Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. They are full port, so they do not restrict flow.

316 stainless steel valves are more corrosion resistant than bronze valves.

Valves with a grease fitting have a built-in lubrication point. Inject lubricant for smooth operation and an extended service life. You can also remove the fitting to drain excess fluid from your valve.

For technical drawings and 3-D models, click on a part number.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components. All are full port, so they do not restrict flow.

316 stainless steel valves are more corrosion resistant than bronze or steel valves.

Lockable lever handles can be fixed in place using a padlock (not included).

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

T-handles resist accidental movement when snagged or bumped.

Full-port valves do not restrict flow.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

A threaded union on these valves makes them easy to install and remove without disrupting your line. They’re a good choice for lines that require frequent maintenance or cleaning. They thread together or apart with only a turn to the union fitting, unlike other threaded on/off valves that require repositioning your pipe or valve. The union fitting slides over your pipe, and the threaded fitting sits inside. With a full port, these valves won’t restrict flow.

Made of plastic, they last longer than metal valves since the inside won’t corrode or pit. They’re also lighter in weight. PVC valves are commonly used in water lines. CPVC valves handle higher temperatures than PVC or polypropylene valves. They’re the best choice if your system connects to a heater.

Valves with a T-handle have a larger gripping surface than valves with a short lever handle, so they’re easier to turn when your hands are slippery.

For technical drawings and 3-D models, click on a part number.

Bolt these valves to ANSI flanges. Their lockable lever handle can be fixed in place using a padlock (not included). All have four mounting holes to install an actuator, so you can convert them from manual to automatic valves.

Steel valves stand up to corrosion better than cast iron valves. 316 stainless steel valves are more corrosion resistant than cast iron and steel valves.

Full-port valves do not restrict flow.Pressure class 150 valves are standard and work for most low-pressure applications.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Also known as wafer ball valves, these combine the slim body of a butterfly valve with the high flow rates of a flanged ball valve. Bolt these valves to ANSI flanges—they meet ASME standards for dimensions, material, and pressure-temperature rating. They are full port, so they do not restrict flow.

316 stainless steel valves are more corrosion resistant than steel valves.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Clean and maintain these valves without removing welded connections. To create a permanent, leak-tight connection, insert unthreaded pipe into the socket and weld. These valves have a three-piece bolted body that disassembles inline, which makes it easy to access internal components. They also have lockable handles that can be fixed in place with a padlock (not included). All are full port, so they do not restrict flow.

316 stainless steel valves resist corrosion better than steel valves.

Lever handles make it easy to see if the valve is open or closed.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

Maintenance kits (sold separately) include seats, seals, and stem packing to replace worn parts inside valves.

For technical drawings and 3-D models, click on a part number.

For quick and easy access to your line, these valves attach to pipe with a clamp (sold separately) that fits around their grooved ends. No heat or threading required. They’re also known as Victaulic valves. Made of ductile iron, these valves absorb vibration and resist cracking. They’re strong enough for systems with pressure changes and frequent starts and stops. All meet NSF/ANSI 61 for safe use with drinking water. They are full port, so they do not restrict flow. To prevent tampering, lock the handle with a padlock.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Lockable T-handles can be fixed in place using a padlock (not included) with a shackle diameter up to 1/4".

Full-port valves do not restrict flow.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

No need to remove these valves from your line to access their internal components—the three-piece bolted body comes apart. Ideal in chemical-processing applications, the seal and polypropylene body stand up to aggressive and corrosive solutions.

Valves with a lever handle give you more leverage than valves with T-handles, so you can quickly open and close them with ease. To limit access to your line, replace the handle with a locking handle (sold separately). Fix the handle in place using a padlock (not included) with a shackle diameter up to 19/64".

Valves with a fluoroelastomer seal fit snug even when surfaces are irregular, misaligned, or dirty. The seal compresses and conforms to create a tight, leakproof connection. Standard-port valves slightly restrict flow.

For technical drawings and 3-D models, click on a part number.

Streamline your installation and removal process. These valves give you the leak-tight permanent connection of a socket connect with the ease of fittings that come apart. Before you install the valve, slide the union fitting over your pipe, then insert the pipe into the socket fittings and bond with primer and cement. The union fittings allow the valve to be quickly removed where other socket-connect valves would require you to cut your pipe. A fluoroelastomer seal and plastic body withstand aggressive and corrosive solutions in chemical-processing applications. All valves have a T-handle that resists accidental movement when snagged or bumped. They are full port, so they do not restrict flow.

PVC valves are often used in mild chemical processing systems. CPVC valves resist heat better than PVC valves, so they’re a good choice for systems that connect to a heater. Lockable T-handles can be fixed in place using a padlock (not included).

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Bolt these valves to ANSI flanges—they meet ASME dimensional standards. They have a plastic body and a seal that withstand aggressive and corrosive solutions in chemical-processing applications.

Glass-filled vinyl ester valves stand up to a wide variety of harsh acids and solvents. You can rely on them for repeated use, changes in pressure and flow rate, and hot and cold conditions.

Valves with a lockable lever handle can be fixed in place with a padlock (not included). They give you more leverage than short lever handles, so you can quickly open and close the valve with minimal effort.

Standard-port valves slightly restrict flow.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Disassemble the union fittings on these valves for fast installation and removal from your pipeline. They meet NSF/ANSI 61 for use with drinking water. All have a T-handle that resists accidental movement when snagged or bumped. They are full port, so they do not restrict flow.

Lockable T-handles can be fixed in place using a padlock (not included) with a shackle diameter up to 1/4”.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI 61, which means they’re safe to use with drinking water systems. They are full port, so they do not restrict flow.

PVC valves are made of the standard material used in most drinking water systems. CPVC valves resist heat better than PVC valves, so they’re better for water systems connected to a heater.

T-handles resist accidental movement when snagged or bumped.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Ideal for lines that need frequent maintenance, these valves have union fittings that disassemble quickly for removal. To install, slide the union fitting over unthreaded pipe. Insert the pipe into the socket fitting and bond with primer and cement (both not included) to create a permanent, leak-tight connection. When you need to remove the valve, just unthread the union fitting. These valves meet NSF/ANSI 61 for use with drinking water. All have a T-handle that resists accidental movement when snagged or bumped. They are full port, so they do not restrict flow.

PVC valves are made of the standard material used in most drinking water systems. CPVC valves resist heat better than PVC valves. They’re the best choice if your system connects to a heater.

Fix lockable T-handles in place using a padlock (not included).

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.

For technical drawings and 3-D models, click on a part number.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. Any port can be used as an inlet or an outlet. Turn the handle to direct flow from the inlet port to either outlet port. Valves cannot shut off flow.

316 stainless steel valves are more corrosion resistant than carbon steel valves.

Full-port valves do not restrict flow.

Standard-port valves slightly restrict flow.

Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet.