A former industry standard, 14½° pressure angle gears are often found on older machinery.

Worm gears use screw threads to reduce shaft speed by ratios of 10:1 and greater while transmitting motion at a right angle.

A type of miter gear where one gear is smaller than the other, bevel gears provide right-angle speed reduction at ratios ranging from 2:1 to 5:1. They’re more efficient than worm gears because they create less friction.

Made from carbon steel with spiral teeth, these gears handle heavier loads at higher speeds than bevel gears with straight teeth because their teeth stay in contact longer.

A former industry standard, 14½° pressure angle gears are often found on older machinery.

Connect two shafts at a right angle without changing shaft speed or torque.

Compared to plastic gears, metal gears are better for high-load, high-speed, and heavy duty applications.

Machine your own gears to fit the exact face width and shaft diameter required.

For a custom fit on your shaft, these sprockets can be machined to your exact specifications.

For a custom fit on your shaft, these sprockets can be machined to your exact specifications.

Made of nylon, these sprockets are lightweight, quiet, and corrosion resistant.

These sprockets have two rows of teeth for use with double-strand ANSI roller chain.

Three rows of teeth make these sprockets compatible with triple-strand ANSI roller chain.

Designed to meet ISO 606 and DIN 8187 international dimensional standards, these sprockets are for use with compatible ISO and DIN roller chain.

The double row of teeth on these sprockets are designed to fit into metric ISO double-strand roller chain.

Machine the center of these sprockets for a custom fit that matches your shaft. The teeth are sized to fit into silent-drive chain.

Transfer power in one direction with these sprockets, which spin freely in the opposite direction.

Hardened teeth give these steel sprockets increased wear resistance for a long service life.

Keep constant tension on your drive with these sprockets that press against your metric ISO roller chain to take up slack and reduce wear and vibration.

A wide hub provides these sprockets with stability under heavy loads.

Get the same sizing versatility as quick-disconnect sprockets while using less space.

Switch out the bushing to install these sprockets on shafts with different diameters—no machining necessary.

Acetal and aluminum construction makes these pulleys useful in for weight-sensitive applications.

Anodized aluminum has good corrosion resistance.

Pulleys are anodized aluminum, which is more corrosion resistant than steel.

Carry heavy loads without slippage—pulleys mount with a bushing for a more secure grip on the shaft than set screws.

Move heavy loads without slippage—pulleys mount with a bushing for a more secure grip on the shaft than set screws.

Made of aluminum, these pulleys have good corrosion resistance.

Securely carry heavy loads—these pulleys mount with a bushing for a better grip on the shaft than set screws and press-fit pulleys.

To prevent slippage while moving extra heavy loads, these pulleys mount with a bushing for a more secure grip on the shaft than set screws and press-fit pulleys.

Keep high torque drive (HTD) timing belt systems running tightly with these idler pulleys. Made with built-in, free-spinning ball bearings, they're installed on shafts or belt tensioners to remove slack from timing belts.

Mount these high torque drive (HTD) pulleys onto a hex shaft.

For higher speed or higher torque applications, these GT series timing belt pulleys provide a more precise fit than HTD pulleys. Use them where accuracy is critical, such as in storage and retrieval systems or in robotics.

These pulleys are cast iron.

Increase efficiency, vary speed, and extend the life of your drive by changing the pitch on these pulleys.

Mount these pulleys with a taper-lock bushing for a tight, wobble-free hold on your shaft.

Use these pulleys with compatible quick-disconnect bushings.

These pulleys spin freely on built-in bearings to maintain tension for reduced wear and vibration.

Also known as paper-plant pulleys, these are made of a paper-fiber composite that minimizes belt slippage and wear.

With output shaft openings on both sides, these speed reducers adapt to fit multiple configurations. Mount to a NEMA 56C motor.

Mount these speed reducers to a NEMA 56C motor.

Cut shaft speed and increase torque while transmitting motion at a 90° angle in food, pharmaceutical, and other sanitary environments.

With a sanitary design for food-processing environments, these speed reducers mount to the face of your motor—no coupler required—to slow shafts and increase torque while transmitting motion at a 90° angle.

For small machinery and tight spots, these gear boxes have 1/4" diameter and smaller shafts and a footprint of less than 2½" square.

Pair these speed reducers with NEMA stepper and servo motors. Helical gears provide exact positioning and smoother travel than our other speed reducers.

Choose these sprockets when you need to expand your Ammeraal Beltech MPB conveyor line or replace its worn sprockets.

This oil withstands the heavy loads found in gears and gear-drive systems. Use it in food-processing and preparation areas where incidental contact with food is possible.

Phosphorus additives give this oil the strength it needs for use in worm gears.

Use at pressures up to 50,000 psi.