About Sealant Flexibility
More
About Structural Adhesives
More
Reusable Adhesive Putty
![](/prerenderstable/mvPRE/contents/gfx/imagecache/757/7576a2p2-b05@halfx_637046061721059466.png?ver=imagenotfound)
Pull off a small piece of putty and stick lightweight objects to your surface. It removes without leaving stains or residue on most surfaces and is reusable.
Container | |||||||
---|---|---|---|---|---|---|---|
Net Weight, oz. | Type | Consistency | Temp. Range, °F | Color | For Joining | Each | |
1 | Strip | Putty | 70° to 100° | Blue | Ceramic, Glass, Masonry, Metal, Wood | 000000 | 00000 |
Optically Clear Reusable Adhesive Gel
![](/prerenderstable/mvPRE/contents/gfx/imagecache/233/2334n11p1-b05-digital@halfx_637046345475820514.png?ver=imagenotfound)
Temporarily stabilize objects on flat surfaces with this clear adhesive gel. It removes cleanly from most surfaces with a twist, and it won't dry out so it can be used again.
Container | |||||||
---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Reaches Full Strength | Temp. Range, °F | Color | For Joining | Each | |
4 | Jar | 60 min. | -20° to 220° | Clear | Ceramic, Composites, Glass, Masonry, Metal, Rubber | 0000000 | 000000 |
Metal-Reinforced Epoxy Structural Adhesives
![](/prerenderstable/mvPRE/contents/gfx/imagecache/b05/b05-generic-stick3-digital@halfx_637048229168048676.png?ver=imagenotfound)
These machinable epoxies are mixed with steel, but won’t rust, so they can be used to repair cracks and threaded holes. The strongest and most weather- and chemical-resistant structural adhesives, epoxies work especially well on metals. Slice off your required amount, then knead it together to form a moldable adhesive.
Mfr. Model | Container | Strength | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Name | No. | Net Weight, oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
SteelStik | 8267 | 2 | Stick | 5 min. | 60 min. | 900 | Not Rated | Not Rated | -20° to 300° | Gray | Metal, Rubber, Composites, Masonry | 000000 | 00000 |
Waterproof Epoxy Structural Adhesives
Even when used under water, these adhesives maintain their strength. The most weather- and chemical-resistant structural adhesives, epoxies tend to work especially well on metals.
The size listed is the combined total of the two parts. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.
WaterWeld and 11801, as well as one-time-use packets, can be applied to wet surfaces or under water.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/b05/b05-generic-stick3-digital@halfx_637048229168048676.png?ver=imagenotfound)
Mfr. Model | Container | Strength | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Name | No. | Net Weight, oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Consistency (Viscosity) | Temp. Range, °F | Color | Environment | For Joining | Each | |
WaterWeld | 8277 | 2 | Stick | 25 min. | 60 min. | 900 | Not Rated | Putty (Not Rated) | Not Rated to 300° | Off-White | Salt Spray, Submersible | Metal, Plastic, Rubber, Composites | 0000000 | 00000 |
![](/prerenderstable/mvPRE/contents/gfx/imagecache/760/7605a211-@halfx_637819164870383883.png?ver=imagenotfound)
Container | Strength | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Mix Ratio | Consistency (Viscosity) | Temp. Range, °F | Color | Environment | For Joining | Each | |
11801 | 16 | Pail | 45 min. | 24 hrs. | 2,600 | 1:1 | Putty | 40° to 250° | Gray | Submersible | Metal, Plastic, Composites | 00000000 | 0000000 |
Epoxy Structural Adhesives
Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. They work especially well on metals. For putty adhesives, slice off the required amount, then knead it together to form a moldable adhesive.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/b05/b05-generic-stick3-digital@halfx_637048229168048676.png?ver=imagenotfound)
Mfr. Model | Container | Strength | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Name | No. | Net Weight, oz. | Type | Begins to Harden | Reaches Full Strength | Shear, lbs./sq. in. | Peel | Consistency (Viscosity) | Temp. Range, °F | Color | For Joining | Each | |
HighHeat | 8297 | 2 | Stick | 60 min. | 8 hrs. | 900 | Not Rated | Putty (Not Rated) | -20° to 450° | Gray | Metal, Plastic, Rubber, Composites, Masonry | 000000 | 000000 |
PlasticWeld | 8237 | 2 | Stick | 20 min. | 24 hrs. | 900 | Not Rated | Putty (Not Rated) | -20° to 300° | Off-White | Plastic, Rubber, Composites, Masonry | 000000 | 0000 |
Non-Hardening Caulk
Also known as thumb-grade caulk, this forms a non-hardening, moisture-resistant seal that remains pliable.
Butyl rubber has a sticky, gummy consistency.
Butyl mastic has a clay-like consistency.
