Rotate the handle to dispense a continuous flow of liquid.

Rotate the handle to dispense a continuous flow of liquid.

A lever handle maximizes output with each stroke for low-effort dispensing.

A 316 stainless steel housing makes these pumps resistant to coolants such as ethylene glycol.

Remove liquid from hard‐to‐reach areas with a long, flexible intake tube that extends into deep and hard‐to-access tanks.

A lever handle delivers fluid on both the forward and backward strokes for faster dispensing than other drum pumps.

Since these pumps use suction to draw liquid out of your container, they continue dispensing once you get them started.

These pumps quickly empty drum contents by moving 48 gallons of liquid per minute. Their electric motors are UL listed for use in environments with flammable gases and combustible dust.

Alter the flow rate for versatile dispensing.

Often used with ammonia, etching and cleaning solutions, and other caustics, these pumps have a nonsparking air-powered motor for applications where electricity is unavailable or dangerous.

These pumps have a motor that is rated for IEC Zone 1, Groups IIB and IIA; and IEC Zone 21, Groups IIIC, IIIB, and IIIA hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits.

A chemical- and impact-resistant PVDF housing stands up to aggressive chemicals such as methyl ethyl ketone and xylene.

Keep your circulation pump in working order by replacing broken or worn parts.

The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Use these pumps to move water and lubricating oil in boiler feed systems, cooling towers, and heat exchangers

Propel liquid higher and farther than standard high-efficiency circulation pumps. These pumps use less electricity to achieve the same flow rates as other circulation pumps.

A 316 stainless steel housing sealed with fluoroelastomer resists mild chemicals and acids, such as coolant, oil, and phosphoric acid.

These pumps have the best chemical resistance of all our circulation pumps. Instead of a shaft seal, they use magnets to turn the impeller, reducing wear and leakage.

Extend the service life of your pump by mounting it to a baseplate. These heavy duty plates minimize vibration and raise the pump off the floor, preventing damage to the motor from flooding or spills.

Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications.

With a 316 stainless steel housing and PPS gears, these pumps are often used to dispense chemicals such as ethylene glycol, isopropyl alcohol, and nitric acid. Also known as gear pumps, they produce a smooth flow of liquid.

Also known as centrifugal pumps, these send a high flow of liquid through a pipeline or a closed circuit. They're often used in heating and cooling applications, as well as for tank filling and emptying.

A neoprene diaphragm resists oil and chemicals such as isopropyl alcohol and deionized water. These pumps have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

With a 316 stainless steel housing and a PTFE diaphragm, these pumps resist a variety of acids, alkalies, and flammable liquids such as phosphoric acid, acetone, and methyl ethyl ketone (MEK). They're designed for moving large volumes of thick sludges and slurries in demanding environments.

With all PTFE wetted parts, these pumps offer the best chemical resistance of all our air-powered transfer pumps and can handle solvents and petroleum-based fluids that PVDF pumps can’t.

Also known as sprayer pumps, these provide a smooth, uniform flow for agricultural spraying, soap dispensing, and chemical transferring.

A neoprene diaphragm stands up to oil and chemicals such as isopropyl alcohol and deionized water. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

Absorb pulsation caused by air-powered transfer pumps, reducing wear and preventing damage to inline components such as regulators, sensors, and gauges.

Install these pumps right in your line and engage the lever handle to start pumping.

These pumps meter a consistent amount of liquid within ±2% of the maximum flow.

With a footprint that's only a few inches in any direction, these pumps fit into compact systems to dispense small amounts of acids, cleaning fluids, and other chemicals. They're often used in sterilization, photochemical, and water treatment systems.

Use these pumps for high-pressure output of antifreeze, hydraulic oil, and motor oil.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Measure oil as it's dispensed.

Add faucets to oil dispensing stations for increased utility.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Deliver small amounts of grease with only a light push against the lubrication point.

Prime these guns faster than standard grease guns and use them with just one hand.

Dispense small amounts of grease with one of these compact guns.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Start greasing faster than standard grease guns and continue with the high output of a lever grip.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

More portable than air-powered options, these guns operate on a rechargeable battery.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

A display allows you to monitor how much grease is dispensed.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.