Extended-Reach Air Nozzles
The extra length allows access into hard-to-reach areas.
For technical drawings and 3-D models, click on a part number.
Air Inlet | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Lg. | Pipe Size  | Thread Type | Gender | Air Consumption | Max. Temp., °F | Volume | Tip OD | Max. Inlet Pressure, psi | Material | Each | ||
| D | 6" | 1/8 | NPT | Male | 35 cfm @ 100 psi | 140° | 103 dBA @ 100 psi | 3/16" | 120 | Brass | 0000000 | 00000 |
| D | 12" | 1/8 | NPT | Male | 35 cfm @ 100 psi | 140° | 103 dBA @ 100 psi | 3/16" | 120 | Brass | 000000 | 0000 |
| D | 18" | 1/8 | NPT | Male | 35 cfm @ 100 psi | 140° | 103 dBA @ 100 psi | 3/16" | 120 | Brass | 0000000 | 00000 |
Right-Angle Wide-Airflow Air Nozzles
Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles. All conform to OSHA 29 CFR 1910.242 requirements for maximum air outlet pressure.
For technical drawings and 3-D models, click on a part number.
Tip | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Air Consumption | Max. Temp., °F | Volume | Wd. | Thick. | O'all Lg. | Max. Inlet Pressure, psi | Specifications Met | Each | |
1/8 NPT Male | |||||||||
Zinc | |||||||||
| 15 cfm @ 100 psi | 155° | 84 dBA @ 80 psi | 15/16" | 3/16" | 15/16" | 145 | OSHA Compliant 29 CFR 1910.242 | 0000000 | 000000 |
316L Stainless Steel | |||||||||
| 14 cfm @ 100 psi | 750° | 81 dBA @ 80 psi | 15/16" | 3/16" | 11/16" | 145 | OSHA Compliant 29 CFR 1910.242 | 0000000 | 000000 |
1/8 BSPP Male | |||||||||
Zinc | |||||||||
| 13 cfm @ 85 psi | 155° | 84 dBA @ 80 psi | 15/16" | 3/16" | 15/16" | 145 | OSHA Compliant 29 CFR 1910.242 | 0000000 | 00000 |
Right-Angle Food Industry Wide-Airflow Air Nozzles
Air blows out of these nozzles in a wide pattern at a 90° angle from the inlet, distributing air over a wider area than focused-airflow nozzles. They’re FDA compliant 21 CFR 110.40 for use in the food industry. All conform to OSHA 29 CFR 1910.95 requirements for noise.
For technical drawings and 3-D models, click on a part number.
Tip | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Air Consumption | Max. Temp., °F | Volume | Wd. | Thick. | O'all Lg. | Max. Inlet Pressure, psi | Specifications Met | Each | |
1/8 NPT Male | |||||||||
316 Stainless Steel | |||||||||
| 10 cfm @ 75 psi | 1000° | 84 dBA @ 80 psi | 1" | 1/8" | 3/4" | 435 | FDA Compliant 21 CFR 110.40, OSHA Compliant 29 CFR 1910.95 | 0000000 | 000000 |
1/8 BSPP Male | |||||||||
316 Stainless Steel | |||||||||
| 10 cfm @ 75 psi | 1000° | 84 dBA @ 80 psi | 1" | 1/8" | 3/4" | 435 | FDA Compliant 21 CFR 110.40, OSHA Compliant 29 CFR 1910.95 | 0000000 | 00000 |
Plastic-Body Blowguns
The lightweight plastic construction makes these blowguns more comfortable to hold than metal. They have an angled nozzle that can direct air over and around obstacles. Pull the trigger to adjust the airflow rate from a puff to a blast. Volume (dB) is measured 3 ft. from the blowgun at 100 psi.
Tapered nonmarring nozzle tips won’t damage your workpiece.
All safety nozzle tips have holes around the circumference so air can escape if the nozzle is blocked.
Safety nozzle tip cannot be removed once installed on a blowgun.
Safety nozzle tip with chip guard creates an air curtain around the airstream to deflect flying chips and dust.
