Mount these lasers into a chuck on your milling machine or drill press to precisely indicate the drilling point. They project either a red dot or crosshair and are best viewed indoors.

Cross-hair line lasers project two intersecting lines for aligning workpieces on tables. They’re easier to see than a dot.

Optional magnetic holders store lasers when they’re not in use.

With a sealed lens and an IP67 rating, these lasers are dust and liquid tight, so you can mount them to machines in dusty or wet areas such as labs, warehouses, or marine environments to align components.

Red lasers are best for indoor environments because they’re dimmer than green lasers.

Green lasers appear up to 10 times brighter than red lasers, so they’re easier to see outdoors, in bright indoor lighting, and from far away.

Position these lasers at the correct angle for your job with adjustable angle mounts. They allow 360° rotation.

Use magnetic mounts to attach these lasers to machines and other steel surfaces instead of drilling holes and bolting them. They hold lasers at a fixed angle, but you can combine them with adjustable angle mounts for 360° rotation.

Projecting a light that's even and bright the entire length, these lasers create a line that can be measured from end to end. They're compatible with machine-vision cameras, so they're often used as a reference point for machine inspection and robot guidance. Their green light is brighter and easier to see outdoors, in strongly lit rooms, and from farther away than red lasers. As their light travels, the diameter of their beam grows. They come with an adjustable angle mount that rotates 360°, letting you position the laser at the correct angle for your job. Rated IP67, these lasers are dust and liquid tight, so you can use them in dusty or wet areas such as labs, warehouses, or marine environments.

120V AC lasers plug into standard outlets.

12V DC lasers draw power through their wire leads. Connect these lasers to devices such as programmable logic controllers (PLCs) and timer relays to automate when they turn on and off. However, you can’t plug them into standard outlets.

Use magnetic mounts to attach these lasers to machines and other steel surfaces instead of drilling holes and bolting them. They hold lasers at a fixed angle, but you can combine them with the adjustable angle mount for 360° rotation.

Slip this laser into your pocket so it's on hand to align belts, pulleys, chain, and sprockets. Place the tool against the side of your pulley or sprocket and project the laser onto the included target to detect angular or offset misalignment. They mount magnetically, so you don’t need any fasteners to secure them. The surface of the laser is machined, so it sits flush against flat surfaces for easy and precise alignment. They’re powered by a disposable battery, so they’re portable.

Style B lasers have a threaded tip, so they’re compatible with converters that change the shape of the laser, so you can perform a variety of tasks with the same tool.

Check that your pulley, gear, or sprocket system is properly aligned. These magnetic lasers stick to equipment made of steel. Project the laser beam down your belt or chain and look to see how it hits the target—you can determine angular and offset misalignment at the same time. The target has a machined surface that sits parallel to the contact surface for precise alignment. Adjust your setup until the laser line overlaps with the reference line on the target. These lasers are portable and battery powered, so they’re easy to use in spaces without outlets.

Red lasers are best for indoor environments, since they’re dimmer than green lasers.

Green lasers appear up to 10 times brighter than red lasers, so they’re easier to see outdoors or in bright indoor lighting, as well as from far away.

Lasers with one adjustable target have a single laser line that indicates offset and angular misalignment. A mirror on the target reflects the laser back to the transmitter’s reference line to show misalignment. No need to fuss with the traditional multi-target method.

Lasers with a built-in LED flashlight provide light in dim areas.

Position these lasers directly on a flat surface. Lasers project a red dot that is best viewed indoors. Twist the knob to focus the dot so it is more precise at short distances.

Help drivers center their trucks as they dock, no matter the weather or time of day. They shoot parallel bright green lines that can be seen up to 150 ft. away, even in direct sunlight. Where painted lines are less visible from snow, rain, fallen leaves, or darkness, these lasers stay visible. The included steel enclosures protect the laser from dust, debris, and the elements. The laser shoots through a hole in the side of the enclosure. You can also use these lasers indoors.

DC lasers can be connected to a controller, such as a programmable logic controller (PLC), to automate when the lasers turn on and off.

These lasers take aligning rollers from the traditional multi-tool, multi-person job to a one-tool, one-person job. Strap the transmitter to the roller you want to match and the receiver to the roller you want to check. Instead of aligning with lots of trial and error, these tools have a horizontal beam that shows if your rollers are aligned in the same plane, and a vertical beam that shows if the rollers are evenly spaced along their length. Simply adjust the roller until the beams line up with the tools' reference points.

In addition to being easy to use, these lasers were also designed to be useful in most roller setups. The adjustable straps allow you to secure them to different roller sizes and materials. They're also compact enough to fit in tight spaces between rollers.

Red lasers are best viewed indoors, since they’re dimmer than green lasers.

Green lasers appear up to 10 times brighter than red lasers, so they’re easier to see outdoors or in bright indoor lighting, as well as from far away.

Twist the head to switch between a dot, a horizontal line, or a vertical line. These lasers project accurate level references onto walls, ceilings, and equipment. The laser is red and is best viewed indoors.

When a single point of reference is enough, use a dot. Lines give you an extended reference, so you can level several objects without moving the laser. For stability, mount these lasers to a tripod (sold separately), or attach the magnetic base to a metal surface.

Lasers with straps can also be secured to nonmagnetic surfaces.

Verify your installation is level using a single reference point. These green lasers appear up to 10 times brighter than red lasers for visibility from farther away and in brightly lit areas, including outdoors. Five bubble vials confirm level, plumb, and a specific angle. One vial is a pitch gauge, which shows slope in 1/8" increments to help check drainage. For quick and easy mounting, these levels have a magnetic base. It's strong enough to hold even on vibrating equipment.

