We will reply to your message within an hour.
These nozzles handle coolant pressure up to 150 psi.
The most versatile of our machine-mount coolant nozzles, these adjust from a fine mist to a direct stream and can deliver coolant in any direction. Max. pressure is 100 psi.
For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.
For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.
Press these nozzles into unthreaded holes.
Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.
Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.
Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.
This hose is made of steel.
Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.
Move grease-dispensing guns in any direction without kinking the outlet hose.
Dispense from grease guns into grease fittings and bare lubrication points.
Lubricate standard grease fittings in hard-to-reach areas. Extensions have a quick-disconnect fitting that snaps into your dispensing tip for standard grease fittings.
These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.
These flexible nozzles have threads on both ends for connecting a grease gun to a dispensing tip.
Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.
Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.
These flexible nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.
Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.
The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.
The magnetic base mounts to your work surface and has a control valve for adjusting airflow.
Choose a base, hose, and nozzle for a custom setup.
Control consumption and noise by adjusting the airflow.
Extend these telescoping nozzles to increase your reach.
Adjust airflow to control consumption and noise.
Attach one of these swivels to an air nozzle to direct air 30° left, right, up, and down.
Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.
Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.
Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Increase your reach with the telescoping nozzle.
Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.
No need to juggle multiple nozzles with different spray angles—just turn the cover to adjust the spray angle from 0° to 80°.
Push the nozzle out for lower pressures and pull it back for higher pressures. Turn the cover to adjust the spray angle from 0° to 25° or 75°.
No need to switch between nozzles—push these nozzles in and pull them out to change their pressure level, and twist their cover to adjust the spray angle between 0° and 40°. Their quick-disconnect hose connection makes attaching and removing them easy.
Instead of swapping between nozzles, turn the cover on these nozzles to change their spray angle. They have quick-disconnect couplings for easy detachment.
Twist the barrel to adjust water flow.
Slide the barbed end of these swivels into your dispensing hose and connect with a clamp. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.
Connect these swivels to the threaded end of your dispensing hose. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.
Provide a connection for hose cocks, needle valves, and nozzles by attaching these flanges and turrets to your supply pipe.
For light duty spray-down applications, attach these wash guns to any standard garden hose.
These durable wash guns are typically used for frequent washdowns and cleanup.
Remove worn fittings and repair threaded holes.
Kits include one vortex tube for converting compressed air into a stream of cold air as well as airflow adjusters, a cold-air muffler, a tube fitting, and tubing.