel	5,550	11,550	195	Lubricated	0° to 175°	Four Lubrication Holes	0000000	000000
200	226	13	Steel	5,800	12,250	175	Lubricated	0° to 175°	Lubrication Groove, Lubrication Hole	0000000	00000000

High-Load Face-Mount Crossed-Roller Bearings

With thicker inner and outer raceways, these bearings can handle heavier loads than thin-profile crossed roller bearings. Mounting holes on the inner and outer rings allow for fastening onto hollow joints and shafts. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open bearings dissipate heat more efficiently than sealed bearings.

Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

For technical drawings and 3-D models, click on a part number.

				Combined Load Cap., lbs.
For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	Features		Each
Open
10	52	8	Steel	650	540	2,400	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	0000000
20	70	12	Steel	1,700	1,850	1,600	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
25	80	12	Steel	1,900	2,350	1,400	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
35	95	15	Steel	3,850	4,650	1,100	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
55	120	15	Steel	4,500	6,200	850	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
80	165	22	Steel	11,400	16,100	600	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
90	210	25	Steel	16,500	24,200	500	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
115	240	28	Steel	18,950	31,000	400	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	00000000
160	295	35	Steel	23,350	38,850	350	Lubricated	0° to 175°	Lubrication Groove, Two Lubrication Holes	0000000	00000000
210	380	40	Steel	35,050	63,150	260	Lubricated	0° to 175°	Lubrication Groove, Two Lubrication Holes	0000000	00000000
Sealed
10	52	8	Steel	650	540	1,900	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
20	70	12	Steel	1,700	1,850	1,300	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
25	80	12	Steel	1,900	2,350	1,100	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
35	95	15	Steel	3,850	4,650	900	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
55	120	15	Steel	4,500	6,200	650	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
80	165	22	Steel	11,400	16,100	450	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
90	210	25	Steel	16,500	24,200	400	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	00000000
115	240	28	Steel	18,950	31,000	300	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	00000000
160	295	35	Steel	23,350	38,850	350	Lubricated	0° to 175°	Lubrication Groove, Two Lubrication Holes	0000000	00000000
210	380	40	Steel	35,050	63,150	260	Lubricated	0° to 175°	Lubrication Groove, Two Lubrication Holes	0000000	00000000

High-Load Crossed-Roller Bearings

The thicker inner and outer raceways on these bearings can handle heavier loads than the thin-profile crossed-roller bearings. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open bearings dissipate heat more efficiently than sealed bearings.

Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

For technical drawings and 3-D models, click on a part number.

				Combined Load Cap., lbs.
For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F	Features		Each
Open
30	55	10	Steel	1,700	1,850	1,750	Required	0° to 245°	__	0000000	0000000
40	65	10	Steel	1,900	2,350	1,400	Required	0° to 245°	__	0000000	000000
50	80	13	Steel	3,850	4,650	1,150	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
60	90	13	Steel	4,200	5,450	1,000	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
70	100	13	Steel	4,500	6,200	880	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
80	120	16	Steel	7,200	9,700	750	Required	0° to 230°	Lubrication Groove, Two Lubrication Holes	0000000	000000
90	130	16	Steel	7,400	10,500	680	Required	0° to 245°	__	0000000	000000
100	150	20	Steel	11,400	16,200	600	Required	0° to 245°	__	0000000	000000
110	160	20	Steel	11,750	17,400	550	Required	0° to 245°	__	0000000	000000
120	180	25	Steel	16,500	24,250	500	Required	0° to 245°	__	0000000	000000
Sealed
20	36	8	Steel	650	540	2,100	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
30	55	10	Steel	1,700	1,850	1,400	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
40	65	10	Steel	1,900	2,350	1,100	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
50	80	13	Steel	3,850	4,600	900	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
60	90	13	Steel	4,200	5,400	800	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
70	100	13	Steel	4,500	6,200	700	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
80	120	16	Steel	7,200	9,700	600	Lubricated	0° to 210°	Lubrication Groove, Two Lubrication Holes	0000000	000000
90	130	16	Steel	7,400	10,500	540	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
100	150	20	Steel	11,400	16,200	480	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
110	160	20	Steel	11,750	17,400	440	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
120	180	25	Steel	16,500	24,250	400	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	000000
200	260	25	Steel	20,700	37,950	260	Lubricated	0° to 245°	Lubrication Groove, Two Lubrication Holes	0000000	00000000

Thin-Profile Face-Mount Crossed-Roller Bearings

With thinner inner and outer rings, these bearings keep your machines more compact than high-load crossed-roller bearings. Route hydraulic lines, electrical wiring, and other components through the inside of the bearing. Mounting holes on the rings allow for fastening onto hollow joints and shafts. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

For technical drawings and 3-D models, click on a part number.

				Combined Load Cap., lbs.
For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Ring Material	Dynamic	Static	Max. Speed, rpm	Lubrication	Temp. Range, °F		Each
Open
10	43	5	Steel	330	310	2,800	Lubricated	0° to 210°	0000000	0000000
20	53	5	Steel	420	480	2,050	Lubricated	0° to 210°	0000000	000000
30	63	5	Steel	480	610	1,600	Lubricated	0° to 210°	0000000	000000
40	73	5	Steel	540	780	1,300	Lubricated	0° to 210°	0000000	000000

Thin-Profile Maintenance-Free Turntable Bearings

At 16 mm tall, these bearings are about the height of your typical plastic water bottle cap, so they won’t bulk up your builds. They handle radial, thrust, and moment loads. Often used to oscillate heavy equipment, find them rotating hoists or spinning components on robotic arms. The internal sleeve moves smoothly and will never require lubrication. For easy alignment and mounting, these bearings have holes on both the inner and outer ring. They’re also known as slewing-ring bearings.

Note: Listed capacities only apply when bearings are mounted parallel to the ground. Otherwise, they reduce when bearings are tilted.

For technical drawings and 3-D models, click on a part number.

Thrust Load Cap., lbs.		Radial Load Cap., lbs.							Bearing
Dynamic	Static	Dynamic	Static	Static Moment Load Capacity, ft.-lbs.	OD, mm	ID, mm	Overall Ht., mm	Material	Type	Material	Plain Bearing Type	Mounting Fasteners Included		Each
For Combined Radial, Thrust, and Moment Loads
670	2,650	160	560	140	110	50	16	Anodized Aluminum	Plain	PTFE Plastic	Sleeve	No	0000000	0000000
890	3,100	200	670	180	120	60	16	Anodized Aluminum	Plain	PTFE Plastic	Sleeve	No	0000000	000000
1,100	4,450	330	330	330	160	100	16	Anodized Aluminum	Plain	PTFE Plastic	Sleeve	No	0000000	000000
1,650	6,050	420	1,450	470	210	150	16	Anodized Aluminum	Plain	PTFE Plastic	Sleeve	No	0000000	000000
2,000	7,850	560	1,750	640	260	200	16	Anodized Aluminum	Plain	PTFE Plastic	Sleeve	No	0000000	000000
2,650	10,750	780	2,200	880	360	300	16	Anodized Aluminum	Plain	PTFE Plastic	Sleeve	No	0000000	00000000

Email Us

About Ball and Roller Bearings

Ultra-Thin Ball Bearings

Thin-Profile Crossed-Roller Bearings

High-Load Face-Mount Crossed-Roller Bearings

High-Load Crossed-Roller Bearings

Thin-Profile Face-Mount Crossed-Roller Bearings

Thin-Profile Maintenance-Free Turntable Bearings