Project accurate level references onto walls and ceilings to hang light fixtures or install pipe. These lasers have four vials to verify the level, plumb, and square reference points are accurate. Because they’re red, the lasers are best viewed indoors. They have a screw-on mount to secure to a tripod, or you can use the magnetic base to stick them to equipment for quick checks. A V-groove on the body creates stability on curved surfaces, such as pipe or conduit. They’re powered by disposable batteries, so they’re portable and easy to use when you’re not near an outlet.

Set these lasers on any surface, and they'll level themselves within about 4°. Whether you’re hanging a drop ceiling or aligning bench tops, they project accurate level references to make sure your installation will be at the right height. You can also mount them in a few different ways. They have a threaded insert to attach to a tripod (sold separately). Or use the magnetic base, which is strong enough to hold even on vibrating equipment.

Red lasers are best for indoor environments, since they’re dimmer than green lasers. Green lasers appear up to 10 times brighter than red lasers, making them easier to see outdoors or in bright indoor lighting, as well as from far away.

Lasers with 5 dots help you verify your installation is straight, level, and plumb at the same time. This prevents you from having to reposition the level frequently, so you can work faster.

Lasers with a strap mount can be secures on poles and ladders.

Project two intersecting lines to ensure equipment is level and plumb. Set these leveling lasers on any surface and they'll level themselves within about 4°. They’re often used to align bench tops in shops and labs.

Red lasers are dimmer than green lasers, so they’re best viewed indoors. Use the included tripod to position them up to 46” high.

Green lasers appear up to 10 times brighter than red lasers, so they can be used from farther distances and in brightly lit areas, including outdoors. Use the included magnetic target to make your laser beam easier to see from a distance. They have a magnetic base and can be affixed to flat surfaces when mounting holes are not available. Add a tripod to adjust the height of these lasers between 16" and 51".

No need to reposition these lasers as you work around your room—crosshairs on every surface give you all the reference points you need. They are a good choice for level, plumb, and square applications, such as aligning doors and windows on multiple walls. If you set them on a surface, they level themselves within about 4° and indicate when they are out of level. You can turn this function off when you want to make sure your crosshair is level with something other than the Earth.

Secure them to a tripod using the threaded mount or use the strong magnetic base to attach them to equipment. They come with a magnetic target, which you can mount in your space to reflect the laser beam to increase its visibility in dim conditions and at far distances.

Level equipment with confidence—in addition to a crosshair, these lasers also project plumb dots, so you know the laser is in the right spot. They’re an upgrade from a standard crosshair laser while remaining simpler than lasers with multiple crosshairs. Use these lasers to precisely install square elements, such as doors and windows. The crosshair extends along your wall, so you don’t have to reposition the laser often as you work around your room. If you set them on a surface, these lasers level themselves within about 4° and indicate when they are out of level. You can turn this function off when you want to make sure your crosshair is level with something other than the Earth.

Secure them to a tripod using the threaded mount or use the strong magnetic base to attach them to equipment. They come with a magnetic target, which you can mount in your space to reflect the laser beam to increase its visibility in dim conditions and at far distances.

Levels with two laser dots help you verify your installation is plumb with reference points above and below the tool. These red lasers are best for indoor environments, since they’re dimmer than green lasers.

Levels with five laser dots help you verify that your tool is positioned correctly in multiple dimensions with reference points above, below, behind, and to the sides of the tool without repositioning your laser. These green lasers appear up to 10 times brighter than red lasers, so they’re easier to see outdoors or in bright indoor lighting, as well as from far away.

Set these lasers on any surface and they’ll level themselves horizontally within about 4°. They emit a beam of light 360° around the base, so you won’t have to keep repositioning them as you move around a space. Use them to align machinery, install conveyors, and check if walls are plumb. Visual and audible alarms alert you when the laser is beyond its leveling range. Adjust their vertical position manually. Mount these lasers to a tripod (not included) to level at a greater range of heights.

Red lasers are best viewed indoors. They include a laser detector, which indicates the height of the laser’s beam when you can’t see it, such as in bright lighting or at long distances.

Green lasers are four times brighter than red lasers, so you can see the beam outdoors and in bright lighting. They’re also easier to spot from far away. These lasers include a magnetic target, which you can mount at the height you need to reflect the beam, making it brighter and easier to see from a distance.

Mark a dot up to 100 feet across your plant for long-range applications such as laying out conveyors and positioning ventilation systems. The single laser gives you a simple reference point to check that your installation is level. These levels are compact, portable, and have a long battery life.

Red lasers are best used indoors, since they’re dimmer than green lasers. Green lasers appear up to 20 times brighter than red lasers, so they’re visible outdoors and in bright lighting. They’re also easy to see from far away.

Add a leveling plate to steady lasers on uneven surfaces or to mount them to a tripod. These plates have three adjustable legs that stabilize the laser.

90° beam splitters convert one dot into two dots set at a 90° angle.

Dot-to-line converters change the dot into a vertical or horizontal line.

These kits include a laser, a beam splitter, and a leveling plate. Mark a dot up to 1,000 feet across your plant for long-range applications such as laying out conveyors and positioning ventilation systems. A single laser dot gives you a simple way to check that your installation is level. These levels are compact, portable, and have a long battery life. You can mount them to rotating equipment without worrying about power cords. The beam splitter converts one dot into two dots that are set at a 90° angle. Use the leveling plate to steady lasers on uneven surfaces or to mount them to a tripod. These plates have three adjustable legs that stabilize the laser.

Red lasers are best used indoors, since they’re dimmer than green lasers. Green lasers appear up to 20 times brighter than red lasers, so they’re visible outdoors and in bright lighting. They’re also easy to see from far away.

Dot-to-line converters change the dot into a vertical or horizontal line.