![](/prerenderstable/mvPRE/contents/gfx/imagecache/940/9408t22p1-b05-digital@halfx_636961268290580140.png?ver=imagenotfound)
Black | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Wd. | Thick. | Lg., ft. | Tensile Strength | Hardness | Temp. Range, °F | For Joining | Number of Pieces | Each | |
08578 | 5/16" | 5/16" | 1 | Not Rated | Not Rated | -20° to 200° | Metal Plastic Asphalt Composites Glass Masonry Wood | 60 | 0000000 | 000000 |
5354 | 1/4" | 1/8" | 50 | Not Rated | Medium Hard (Durometer 60A) | -50° to 190° | Metal Metal to Plastic Metal to Glass Plastic Plastic to Glass Glass Wood Wood to Glass | 1 | 0000000 | 00000 |
5354 | 1/4" | 1/4" | 25 | Not Rated | Medium Hard (Durometer 60A) | -50° to 190° | Metal Metal to Plastic Metal to Glass Plastic Plastic to Glass Glass Wood Wood to Glass | 1 | 00000000 | 00000 |
5354 | 3/8" | 1/8" | 50 | Not Rated | Medium Hard (Durometer 60A) | -50° to 190° | Metal Metal to Plastic Metal to Glass Plastic Plastic to Glass Glass Wood Wood to Glass | 1 | 0000000 | 00000 |
5354 | 3/4" | 1/8" | 50 | Not Rated | Medium Hard (Durometer 60A) | -50° to 190° | Metal Metal to Plastic Metal to Glass Plastic Plastic to Glass Glass Wood Wood to Glass | 1 | 0000000 | 000000 |
![](/prerenderstable/mvPRE/contents/gfx/imagecache/940/9408t15-@halfx_1706044100.png?ver=imagenotfound)
White | ||||||||
---|---|---|---|---|---|---|---|---|
Dia. | Lg., ft. | Tensile Strength | Hardness | Temp. Range, °F | For Joining | Number of Pieces | Each | |
3/8" | 25 | Not Rated | Soft (Durometer 20A) | -20° to 350° | Metal Metal to Plastic Metal to Rubber Metal to Glass Plastic Plastic to Rubber Plastic to Glass Rubber Rubber to Glass Glass Masonry Wood Wood to Glass | 3 | 0000000 | 000000 |
![](/prerenderstable/mvPRE/contents/gfx/imagecache/940/9408t17p1-b05@halfx_636969706228266223.png?ver=imagenotfound)
Dia. | Lg., ft. | Tensile Strength | Hardness | Temp. Range, °F | For Joining | Number of Pieces | Each | |
Brown | ||||||||
---|---|---|---|---|---|---|---|---|
1/8" | 45 | Not Rated | Not Rated | -30° to 150° | Metal Metal to Plastic Metal to Rubber Metal to Glass Plastic Plastic to Rubber Plastic to Glass Rubber Rubber to Glass Glass Masonry Wood | 8 | 00000000 | 00000 |
1/8" | 90 | Not Rated | Not Rated | -30° to 150° | Metal Metal to Plastic Metal to Rubber Metal to Glass Plastic Plastic to Rubber Plastic to Glass Rubber Rubber to Glass Glass Masonry Wood | 8 | 00000000 | 0000 |
Gray | ||||||||
1/8" | 30 | Not Rated | Not Rated | -30° to 150° | Metal Metal to Plastic Metal to Rubber Metal to Glass Plastic Plastic to Rubber Plastic to Glass Rubber Rubber to Glass Glass Masonry Wood | 8 | 00000000 | 0000 |
1/8" | 45 | Not Rated | Not Rated | -30° to 150° | Metal Metal to Plastic Metal to Rubber Metal to Glass Plastic Plastic to Rubber Plastic to Glass Rubber Rubber to Glass Glass Masonry Wood | 8 | 0000000 | 0000 |
1/8" | 90 | Not Rated | Not Rated | -30° to 150° | Metal Metal to Plastic Metal to Rubber Metal to Glass Plastic Plastic to Rubber Plastic to Glass Rubber Rubber to Glass Glass Masonry Wood | 8 | 0000000 | 0000 |
Surface Fillers for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/g01/g01e-global-twopart-can-surfacefiller2-digital@halfx_636960132848133298.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/g01/g01e-global-twopart-can-largesmall-digital@halfx_636960127405261798.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/glo/global-twopart-pailcan-digital@halfx_636900030429438025.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/661/6617a21p1-b05-digital@halfx_636900017520120230.png?ver=imagenotfound)
Mix these two-part surface fillers together to repair leaks and cracks as well as to rebuild rough spots in metal. The size listed is the combined total of the two parts.
Loctite® Fixmaster Aluminum Liquid and Loctite® Fixmaster Aluminum Putty form a nonrusting finish.
Loctite EA 3471 and PC2 35642 have stronger adhesion than any other surface fillers we offer.
