For frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

To protect doors and walls, these closers have a shock-absorbing stop to damp the force of doors when they’re pushed open. Designed for frequently used doors, these last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

No need to drill new holes—these closers have a mounting plate that fits the hole patterns of most closers from Norton, LCN, Yale, Corbin Russwin, and Dorma.

When replacing door closers, these mounting plates let you match new closers to your existing hole patterns from most Corbin Russwin, Dorma, LCN, Norton, and Yale closers.

Save time and money by replacing worn or damaged arms instead of the entire closer.

Nudge your door and these openers will open it the rest of the way.

A hydraulic mechanism makes these the smoothest and quietest closers we offer for storm doors.

Mounted diagonally so one end is higher than the other, the motion of an opening door tightens the torsion spring; as it unwinds, it closes the door.

Close storm doors more smoothly than standard spring closers.

Simple and compact, these closers have an arm that rolls along gates to push them closed.

Push your door open to automatically engage the holder; pull on the door to release.

For use with doors that already have a closer, these holders keep doors open with an electromagnet. When activated by a fire alarm, the magnet shuts off and releases the door.

Open and lock your enclosure door into place so it won’t close while you’re working inside the enclosure.

Slide these wedges under the door to hold it open.

Step on the spring-operated plunger to hold your door in place; tap on the release lever to free it.

Mount one end to the frame and the other end to your door to prevent it from opening too far.

These three-way holders can be inserted under the door, over the top corner of the door, or over the hinge pin to hold a door open.

Latch your door to the floor for a secure hold.

Wire these receivers directly to your automatic overhead door openers for their power supply.

Replace existing transmitters or team a transmitter and a receiver to remotely operate your automatic overhead door openers.

Also known as jackshafts, these openers operate 24-ga. or thinner overhead doors.

Commonly used on hood and trunk lids, these simple, three-piece rods telescope from 18 1/2" to 46 3/4" to prop lids open at a variety of angles.

Manually control these standard free-moving lid supports through their full range of motion. Raise or lower the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Also known as hatch springs, these supports are commonly used on hatches and other top-opening lids. Raise the lid to extend the spring, which props the lid open—an internal cable keeps the spring from overextending. Press the center of the spring to release the hold and close the lid.

Gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

These openers are often used on older casement and awning windows.

Save time and money by replacing worn or damaged handles instead of the entire opener.

Use these hinges on lightweight screen and storm doors as well as small gates.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Springs in these hinges without holes automatically swing doors and gates closed behind you.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

Spring tension pulls the door closed when it’s open less than 10° and keeps it closed without a catch or latch.

Operate doors, vents, skylights, and overhead equipment.

Store your drums horizontally to allow gravity-flow dispensing.

Rollers inside the cabinet make contents easy to load and remove.