Use for pressures up to 200 psi. Also known as insert fittings, these slide into semi-flexible plastic pipe and secure with a clamp.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Use at pressures up to 4,300 psi.

The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

The male pipe threads on these fittings have a sealant applied for extra protection against leaks.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Connect stainless steel tubing on one end and plastic tubing on the other end.

Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket between them. The flanges’ sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than other high-vacuum fittings with rubber gaskets.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Solder these fittings to tubing for a permanent, leak-tight connection. They are also known as sweat fittings.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

With a nickel-plated finish, these compression fittings resist corrosion better than plain brass fittings.

The sleeve in these fittings is rubber instead of metal, so it cushions the tubing and absorbs vibration while creating a tight seal.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Choose these metal fittings when you need better durability than our plastic push-to-connect fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

Thicker walls make these fittings—sometimes called flareless or bite fittings—withstand about twice as much pressure as standard compression fittings, so they’re good for hydraulic power applications.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight seal on tubing that is flared to 37°.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

A built-in shut-off valve stops airflow when the fittings are disconnected from tubing.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Connect high-pressure brake lines with fittings that won’t crack in frigid temperatures. Often used on commercial trucks and trailers, these fittings meet Department of Transportation FMVSS 571 safety standards.

Withstanding up to 300° F, these fittings have the highest temperature rating of all our brass push-to-connect tube fittings for air and water.

Designed for use in welding applications, these fittings are flame retardant.

Barbs grip onto tubing.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Monitor flow with these clear fittings.

Aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

Color-code fittings for easy identification. These aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Safe for use in your air brake line, these fittings meet Department of Transportation FMVSS 571 standards. They’ve been tested for thermal cycling, vibration, and burst pressure, so put them to work right away.

Made of acetal, these compression fittings are lighter in weight than metal compression fittings and won’t absorb moisture when used in wet environments.

Made of stainless steel, these fittings are more durable than plastic barbed tube fittings for food and beverage.

Made of FDA listed materials, these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Also known as instant fittings, these connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Use in applications up to 150 psi.

Made of PVDF (also known as Kynar), these fittings have excellent strength and can handle temperatures as high as 240° F or 270° F.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Connect these fittings to tubing with a ring and a crimping tool (both sold separately). Safe to use with drinking water, these fittings meet the strict standards of NSF/ANSI 61.

Fittings have a barb that grips onto tubing. Use in applications up to 120 psi.

Fittings are 316 stainless steel, which has excellent chemical resistance and is more durable than plastic.

Fittings have a barb that grips onto tubing. Use in applications up to 150 psi.

Metal hose fittings have better durability than plastic barbed hose fittings.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Metal cam-and-groove couplings have better durability than plastic cam-and-groove couplings.

A single rounded bead grips onto hose just like a barb, but has no sharp edges that could cut or damage soft hose. Slide the beaded end into hose and secure with a clamp. Use in coolant applications up to 300 psi.

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

Made of stainless steel, these hose fittings are more durable than plastic barbed hose fittings and have excellent corrosion and chemical resistance. Slide the barbed end into hose and secure with a clamp.

To stand up to the harsh chemicals used to clean food-processing lines, these fittings are made of PVDF, also known as Kynar.

Plastic provides a lightweight and economical alternative to metal. All valves have barbs that grip onto tubing for a secure hold. They’re for use with water, oil, air, and inert gas.

Flip the toggle to quickly turn these valves on and off. All have threads and a hex nut below the handle for installation in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Insert tubing into the push-to-connect fittings on these valves—no heat, solder, or flux required. They meet NSF/ANSI 51 for safe use with food.

For chemical-processing applications in confined areas, these valves have a low-profile handle to fit in tight spots. A rubber seal and a plastic body stand up to aggressive, corrosive solutions.

With 45° flared tube fittings, these valves form a tight seal on metal tubing. Use with air. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a low-profile body and a narrow port-to-port length, these valves fit in tight spots. Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.