Devcon Plastic Steel surface fillers can repair areas where brazing and welding is impractical.
NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
Container | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Specifications Met | Finishing Method | For Use On | Each | |
Loctite® Fixmaster Aluminum Putty | ||||||||||||||
PC 7254 | 1 lbs. | Jar | 20 | 24 | Paste | 4:1 | 70 sq. in. @ 1/4" | -20° to 200° | Gray | __ | Machine, Drill, Tap | Aluminum | 0000000 | 0000000 |
Loctite® Fixmaster Steel Putty | ||||||||||||||
EA 3471 | 1 lbs. | Jar | 30 | 24 | Thick Liquid | 2.5:1 | 40 sq. in. @ 1/4" | -20° to 220° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 00000 |
EA 3473 | 1 lbs. | Jar | 3 | 24 | Paste | 1:1 | 50 sq. in. @ 1/4" | -20° to 190° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 00000 |
PC 235642 | 4 lbs. | Can | 30 | 24 | Paste | 2.5:1 | 170 sq. in. @ 1/4" | -20° to 220° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
Loctite® Fixmaster Stainless Steel Putty | ||||||||||||||
EA 3476 | 1 lbs. | Jar | 20 | 24 | Paste | 4:1 | 30 sq. in. @ 1/4" | -20° to 220° | Gray | __ | Machine, Drill, Tap | Bronze, Copper, Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
Devcon Plastic Steel® Putty | ||||||||||||||
10110 | 1 lbs. | Jar, Can | 45 | 16 | Putty | 9:1 | 40 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 00000 |
10120 | 4 lbs. | Jar, Can | 45 | 16 | Putty | 9:1 | 190 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 000000 |
10130 | 25 lbs. | Pail, Can | 45 | 16 | Putty | 9:1 | 1200 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 00000000 |
Devcon Plastic Steel® 5 Minute Putty | ||||||||||||||
10240 | 1 lbs. | Jar, Can | 5 | 16 | Putty | 1.7:1 | 40 sq. in. @ 1/4" | -40° to 200° | Dark Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Copper, Stainless Steel, Cast Iron | 00000000 | 000000 |
Devcon Bronze Putty | ||||||||||||||
10260 | 1 lbs. | Jar, Can | 35 | 16 | Putty | 9:1 | 50 sq. in. @ 1/4" | -40° to 250° | Bronze | __ | Machine, Drill, Sand, Saw, Tap | Brass, Bronze | 00000000 | 000000 |
Devcon Stainless Steel Putty | ||||||||||||||
10270 | 1 lbs. | Jar, Can | 60 | 16 | Putty | 11:1 | 50 sq. in. @ 1/4" | -40° to 250° | Dark Gray | NSF/ANSI 61 | Machine, Drill, Sand, Saw, Tap | Stainless Steel | 00000000 | 000000 |
Devcon FasMetal™ Putty | ||||||||||||||
10780 | 0.75 lbs. | Jar, Can | 4 | 16 | Putty | 1:1 | 60 sq. in. @ 1/4" | -40° to 250° | Gray | __ | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Titanium | 00000000 | 000000 |
Surface Fillers | ||||||||||||||
__ | 4 oz. | Stick | 3 | 24 | Putty | __ | 16 sq. in. @ 1/4" | -40° to 250° | Copper | NSF/ANSI 61 | Drill, Sand, Saw | Brass, Bronze, Copper | 0000000 | 00000 |
__ | 4 oz. | Stick | 3 | 24 | Putty | __ | 16 sq. in. @ 1/4" | -40° to 250° | Dark Gray | NSF/ANSI 61 | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
__ | 16 oz. | Stick | 45 | 24 | Putty | __ | 64 sq. in. @ 1/4" | -40° to 250° | Off-White | __ | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
Chemical-Resistant Surface Fillers for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/g01/g01e-global-twopart-can-surfacefiller2-digital@halfx_636960132848133298.png?ver=imagenotfound)
Chemicals will not affect these two-part epoxies. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Devcon Titanium Putty | |||||||||||||||
10760 | 1 | Jar | 20 | 16 hrs. | Putty | 4.3:1 | 40 sq. in. @ 1/4" | 3/4" | Yes | -40° to 350° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Titanium | 0000000 | 0000000 |
10770 | 2 | Jar | 20 | 16 hrs. | Putty | 4.3:1 | 90 sq. in. @ 1/4" | 3/4" | Yes | -40° to 350° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Titanium | 00000000 | 000000 |
High-Temperature Surface Fillers for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/140/1404k24p1-g02a-digital@halfx_636900029465449798.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/661/6617a21p1-b05-digital@halfx_636900017520120230.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/753/75325a1p1-b05-digital@halfx_636900444240154466.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/753/75325a2p1-b05-digital@halfx_636899996004509307.png?ver=imagenotfound)
Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F. Fillers that have a mix ratio are multi-part fillers. The size listed is the combined total of the parts.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