High-flow nozzle tip amplifies the airflow to double that of other nozzles. It cannot be removed once installed on a blowgun.
Chip shield fits over the blowgun nozzle to protect the user from flying debris.
Guns used with tips that meet OSHA 29 CFR 1910.242 will conform to requirements for maximum air outlet pressure.
| Dia. | Volume, dB | Specifications Met | Material | Each | |
Tapered Nonmarring | |||||
|---|---|---|---|---|---|
| 1/2" | 98 | __ | Rubber | 0000000 | 00000 |
| 1" | 98 | __ | Rubber | 0000000 | 00000 |
| 1 5/16" | 98 | __ | Rubber | 0000000 | 00000 |
Safety | |||||
| 1/2" | 94 | OSHA Compliant 29 CFR 1910.242 | Aluminum | 0000000 | 00000 |
Safety with Chip Guard | |||||
| 1/2" | 86 | OSHA Compliant 29 CFR 1910.242 | Aluminum | 0000000 | 00000 |
Low-Noise Safety | |||||
| 13/16" | 82 | OSHA Compliant 29 CFR 1910.242 | Acetal Plastic | 0000000 | 00000 |
High Flow | |||||
| 9/16" | 95 | OSHA Compliant 29 CFR 1910.242 | Aluminum | 0000000 | 00000 |
| OD | Material | Each | |
| 4" | Plastic | 00000000 | 00000 |
Blowguns with Nonmarring Tip
The rubber tip won't damage your workpiece.
Blowguns with angled nozzle can direct air over and around obstacles.
Blowguns | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Air Inlet | Replacement Nozzles | ||||||||||||
| Nozzle Lg. | Air Consumption | Volume | Max. Inlet Pressure, psi | Pipe Size | Thread Type | Gender | Body Material | Nozzle Tip Material | Grip Style | Each | Each | ||
Straight Shape with Angled Nozzle | |||||||||||||
Lever Control | |||||||||||||
| 4 1/4" | 12 cfm @ 100 psi | Not Rated | 150 | 1/4 | NPT | Female | Zinc | Rubber | Plain | 0000000 | 000000 | 0000000 | 00000 |
Pistol Shape with Angled Nozzle | |||||||||||||
Lever Control | |||||||||||||
| 4 1/2" | 16 cfm @ 100 psi | Not Rated | 90 | 1/4 | NPT | Female | Plastic | Rubber | Plain | 00000000 | 00000 | 000000 | 00 |
Dual Air-Inlet Blowguns
Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses. Pull the trigger to adjust the airflow rate from a puff to a blast. The angled nozzle can direct air over and around obstacles. Blowgun conforms to OSHA 29 CFR 1910.242 requirements for maximum air outlet pressure.
Air Inlet | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Nozzle Lg. | Air Consumption | Volume | Max. Inlet Pressure, psi | Pipe Size | Thread Type | Gender | Body Material | Nozzle Tip Material | Specifications Met | Each | |
Pistol | |||||||||||
| 4" | 13 cfm @ 100 psi | 83 dBA | 145 | 1/4 | NPT | Female | Plastic | 316 Stainless Steel | OSHA Compliant 29 CFR 1910.242 | 0000000 | 0000000 |
Inline Blowguns
Operate a blowgun without disconnecting your air tool—this gun fits between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder. Press the button on the gun to activate airflow. It conforms to OSHA 29 CFR 1910.242 requirements for maximum air outlet pressure.
Air Inlet | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Nozzle Lg. | Air Consumption | Volume | Max. Inlet Pressure, psi | Pipe Size | Thread Type | Gender | Body Material | Nozzle Tip Material | Specifications Met | Each | |
Straight | |||||||||||
| 7/8" | 10 cfm @ 100 psi | Not Rated | 150 | 1/4 | NPT | Female | Chrome-Plated Zinc | Brass | OSHA Compliant 29 CFR 1910.242 | 000000 | 000000 |
Extended-Reach Blowguns with Nonmarring Tip
These blowguns include a rubber tip that won't damage your workpiece. The extra length lets you access hard-to-reach areas.
