These carriages and guide rails are steel.

A black chrome plating diffuses light, preventing reflecting light from causing equipment to malfunction.

Designed for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

Adapt most 15 mm guide rails to fit on T-slotted assemblies.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Use these carriages and guide rails for light loads where precise movement is not required.

Support loads while guiding and positioning work with these steel rollers and guide rails.

Slides have a row of ball bearings on each side of the rail.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

Made with two pieces, these shaft supports secure your shaft parallel to your mounting surface and make it easy to access the shaft without having to slide it out or uninstall the support. Use these supports when working with light to medium loads where shaft alignment is not critical.

Create a support that fits the exact dimensions of your shaft to brace it along a flat surface. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

A removable collar allows access to the shaft without unbolting the flange. For use with light to medium loads where shaft alignment is not critical, these supports allow you to hold linear shafts perpendicular to the mounting surface. Secure the shaft by tightening the clamping screw.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

For your compliance and quality assurance needs, these shafts come with a material certificate with a traceable lot number.

From one compact system, transmit linear or rotary motion or both at once (sometimes called spiral motion). Because of these different motions, these ball screw/splines and bearings create efficient, fluid movements in complex automated applications, such as pick-and-place robots.

No need to turn a knob or pull a handle—these slides open a drawer with a light push.

Drawers roll closed quietly and pull out completely, keeping your space quiet and the contents of the drawer accessible. To give you access to items at the back of the drawer, these slides extend a full inch past your cabinet.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

The stacked design provides stability for deep and wide drawers.

Where vibration or movement could force your drawer open, these slides have a spring that pulls and holds it shut. As your drawer approaches the closed position, the spring finishes the job.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

A lever locks the drawer in place whether it’s open or closed; push the lever to release the lock.

When you don't have enough clearance for side-mount or under-the-counter slides, mount these to the base of your drawer.

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.