Surface fillers in a syringe come with everything you need to make repairs.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Net Weight, oz. | Type | Begins to Harden | Reaches Full Strength, hrs. | Heating Requirements to Reach Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Fixmaster 2000° Putty | |||||||||||||||
MR 2000 | 8 | __ | Can | 30 min. | 7 | __ | Putty | __ | 30 sq. in. @ 1/4" | Not Rated to 2000° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 0000000 |
Surface Fillers | |||||||||||||||
__ | __ | 4 | Stick | 90 min. | 72 | __ | Putty | __ | 16 sq. in. @ 1/4" | -40° to 450° | Gold | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 00000 |
__ | 1.5 | __ | Syringe | 20 min. | 24 | __ | Putty | 9.1:1 | 1 sq. in. @ 1/4" | -40° to 500° | Gray | Machine, Drill, Saw | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass | 0000000 | 00000 |
__ | 8 | __ | Can | 5 hrs. | 6 | 2 hrs. air dry then 4 hrs. @ 200° F | Putty | __ | 32 sq. in. @ 1/4" | Not Rated to 2000° | Dark Gray | Sand | Steel, Stainless Steel, Cast Iron | 0000000 | 00000 |
__ | 12 | __ | Can, Bottle | 2 hrs. | 6 | 4 hrs. air dry then 2 hrs. @ 160° F | Putty | 2:1 | 48 sq. in. @ 1/4" | Not Rated to 1400° | Light Gray | Sand | Aluminum | 0000000 | 00000 |
__ | 16 | __ | Can, Bottle | 20 min. | 24 | __ | Putty | 9.1:1 | 10 sq. in. @ 1/4" | Not Rated to 500° | Gray | Machine, Drill, Saw | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass | 0000000 | 00000 |
__ | 16 | __ | Bottle | 5 hrs. | 6 | 2 hrs. air dry then 4 hrs. @ 200° F | Putty | __ | 65 sq. in. @ 1/4" | Not Rated to 2000° | Dark Gray | Sand | Steel, Stainless Steel, Cast Iron | 0000000 | 000000 |
__ | 24 | __ | Can | 2 hrs. | 6 | 4 hrs. air dry then 2 hrs. @ 160° F | Putty | 2:1 | 96 sq. in. @ 1/4" | Not Rated to 1400° | Light Gray | Sand | Aluminum | 0000000 | 000000 |
Fine-Particle Abrasion-Resistant Surface Fillers for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/g01/g01e-global-twopart-can-surfacefiller2-digital@halfx_636960132848133298.png?ver=imagenotfound)
For use in processing equipment that carries particles smaller than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings. The size listed is the combined total of the two parts.
Certificates with a traceable lot number and product shelf life are available for these products. Download certificates from ORDER HISTORY after your order ships.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, lbs. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Loctite® Fixmaster Wear Resistant Putty | |||||||||||||||
PC 7222 | 1 | Jar | 30 | 24 | Putty | 2:1 | 50 sq. in. @ 1/4" | 1" | Yes | -20° to 220° | Gray | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 0000000 |
Leak-Repair Sticks for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/758/7582a44-@halfx_637001818698257486.png?ver=imagenotfound)
To stop leaks in metal tanks and equipment without draining the contents, rub the smaller stick into the leak until it stops. Then, cut the desired amount from the larger stick, knead to a uniform color to mix, and press into place. The size listed is the combined total of the two parts.
Container Net Weight, oz. | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | For Use On | Each | |
5.25 | 2 | 24 | Putty | 1:1 | 1/8" | Yes | -40° to 220° | Gray | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 0000000 | 000000 |
High-Pressure Leak-Repair Sticks for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/770/7703a1p1-g01e-digital@halfx_636916891012918423.png?ver=imagenotfound)
To stop leaks in metal tanks and equipment without draining the contents, heat the area with a heat gun or torch to melt the stick and form a permanent seal. The resulting patch can withstand pressure up to 600 psi. These sticks meet NSF/ANSI 61 safety standards for use with drinking water systems.
Container Net Weight, oz. | Begins to Harden, min. | Reaches Full Strength, sec. | Temp. to Begin to Harden, °F | Consistency | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Specifications Met | Finishing Method | For Use On | Each | |
0.375 | 1 | 90 | 250 | Putty | 1/8" | Yes | Not Rated to 350° | Green | NSF/ANSI 61 | Sand | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
Temporary Leak-Repair Sticks for Metal
![](/prerenderstable/mvPRE/contents/gfx/imagecache/770/7703a1p1-g01e-digital@halfx_636916891012918423.png?ver=imagenotfound)
Stop leaks in metal tanks and equipment without draining the contents. Until a permanent repair can be made, rub these sticks into the leak to form a temporary seal.
