These blowguns have a metal body.

The rubber tip won't damage parts.

Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.

Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.

Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.

The extra length lets you access hard-to-reach areas.

Designed to reduce noise, these blowguns are quieter than similar standard guns.

Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.

Maximize comfort and minimize strain with these lightweight guns.

The extra length lets you access hard-to-reach areas.

The most powerful blowguns we sell, these use compressed air to clean and blow debris.

Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.

Also known as siphon guns, these spray air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.

Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.

A nonconductive plastic nozzle and tip protect against accidental contact with live electrical circuits. These blowguns are tested to 1,000 volts to meet IEC 60900.

Made from rubber, these nozzles won’t scratch or damage sensitive workpieces.

These premium nozzles are engineered for the most efficient airflow consumption.

Control consumption and noise by adjusting the airflow.

Extend these telescoping nozzles to increase your reach.

Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles.

At less than 2" long and with a wide airflow pattern, these nozzles are ideal for tight spaces where you need to distribute air over a wider area than a focused-airflow nozzle.

Adjust airflow to control consumption and noise.

Focus air with pinpoint precision.

Choose a base, hose, and nozzle for a custom setup.

Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.

Replace individual parts in a variety of Superior Pneumatic air-powered hammers.

Also known as zip guns, use these air hammers with a rivet setter and a bucking bar to install solid rivets.

Place against the back side of your rivet while hammering the head.

Replace individual parts in a variety of blind rivet tools.

Designed for durability, these tools can handle the demands of high-volume production and assembly.

These nailers fit in the palm of your hand and can be used in any position.

These nailers are suited for driving nails with small heads in finishing applications.

Compressed air does the work for you.

Drive bigger staples than you can with standard air-powered staplers.

These staplers have a smaller body and are 50% lighter than our other air-powered staplers.

Adjust air-flow for precise control and smooth material flow—these guns have a built-in pressure regulator with a control knob.

Use for cutting, chipping, scraping, and staking.

Designed for fast-hitting and light striking, these hammers allow easy chisel changes—pull back on the retainer to insert or remove the chisel.

Sets include dispensing tips for grease fittings and bare lubrication points.

Dispense from grease guns into grease fittings and bare lubrication points.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Vortex tubes convert compressed air into a stream of cold air.

UL classified for hazardous locations, these vortex tubes convert compressed air into a stream of cold air to keep electronics within enclosures from overheating while also keeping dust and other contaminants out.

These NEMA-rated vortex tube are designed to keep water out during washdowns.

Set the thermostat and these vortex tubes switch on only when needed.

Cool electronics inside enclosures while keeping out rain, snow, splashing water, and dirt.

In addition to being quieter than standard enclosure-cooling vortex tubes, these stand up to washdowns and weather. They convert compressed air into a stream of cold air to keep electronics within enclosures from overheating while also keeping dust and other contaminants out.