These rolls are coated with aluminum oxide, which is the most common abrasive material and hard enough to sand steel and wood.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

The grit particles are block shaped and cut slowly.

The soft abrasive is good for fine hand-polishing of metal surfaces that require the smoothest finish possible after an abrasive sequence. Also known as crocus cloth.

Keep sanding sheets of various grits on hand.

The grit particles are block shaped and cut slowly to produce a polished surface on metals.

These rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

These sheets resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

Keep an assortment of sheets that prevent dust and debris from building up on the abrasive surface close at hand.

The thick, abrasive-embedded nylon mesh construction flexes to compensate for uneven pressure as you sand, producing a consistent finish.

When you need to achieve a more consistent finish, choose nylon mesh sanding rolls over paper- or cloth-backed rolls.

A cushioned layer lets you apply more even sanding pressure on your workpiece, creating finer and more consistent finishes.

Sized for tight spaces, these small pads sand flat and curved surfaces. They have a flexible foam layer that gives you more control over sanding pressure, creating finer and more consistent finishes.

These cut-to-length rolls resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding. A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface.

A layer of mesh lets sanding dust and debris escape during use, preventing material buildup on the abrasive surface. These sheets resist deterioration when used wet or with grease, chemicals, cutting fluids, and other solvents that may be present when sanding.

The mesh in these sanding pads flexes to compensate for uneven pressure as you sand, producing a consistent finish.

Create consistent finishes on stainless steel, titanium, steel, iron, and nickel.

Cut the length you need, then quickly attach, remove, and reuse.

Use these rolls to create consistent finishes on hard metals such as stainless steel, iron, and nickel.

Cut the length you need, then stick to your sanding tool. When it's time to change the sheet, peel it off.

Quickly attach, remove, and reuse these hook-and-loop sheets with pole sanders.

Quickly attach, remove, and reuse.

Quickly switch between different grits—these sanding sheets attach and detach from a compatible sanding block with hook and loop.

Dust and debris won't build up on the abrasive surface.

Sharper than silicon carbide and harder than ceramic alumina, the diamond abrasive on these sheets is ideal for sanding concrete, fiberglass, and other tough materials.

Coated with zirconia alumina to stay sharper longer.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

These discs have a long-lasting diamond abrasive.

Precision-shaped ceramic alumina discs abrade hard metals like stainless steel faster than standard ceramic alumina discs because of their sharp, outwardly pointed grit.

The outer 3/8" of these discs is extremely flexible to prevent marring or gouging your work when sanding a radius or contour.

A special fastener on the back of these discs allows you to easily swap one disc for another.

Holes allow dust removal when used with a vacuum sander.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

These discs have multiple layers of brick-shaped abrasive arranged in a pattern to create highly consistent finishes.

The abrasive flaps wrap around the outer edge of these discs to reach in and sand welds at right angles (fillet welds).

The flaps wrap around the outer edge of these discs to sand welds at right angles.

The flaps have an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

These discs have a harder abrasive than standard flap sanding discs.

The flaps have an abrasive to remove material and a lubricant that minimizes heat to reduce discoloration of the work surface.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

Set at an angle and widely spaced, the overlapping abrasive flaps reach into corners.

Replace your sanding discs less often—the backing plate on these discs can be trimmed off as the abrasive flaps wear down, allowing you to use more of the disc.

A heavy duty backing plate provides more support than standard discs for heavy material removal.

With more flaps than standard discs, these last 30-40% longer.

Attach a nylon mesh sanding pad to these blocks for improved comfort and control.