The insulation has excellent resistance to oil, so this cable can be used near motors. Often used in automated applications, it withstands continuous motion without degrading data or signal transmission

A thick outer layer of silicone rubber insulation protects this cable from high voltages while remaining ultra flexible. It stands up to continuous motion without degrading data or signal transmission.

In addition to handling continuous movement, this cable withstands twisting up to 450° without degrading data or signal transmission. It's often used in welding robots and rotary tables.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable. It withstands continuous motion without degrading data or signal transmission.

This cable meets TC-ER crush and impact requirements for exposed runs in cable trays, so it can be used without conduit. It sends signal and data to operate, measure, or regulate automated equipment.

This cable is used in variable-frequency drive motors. It has shielding to block signal interference caused by voltage fluctuations and current spikes.

Also known as festoon cable, this flat cable fits in confined spaces such as overhead cranes and hoists. It sends signal and data to operate, measure, or regulate automated equipment.

Often used in computers, small electronics, and electronic prototyping, this cable is very flexible with small gauge wire to handle tight curves in narrow spaces.

This cable can be stretched by about 40% and return to its original length, making it useful for applications where cable is in motion. It's often sewn into garments or used with equipment that must be worn.

Often used to wire pendant switches, this cable hangs from an overhead connection. Also known as bus drop cable.

Connect low-current circuits such as intercoms and security systems to a building's electrical system in single-level facilities.

Hook up thermostats, air-conditioning units, and other low-voltage equipment.

Connect devices such as sensors, programmable logic controllers, and actuators to an automated network.

Pull and turn the knob to lock, so it's secure in applications where severe vibration is a concern. Flexible for weaving around obstructions, these ready-to-use cables operate valves, throttle controls, and HVAC damper controls from a distance.

Use the attached knob to control these flexible, ready-to-use cables. Weave them around obstructions to operate valves, throttle controls, and HVAC damper controls from a distance.

A splined core limits contact points on the cable’s liner, so the core slides back and forth smoothly and keeps the cable from twisting. Pair these cables with a knob or lever to operate valves, throttle controls, and HVAC damper controls from a distance. They're flexible for weaving around obstructions.

Similar to the brake cable on a bicycle, these cables exert pulling force so you can control components such as latches, release valves, and brakes.

Also known as socket-end swage fittings, install these ball-with-shank-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these stud-end fittings with a roller swage press for a strong, permanent hold.

Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these swivel-hook-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Feed the wire rope into the opening at the bottom of these eye-end fittings and through the body for a quick and simple installation.

Add a stud end to wire rope without having to fray the rope or use a compression tool.

Add a clevis end to wire rope without having to fray the rope or use a compression tool.

Also known as open wedge sockets, these end fittings require only a torque wrench to install.

Compress the thin shank wall with a hand tool to attach these light duty mounting-plate-end fittings. They are also known as hand swage fittings.

Keep multiple sleeves on hand in a variety of sizes.

Use these sleeves for non-lifting applications such as tethering, securing, and suspending.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.

Kits include clamps and thimbles to support a wire rope loop and prevent it from fraying. Clamps must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

Also known as heavy-pattern thimbles, these can be used to reinforce the loop of a sling.

Also known as standard-pattern thimbles, these provide better protection against fraying than light duty thimbles.

Often used as bracing and guy wires, individual strands are thick solid wire for a stiff construction.

This wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

This wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

This wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys and the stainless steel wire rope withstands outdoor and washdown applications.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

This stainless steel wire rope withstands outdoor and washdown applications. The construction of this wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

This wire rope provides a good balance of abrasion resistance and flexibility.

This braided wire has a stiff construction for use as bracing and guy wires.

This wire rope provides a good balance of abrasion resistance and flexibility.

The superior corrosion resistance of nickel-copper makes this braided wire best for use with salt water and acidic- and alkaline-based solutions.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

Not only is this phosphor bronze braided wire corrosion resistant, it inhibits sparking.

This wire rope provides a good balance of abrasion resistance and flexibility.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

This wire rope provides a good balance of abrasion resistance and flexibility.

To counteract rotation while under load, the outer strands are wound in the opposite direction of the core.

More wires per strand than other wire rope provides the flexibility required for repeat bending over drums and pulleys.

Secure a ball with shank to a flat surface.

A thimble on the inside of the loop protects the wire rope from fraying.

Create a choker loop around a supporting structure with the snap-hook end and use the loop to secure the suspended material.

Made to meet stringent military standards, the fittings on these lanyards meet MS 20668.

The swivel fork allows the lanyard to rotate freely.

Attach the 90° eye to a surface for support and use the loop to secure the suspended material.

The galvanized finish resists corrosion.

For use in washdown environments, this wire rope has better corrosion resistance than the galvanized steel wire rope.

The galvanized finish resists corrosion.

For use in washdown environments, this wire rope has better corrosion resistance than the galvanized steel wire rope.

The chain has flat links that fold back on themselves for maximum flexibility. Use the split ring on one end to hold tags and keys.

These all-plastic lanyards are an economical alternative to rope and wire rope lanyards.

Weld these stubs to parts or use them to push objects apart instead of pulling them together.

The closed body protects threads from damage and debris and has a slim profile to fit in tight spaces.

Use these turnbuckles in lifting applications with wire rope. Their closed body not only protects threads from damage and debris, but also keeps these turnbuckles slim enough to fit in tight spaces.

For use with wire rope in light duty applications, these turnbuckles have a closed body that protects threads from damage and debris.

The closed body protects threads from damage and debris and has a slim profile to fit in tight spaces.