About Paint and Protective Coatings
More
Enclosure Paint
Touch up scratches and wear on your enclosure with paint that matches its color. This acrylic lacquer paint has strong adhesion and resists detergent and water—including in washdown environments—as well as abrasion, heat, and alcohol. It sprays evenly onto surfaces, with no need for additional tools such as brushes.
Dry Time | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Container Net Weight, oz. | Composition | Touch, min. | Overall, days | Approximate Coverage @ Thickness | Spray Position | Maximum Temperature, °F | For Use On | Color (Appearance) | Color Code | Cannot Be Sold To | Each | |
Acrylic Lacquer | ||||||||||||
| 10 1/2 | Solvent Based | 8 | 7 | 28 sq. ft. @ 1 mil | Upright | 100° | Steel, Stainless Steel | Gray (Gloss) | ANSI 61 | CA | 00000000 | 000000 |
Water-Resistant Surface Fillers
Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.
Putty fillers come in a stick with a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.
Container | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Net Weight, oz. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Approx. Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Specifications Met | Each | |
Loctite® Fixmaster Metal Magic Steel | ||||||||||||||
| EA 3463 | 4 | Stick | 3 | 24 hrs. | Putty | 10 sq. in. @ 1/4" | 1" | -20° to 250° | Gray | Sand | Bronze, Copper, Steel, Stainless Steel, Cast Iron, Concrete | NSF/ANSI 61 | 0000000 | 000000 |
Surface Fillers for Metal
Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal. The size listed is the combined total of the two parts.
NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
Container | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Mfr. Model No. | Net Weight | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Specifications Met | Finishing Method | For Use On | Each | |
Devcon Stainless Steel Putty | ||||||||||||||
| 10270 | 1 lbs. | Jar, Can | 60 | 16 | Putty | 11:1 | 50 sq. in. @ 1/4" | -40° to 250° | Dark Gray | NSF/ANSI 61 | Machine, Drill, Sand, Saw, Tap | Stainless Steel | 00000000 | 0000000 |
Surface Fillers | ||||||||||||||
| __ | 4 oz. | Stick | 3 | 24 | Putty | __ | 16 sq. in. @ 1/4" | -40° to 250° | Copper | NSF/ANSI 61 | Drill, Sand, Saw | Brass, Bronze, Copper | 0000000 | 00000 |
| __ | 4 oz. | Stick | 3 | 24 | Putty | __ | 16 sq. in. @ 1/4" | -40° to 250° | Dark Gray | NSF/ANSI 61 | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
High-Pressure Leak-Repair Sticks for Metal
To stop leaks in metal tanks and equipment without draining the contents, heat the area with a heat gun or torch to melt the stick and form a permanent seal. The resulting patch can withstand pressure up to 600 psi. These sticks meet NSF/ANSI 61 safety standards for use with drinking water systems.
| Container Net Weight, oz. | Begins to Harden, min. | Reaches Full Strength, sec. | Temp. to Begin to Harden, °F | Consistency | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Specifications Met | Finishing Method | For Use On | Each | |
| 0.375 | 1 | 90 | 250 | Putty | 1/8" | Yes | Not Rated to 350° | Green | NSF/ANSI 61 | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
Surface Fillers for Plastic
Use these two-part fillers to rebuild cracked or worn plastic surfaces. The size listed is the combined total of the two parts.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. Use with most rigid and semi-rigid types of plastic. They meet NSF/ANSI 61 for use with drinking water.
Container | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Net Weight | Type | Begins to Harden | Reaches Full Strength | Consistency | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | |||||||||||
| 4 oz. | Stick | 20 min. | 24 hrs. | Putty | 16 sq. in. @ 1/4" | -40° to 250° | Off-White | Drill, Sand, Saw | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic | 0000000 | 000000 |