Container Net Weight, oz. | Begins to Harden, hrs. | Reaches Full Strength, hrs. | Formulation | Consistency | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | For Use On | Each | |
1.25 | 12 | 24 | Drying Oil | Putty | 1/8" | Yes | -50° F to 220° | Gray | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium | 000000 | 000000 |
Light-Activated Surface Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/734/73475a12-g01e@halfx_637165856222094508.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/734/73475a14-@halfx_637515743766219390.png?ver=imagenotfound)
Press these putty surface fillers in place to fill in holes, cracks, and dents. When exposed to sunlight or a UV lamp, they begin to harden immediately.
Epoxy fillers provide better adhesion and more corrosion resistance than polyester fillers.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Formulation | Size, fl. oz. | Type | Begins to Harden, sec. | Reaches Full Strength, min. | Consistency | For Max. Crack Wd. | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Polyester | 3.5 | Tube | 1 | 3 | Putty | 1" | 24 sq. in. @ 1/4" | 1/2" | Yes | -40° to 220° | White | Drill, Sand, Tap | Aluminum, Brass, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | 00000000 | 000000 |
Epoxy | 3.5 | Bottle | 1 | 5 | Putty | 1" | 24 sq. in. @ 1/4" | 1/2" | Yes | -40° to 270° | Amber | Drill, Sand, Tap | Aluminum, Brass, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Wood | 00000000 | 00000 |
Surface Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/j05/j05-generic-largesmallcan-digital@halfx_636900006472373098.png?ver=imagenotfound)
These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.
Devcon Aluminum Liquid, Devcon Aluminum Putty, and Devcon FasMetal™ 10 HVAC Repair form a nonrusting finish.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Devcon Aluminum Putty | |||||||||||||
10610 | 1 lbs. | Jar | 60 | 16 hrs. | Putty | 9:1 | 70 sq. in. @ 1/4" | -40° to 250° | Aluminum | Machine, Drill, Sand, Saw, Tap | Aluminum, Steel, Stainless Steel, Ceramic, Concrete, Fiberglass, Wood | 00000000 | 0000000 |
10620 | 3 lbs. | Jar | 60 | 16 hrs. | Putty | 9:1 | 210 sq. in. @ 1/4" | -40° to 250° | Aluminum | Machine, Drill, Sand, Saw, Tap | Aluminum, Steel, Stainless Steel, Ceramic, Concrete, Fiberglass, Wood | 00000000 | 000000 |
High-Temperature Surface Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/755/7551a23-b05@halfx_637165859471947926.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/137/1378k36p1-g02a-digital@halfx_636900016128014070.png?ver=imagenotfound)
Able to withstand temperatures up to 2300° F, these ceramic surface fillers are often used as thermal insulation on brick, mortar, burner blocks, furnace holders, and thermocouples.
Container | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
Size | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Approximate Coverage @ Thick. | For Use Outdoors | Color | For Use On | Each | |
4 fl. oz. | Syringe | 20 | 8 | Putty | 20 sq. in. @ 1/4" | No | White | Ceramic, Masonry | 0000000 | 000000 |
11 fl. oz. | Cartridge | 20 | 8 | Putty | 60 sq. in. @ 1/4" | No | White | Ceramic, Masonry | 0000000 | 00000 |
1 gal. | Pail | 20 | 8 | Putty | 720 sq. in. @ 1/4" | No | White | Ceramic, Masonry | 0000000 | 000000 |
Water-Resistant Surface Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/661/6617a21p1-b05-digital@halfx_636900017520120230.png?ver=imagenotfound)
Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.
Putty fillers come in a stick with a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. NSF/ANSI 61 surface fillers meet safety standards for use with drinking water.
Container | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight, oz. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Approx. Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Specifications Met | Each | |
Loctite® Fixmaster Metal Magic Steel | ||||||||||||||
EA 3463 | 4 | Stick | 3 | 24 hrs. | Putty | 10 sq. in. @ 1/4" | 1" | -20° to 250° | Gray | Sand | Bronze, Copper, Steel, Stainless Steel, Cast Iron, Concrete | NSF/ANSI 61 | 0000000 | 000000 |
Loctite® Fixmaster Underwater Repair Epoxy | ||||||||||||||
EA 9490 | 4 | Stick | 15 | 60 min. | Putty | 16 sq. in. @ 1/4" | 1/4" | Not Rated to 300° | White | Machine, Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Fiberglass, Concrete, Wood | __ | 0000000 | 00000 |
Surface Fillers for Plastic
![](/prerenderstable/mvPRE/contents/gfx/imagecache/glo/global-twopart-canjar-digital@halfx_636900010195780991.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/661/6617a21p1-b05-digital@halfx_636900017520120230.png?ver=imagenotfound)
Use these two-part fillers to rebuild cracked or worn plastic surfaces. The size listed is the combined total of the two parts.
Devcon Flexane 80 Putty can be used with vinyl plastic and rubber.
Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. Use with most rigid and semi-rigid types of plastic. They meet NSF/ANSI 61 for use with drinking water.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Net Weight | Type | Begins to Harden | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Devcon Flexane 80 Putty | |||||||||||||
15820 | 1 lbs. | Can | 20 min. | 7 days | Putty | 2.6:1 | 90 sq. in. @ 1/4" | -40° to 180° | Black | Sand | Vinyl Plastic, EPDM Rubber, SBR Rubber | 00000000 | 0000000 |
Surface Fillers | |||||||||||||
__ | 4 oz. | Stick | 20 min. | 24 hrs. | Putty | __ | 16 sq. in. @ 1/4" | -40° to 250° | Off-White | Drill, Sand, Saw | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic | 0000000 | 00000 |
UV-Resistant Glass Sealants
![](/prerenderstable/mvPRE/contents/gfx/imagecache/765/7650t11p1-b05-digital@halfx_636961297160751660.png?ver=imagenotfound)
These sealants don't degrade in sunlight. Also known as glazing compounds, use these sealants to install glass in framing. They’re non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, these sealants are RTV (room-temperature vulcanizing).
Elongation and joint compression/expansion tolerance indicate flexibility. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Hardness | Temp. Range, °F | Specifications Met | For Joining | Choose a Color | Each | |
Dow Corning Silicone | |||||||||||||
791 | 10.3 | Cartridge | 15 min. | 14 days | Not Rated | -50% to 50% | Soft (Durometer 25A) | -40° to 300° | ASTM C920 Type S Grade NS Class 50 | Metal Metal to Glass | 0000000 | 000000 | |
999A | 10.3 | Cartridge | 10 min. | 7 days | Not Rated | -25% to 25% | Soft (Durometer 25A) | -75° to 350° | __ | Metal Metal to Glass | 0000000 | 0000 | |
Sika Sikaflex Silicone | |||||||||||||
295 | 10.1 | Cartridge | 60 min. | 72 hrs. | 700% | -50% to 50% | Soft (Durometer 35A) | -40° to 190° | __ | Plastic Plastic to Glass Rubber Rubber to Glass | 000000 | 00000 | |
Silicone | |||||||||||||
__ | 10.1 | Cartridge | 30 min. | 24 hrs. | 475% | -25% to 25% | Soft (Durometer 20A) | -75° to 400° | FDA Compliant 21 CFR 175.105, FDA Compliant 21 CFR 177.2600, Fed. Spec. TT-S-001543A Class A, Fed. Spec. TT-S-00230C Type II Class A, NSF/ANSI 51 | Metal Metal to Glass Plastic Plastic to Glass Rubber Rubber to Glass Composites Composites to Glass Glass Wood Wood to Glass | 0000000 | 0000 |
Glass Sealing Rope
![](/prerenderstable/mvPRE/contents/gfx/imagecache/104/1049a32-@halfx_638106896642946945.png?ver=imagenotfound)
Press this pliable rope into place to hold glass in window frames and seal leaks. It’s also known as glazing compound. The rope is non-sagging, so it won't drip from vertical and overhead surfaces. It’s good for use between dissimilar materials and in environments with wide temperature fluctuation. Remove the peel-off liner to install.
Dia. | Lg., ft. | Tensile Strength, psi | Hardness | Application Temp. Range, °F | Temp. Range, °F | For Joining | Color | Each | |
Butyl Rubber | |||||||||
---|---|---|---|---|---|---|---|---|---|
1/4" | 20 | 16 | Soft (Durometer 15A) | -5° to 120° | -40° to 180° | Metal Metal to Glass Glass Wood Wood to Glass | Gray | 0000000 | 000000 |
Glass Sealants
![](/prerenderstable/mvPRE/contents/gfx/imagecache/765/7650t11p1-b05-digital@halfx_636961297160751660.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/195/1959a31p1-b05-digital@halfx_636961298586103613.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/296/2966k58p1-g02a-digital@halfx_636961293003340322.png?ver=imagenotfound)
Also known as glazing compounds, use these sealants to install glass in aluminum, steel, and wood framing. They’re non-sagging, so they won't drip from vertical and overhead surfaces. These sealants are good for use between dissimilar materials and in environments with wide temperature fluctuation. They must be painted after hardening to stand up to UV light. For sealants that require primer for use on wood, use any oil-based wood primer.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Type | Begins to Harden | Reaches Full Strength | Tensile Strength | Hardness | Application Temp. Range, °F | Temp. Range, °F | For Joining | Primer Required For Use On | Color | Each | |
Calcium Carbonate | ||||||||||||
10.1 fl. oz. | Cartridge | 6 hrs. | 72 hrs. | Not Rated | Medium Hard (Durometer 60A) | 40° to 90° | 0° to 180° | Metal Metal to Glass Glass Wood Wood to Glass | __ | White | 0000000 | 00000 |
16 fl. oz. | Can | 7 days | 4 mo. | Not Rated | Not Rated | 40° to 90° | -20° to 160° | Metal Metal to Glass Glass Wood Wood to Glass | Wood | White | 0000000 | 00000 |
32 fl. oz. | Can | 48 hrs. | 21 days | Not Rated | Not Rated | 40° to 90° | 0° to 180° | Metal Metal to Glass Glass Wood Wood to Glass | __ | White | 0000000 | 00000 |
1 gal. | Can | 7 days | 4 mo. | Not Rated | Not Rated | 40° to 90° | -20° to 160° | Metal Metal to Glass Glass Wood Wood to Glass | Wood | White | 0000000 | 00000 |
5 gal. | Pail | 48 hrs. | __ | Not Rated | Not Rated | 40° to 110° | -10° to 120° | Metal Metal to Glass Glass Wood Wood to Glass | __ | White | 0000000 | 000000 |
Structural Glass Sealants
![](/prerenderstable/mvPRE/contents/gfx/imagecache/765/7650t11p1-b05-digital@halfx_636961297160751660.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/b05/b05-generic-sausagepack-digital@halfx_636961263104796878.png?ver=imagenotfound)
Make seals that support glass under heavy loads in equipment and buildings. These sealants are also known as glazing compounds. They’re non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, sealants are RTV (room-temperature vulcanizing).
