Connect quick-clamp sanitary tube fittings—also known as aseptic fittings—for a fast and easy way to access your line.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

The male pipe threads on these fittings have a sealant applied for extra protection against leaks.

A PTFE seal on the tube end of these fittings allows for an extra-strong connection in high-vibration applications.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

These fittings have the highest pressure rating of all the Yor-Lok tube fittings we offer.

Use at pressures up to 4,300 psi.

Polished to at least a 15 Ra finish on the inside, these fittings have an ultra-smooth interior surface that helps prevent contamination. They are also known as ultra-high-purity fittings.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Use these brazing rings to weld tubing to an O-ring face seal adapter.

Twist these fittings onto high-vacuum tubing to quickly make sealed, high-vacuum connections without the need for clamping, welding, or tools.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

The sleeve in these fittings is rubber instead of metal, so it cushions the tubing and absorbs vibration while creating a tight seal.

The external hex bolt on these fittings allows for easy installation in cramped spaces.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

A built-in shut-off valve stops airflow when the fittings are disconnected from tubing.

Made of nickel-plated brass, these tube fittings resist corrosion better than plain brass fittings. The male threaded ends connect to NPT, NPTF, BSPP, BSPT, and other universal threads, so you don’t have to bother matching exact thread types.

Often used in outdoor, damp, and washdown environments, these 316 stainless steel fittings will not corrode from water, salt, or chemicals. The male threaded ends mate with NPT, NPTF, BSPT, BSPP, and other universal threads, so you won’t have to worry about matching exact threads when you’re on the job.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

The threads on these fittings mate with NPT, NPTF, BSPT, and BSPP threads.

Connect air brake lines with fittings that won’t crack in sub-zero temperatures. They meet Department of Transportation FMVSS 571 safety standards, so they’re often used in commercial trucks and trailers.

Ball bearings allow these fittings to rotate 360°, even after they are tightened. They have a special seal that reduces friction to allow for continuous rotation.

An all-metal body and built-in tube support or dual seals allow these fittings to handle the highest pressure ratings of all our push-to-connect tube fittings.

Tube supports slip inside tubing to prevent the walls from collapsing.

These fittings include a nut with a built-in sleeve (ferrule), so there’s no need to remove the nut for assembly.

Made of acetal, these compression fittings are lighter in weight than metal compression fittings and won’t absorb moisture when used in wet environments.

Lighter in weight than their metal counterparts, these compression fittings are polypropylene.

Made of brass, these couplings are more durable than plastic couplings.

Also known as instant fittings, these connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Use in applications up to 150 psi.

Tube supports slip inside tubing to prevent the walls from collapsing.

Tube supports slip inside tubing to prevent the walls from collapsing.

Fittings can withstand temperatures up to 200° F.

Fittings are 316 stainless steel, which has excellent chemical resistance and is more durable than plastic.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Fittings have sharp barbs that grip push-on hose with no clamps or ferrules required. The more you pull on the fittings, the tighter the hose will grip. Use in low-pressure hydraulic applications up to 350 psi.

Create or repair D.O.T. hose assemblies in the field with just a wrench and a vise, no crimper required.

Push tubing into these orifices, and an internal ring holds them in place. They're for use with plastic and soft metal tubing.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. To withstand aggressive and corrosive solutions, they have a chemical-resistant fluoroelastomer seal and a plastic body.

Insert tubing into the push-to-connect fittings on these valves—no heat, solder, or flux required. They meet NSF/ANSI 51 for safe use with food.