Blowguns with angled nozzle can direct air over and around obstacles. They must be used with the included brass nozzle tip to meet OSHA 29 CFR 1910.242 and conform to requirements for maximum air outlet pressure.
Air Inlet | OSHA Nozzle Tip | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Nozzle Lg. | Air Consumption | Volume | Airflow Control | Max. Inlet Pressure, psi | Pipe Size | Thread Type | Gender | Body Material | Number of Nozzle Tips Included | Nonmarring Nozzle Tip Material | Material | Specifications Met | Each | |
With Angled Nozzle | ||||||||||||||
| 24" | 11 cfm @ 100 psi | Not Rated | Lever | 120 | 1/4 | NPT | Female | Zinc | 2 | Rubber | Brass | OSHA Compliant 29 CFR 1910.242 | 0000000 | 000000 |
| 48" | 11 cfm @ 100 psi | Not Rated | Lever | 120 | 1/4 | NPT | Female | Zinc | 2 | Rubber | Brass | OSHA Compliant 29 CFR 1910.242 | 0000000 | 00000 |
Chip-Guard Extended-Reach Blowguns
Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris. Their extra length helps you access hard-to-reach areas too. All conform to OSHA 29 CFR 1910.242 requirements for maximum air outlet pressure.
Blowguns with an angled nozzle direct air over and around obstacles.
For technical drawings and 3-D models, click on a part number.
Blowguns | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Air Inlet | Repl. Nozzles | ||||||||||||
| Nozzle Lg. | Air Consumption | Volume | Max. Inlet Pressure, psi | Pipe Size | Thread Type | Gender | Body Material | Nozzle Tip Material | Specifications Met | Each | Each | ||
With Angled Nozzle | |||||||||||||
| 7" | 35 cfm @ 100 psi | 103 dB | 120 | 1/4 | NPT | Female | Aluminum | Polyethylene Plastic | OSHA Compliant 29 CFR 1910.242 | 0000000 | 000000 | 0000000 | 00000 |
| 13" | 35 cfm @ 100 psi | 103 dB | 120 | 1/4 | NPT | Female | Aluminum | Polyethylene Plastic | OSHA Compliant 29 CFR 1910.242 | 0000000 | 00000 | 000000 | 0000 |
| 19" | 35 cfm @ 100 psi | 103 dB | 120 | 1/4 | NPT | Female | Aluminum | Polyethylene Plastic | OSHA Compliant 29 CFR 1910.242 | 0000000 | 00000 | 0000000 | 00000 |
| Valve Seal Repair Kit for Blowguns with Angled Nozzle | 0000000 | Each | 00000 |
Blow-and-Spray Blowguns
Also known as a siphon gun, this blowgun sprays air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.
Blowguns that conform to OSHA 29 CFR 1910.242 meet requirements for maximum air outlet pressure.
Note: Do not use with flammable liquids.
Air Inlet | Hose | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Nozzle Lg. | Air Consumption | Volume | Max. Inlet Pressure, psi | Pipe Size | Thread Type | Gender | Maximum Flow Rate | Liquid Inlet Gender | For Liquid Inlet Hose ID | Body Material | Nozzle Tip Material | ID | Lg., ft. | Specifications Met | Each | |
Straight with Angled Nozzle | ||||||||||||||||
| 16 1/2" | 10 cfm @ 100 psi | Not Rated | 225 | 1/4 | NPT | Female | Not Rated | Male | 1/4" | Aluminum | Aluminum | 1/4" | 5 | OSHA Compliant 29 CFR 1910.242 | 0000000 | 000000 |
| 24" | 11 cfm @ 100 psi | Not Rated | 150 | 1/4 | NPT | Female | Not Rated | Male | 1/4" | Zinc | Aluminum | 1/4" | 1 | __ | 0000000 | 00000 |
| 48" | 11 cfm @ 100 psi | Not Rated | 150 | 1/4 | NPT | Female | Not Rated | Male | 1/4" | Zinc | Aluminum | 1/4" | 15 | __ | 0000000 | 00000 |