Joint compression/expansion tolerance indicates flexibility—the higher the value is, the more joint movement a sealant can sustain.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Joint Compression/ Expansion Tolerance | Tensile Strength, psi | Hardness | Application Temp. Range, °F | Temp. Range, °F | For Joining | Choose a Color | Each | |
Dow Corning Silicone | |||||||||||||
795 | 10.3 | Cartridge | 3 hrs. | 14 days | -50% to 50% | 60 | Medium Soft (Durometer 35A) | -20° to 120° | -40° to 300° | Metal | 0000000 | 000000 | |
795 | 20 | Sausage Pack | 3 hrs. | 14 days | -50% to 50% | 60 | Medium Soft (Durometer 35A) | -20° to 120° | -40° to 300° | Metal | 0000000 | 00000 |
Surface Fillers for Porcelain
![](/prerenderstable/mvPRE/contents/gfx/imagecache/glo/global-jar-small-@halfx_637171047768308220.png?ver=imagenotfound)
Keep the surface of your porcelain fixtures looking like new.
Filler repairs large chips and cracks. Sand and finish with glaze.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Crack Wd. | Size, fl. oz. | Type | Consistency | Approximate Coverage @ Thick. | Max. Thick. | Begins to Harden, min. | Reaches Full Strength, hrs. | Temp. Range, °F | Color | For Use Outdoors | For Use On | Each | |
Filler | |||||||||||||
1" | 5 | Bottle | Putty | 1 sq. in. @ 3/4" | 1" | 15 | 48 | 0° to 150° | White | Yes | Porcelain | 0000000 | 000000 |
Wood Crack Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/140/1404k24p1-g02a-digital@halfx_636900029465449798.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/661/6617a21p1-b05-digital@halfx_636900017520120230.png?ver=imagenotfound)
Press these putty-like fillers into cracks in wood up to 1/8" wide. At full strength, they can be sanded, painted, and varnished.
Nitrocellulose fillers contain real wood fibers in a solvent base, so they look and act like wood.
Epoxy fillers come in a stick with a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Crack Wd. | Size, fl. oz. | Net Weight, oz. | Type | Consistency | Lg. | Dia. | Begins to Harden, min. | Reaches Full Strength, hrs. | Approximate Coverage @ Thick. | Max. Thick. | Color | Finishing Method | For Use Outdoors | Each | |
Nitrocellulose Fillers | |||||||||||||||
1/8" | 4 | __ | Can | Putty | __ | __ | 1 | 2 | Not Rated | Not Rated | Natural Wood | Drill, Sand, Saw, Tap | Yes | 000000 | 00000 |
1/8" | 16 | __ | Can | Putty | __ | __ | 1 | 2 | Not Rated | Not Rated | Natural Wood | Drill, Sand, Saw, Tap | Yes | 000000 | 00000 |
Epoxy Fillers | |||||||||||||||
1/8" | __ | 2.9 | Stick | Putty | 7" | 7/8" | 15 | 2 | 65 sq. in. @ 1/4" | 1/4" | Natural Wood | Drill, Sand, Saw, Tap | Yes | 0000000 | 00000 |
Concrete Surface Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/768/76805t83p1-b05-digital@halfx_636899996369675633.png?ver=imagenotfound)
Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.
