12,850 lbs. Dynamic Radial Load Capacity Bearings

Filter by

Mounted Bearing Type

Bearing Type

Housing Material

System of Measurement

Mounting Hole Center-to-Center

Shaft Mount Type

Shaft Diameter

Overall Length

ABEC Rating

Alignment Style

Bearing Material

Bearing Seal Type

DFARS Compliance

Grease Fitting Included

Grease Fitting Thread Type

Lubricant

Lubrication

Maximum Temperature

Minimum Temperature

Misalignment Capability

Overall Height

Overall Width

Dynamic Radial Load Capacity

Forward

How can we improve?

4 Products

About Ball and Roller Bearings

Mounted Ball Bearings

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.

Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.

Bearing with concentric lock use adapter sleeves (sold separately) to lock onto shafts in a way that enables high running speeds with little vibration. They work for applications that require reversing because they allow shafts to rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Bearings

With Set Screw

With Concentric Lock

		Overall			Mounting			Radial Load Cap., lbs.
For Shaft Dia.	Center Ht.	Ht.	Lg.	Wd.	Hole Lg.	Hole Wd.	Hole Ctr.-to-Ctr.	Dynamic	Static	Max. Speed, rpm	Temp. Range, °F	Alignment Style	Lubrication		Each
Sealed Steel Bearings with Cast Iron Housing
Shaft Mount Type: Concentric Lock
60mm	76.2mm	151mm	265mm	70.8mm	35mm	25mm	203mm	12,850	8,950	3,000	-20° to 210°	Self Aligning	Lubricated	00000000	0000000
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing
Shaft Mount Type: Set Screw
2 1/2"	3"	5 29/32"	10 7/16"	2 15/16"	1 3/16"	31/32"	8"	12,850	9,000	2,000	0° to 210°	Self Aligning	Lubricated	0000000	000000

Adapter Sleeves for Bearings with Concentric Lock

Adapter Sleeve

Make up for imperfections and gaps between your bearing and shaft for a tight fit. These bearing adapter sleeves are the most common way to mount a bearing with a tapered bore onto a cylindrical seat. They work with both straight and stepped shafts. Secure using the included lock nut.

Low-Carbon Steel
For Shaft Diameter, mm	ID, mm	Width, mm	Includes		Each
60	60	65	Lock Nut, Lock Washer	00000000	0000000

Mounted Ball Bearings with Four-Bolt Flange

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Bearings

Set Screw Mount

	Overall				Mounting		Radial Load Cap., lbs.
For Shaft Dia.	Ht.	Lg.	Wd.	Flange Thick.	Hole Dia.	Hole Ctr.-to-Ctr.	Dynamic	Static	Max. Speed, rpm	Temp. Range, °F	Alignment Style	Lubrication		Each
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing
Shaft Mount Type: Set Screw
2 1/2"	7 3/8"	7 3/8"	2 3/4"	7/8"	43/64"	5 55/64"	12,850	9,010	2,000	0° to 210°	Self Aligning	Lubricated	0000000	0000000