Mix cement surface fillers with water. They can be used to fill holes up to 7" deep. These quick-setting fillers are ready for foot traffic in just 30 minutes. Application time, after mixing, is 7 minutes.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Net Weight | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Formulation | Consistency | Mix Ratio | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Application Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Cement | |||||||||||||||
3 lbs. | Bag | 7 | 24 | Cement | Putty | 4:1 | 1 1/2 sq. ft. @ 1/4" | 7" | Yes | 50° to 100° | Gray | Drill, Sand | Concrete, Masonry, Stone | 000000 | 000000 |
Wood Surface Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/glo/global-twopart-jar-digital@halfx_636900029123252869.png?ver=imagenotfound)
Fix damaged wood or build up and replace missing wood. These two-part fillers are nonshrinking and chemical resistant. At full strength, they can be sanded, painted, and varnished. The size listed is the combined total of the two parts.
Container | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Type | Consistency | Begins to Harden, hrs. | Reaches Full Strength, hrs. | Mixing Required | Mix Ratio | Approximate Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use Outdoors | For Use On | Each | |
12 fl. oz. | Jar | Putty | 1 | 8 | Yes | 1:1 | 85 sq. in. @ 1/4" | 3/4" | 0° to 200° | Tan | Drill, Sand, Saw, Tap | Yes | Wood | 000000 | 000000 |
2 pt. | Jar | Putty | 1 | 8 | Yes | 1:1 | 230 sq. in. @ 1/4" | 3/4" | 0° to 200° | White | Drill, Sand, Saw, Tap | Yes | Wood | 000000 | 00000 |
Concrete Leveling Compounds
![](/prerenderstable/mvPRE/contents/gfx/imagecache/137/1378k36p1-g02a-digital@halfx_636900016128014070.png?ver=imagenotfound)
Give new life to damaged and worn concrete floors. These leveling compounds also fill minor depressions and cracks. Apply with a trowel.
Cement compounds are ready for foot traffic in 3 to 4 hours. Add water and mix before applying.
Container | Application | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Net Weight, lbs. | Type | Begins to Harden, hrs. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Temp. Range, °F | Time After Mixing, min. | Finishing Method | For Use On | Color | Each | |
Cement | |||||||||||||||
20 | Pail | 3 | 24 | Putty | 5:1 | 20 sq. ft. @ 1/8" | 1 1/2" | Yes | 40° to 90° | 20-45 | Drill, Sand, Saw, Tap | Concrete | Gray | 00000000 | 000000 |
40 | Pail | 3 | 24 | Putty | 5:1 | 40 sq. ft. @ 1/8" | 1 1/2" | Yes | 40° to 90° | 20-45 | Drill, Sand, Saw, Tap | Concrete | Gray | 000000 | 00000 |
Concrete Crack Fillers
![](/prerenderstable/mvPRE/contents/gfx/imagecache/765/7650t11p1-b05-digital@halfx_636900029755665080.png?ver=imagenotfound)
![](/prerenderstable/mvPRE/contents/gfx/imagecache/661/6617a21p1-b05-digital@halfx_636900017520120230.png?ver=imagenotfound)
Fill cracks in horizontal, vertical, and overhead concrete surfaces. Surface fillers that have a mix ratio are multi-part fillers. Size listed is the combined total of the parts.
Surface fillers in a 10.1 fl. oz. cartridge can be dispensed with a standard caulk gun (sold separately). They flex as concrete expands and contracts with temperature changes. Polyurethane fillers allow for more joint movement than acrylic fillers.
Surface fillers in a 9 fl. oz. cartridge include a mixer nozzle but require a caulk gun with a 26:1 thrust ratio (sold separately). These epoxy fillers can be used underwater.
Knead surface fillers in a stick to a uniform color to mix and press them into cracks in concrete floors, stairs, and walls. They can also be used to anchor bolts.
Container | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size | Net Weight | Type | Begins to Harden | Reaches Full Strength | Consistency | Mix Ratio | For Max. Crack Wd. | Approx. Coverage @ Thick. | Max. Thick. | For Use Outdoors | Application Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Polyurethane Formulation | ||||||||||||||||
10.1 fl. oz. | __ | Cartridge | 72 hrs. | 7 days | Putty | __ | 1/2" | 24 ft. @ 1/4" | 1/2" | Yes | 40° to 120° | Gray | Sand | Concrete, Masonry, Stone, Stucco | 00000000 | 00000 |
Epoxy Formulation | ||||||||||||||||
__ | 4 oz. | Stick | 2 min. | 60 min. | Putty | __ | 1/4" | 21 ft. @ 1/4" | 1/4" | Yes | 40° to 110° | Gray | Drill, Sand, Saw, Tap | Concrete, Masonry | 0000000 | 00000 |
9 fl. oz. | __ | Cartridge | 8 min. | 3 hrs. | Putty | 1:1 | 3/4" | 20 ft. @ 1/4" | 1/2" | Yes | 40° to 90° | Gray | Drill, Sand, Saw, Tap | Concrete, Masonry, Stone | 00000000 | 00000 |