We will reply to your message within an hour.
More
Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.
Use these filters where high water and dirt removal is needed—they have a two-layer filter element made of stainless steel wire mesh and cotton/polyester packing.
Get two stages of filtration—the first stage removes most particles and water droplets; the second captures any remaining particles and water droplets down to 5 microns.
Assembled, inspected, and packaged in a clean environment, these filters come sealed in anti-static double bags.
Use these filters to extend the service life of air-powered tools and then throw them away when you're done.
Protect small air-powered tools, such as impact wrenches, ratchet wrenches, grinders, and screwdrivers.
A polyurethane bowl provides good chemical resistance for use with synthetic compressor oils and cleaning fluids.
An automatic drain discharges up to 300 gallons per hour to handle compressed air with high moisture content.
Mount these filters to a 35 mm DIN rail with the included brackets.
The housing and bowl are 316 stainless steel to handle extremely corrosive environments such as those in semiconductor, marine, chemical, and paper industries.
Replace the filter element in your Wilkerson modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your Norgren modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your Parker modular compressed air filter to trap solid particles and water droplets.
Replace the filter element in your SMC modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your Festo modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your ARO modular compressed air filter to trap solid particles and water droplets.
Replace the filter element in your ASCO Numatics modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Also known as coalescing filters, these filter elements fit in Wilkerson modular compressed air filters to remove oil and fine particles.
Also known as coalescing filters, these filter elements fit in Norgren modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in SMC modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in ARO modular compressed air filters to remove oil and particles as small as 0.3 microns.
Also known as coalescing filters, these filter elements fit in ASCO Numatics modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in Parker modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in Festo modular compressed air filters to remove oil and particles as small as 0.01 microns.
These filter elements fit in ASCO Numatics modular two-stage compressed air filters to remove water droplets, oil, and particles as small as 0.01 microns.
Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.
Designed for use in main lines with high contamination, these filters remove oil to extend the service life of air-powered tools and equipment.
A polyurethane bowl offers good chemical resistance for use with synthetic compressor oils and aggressive cleaning agents.
Housing and bowl are 316 stainless steel to handle extremely corrosive environments and meet NACE (National Association of Corrosion Engineers) specifications.
Use these filters to extend the service life of air-powered tools and equipment and then throw them away when you're done.
Use these filters in applications where high-quality air is critical. They remove particles down to 0.003 microns, eliminating small traces of oil vapor and its associated odor.
Eliminate small traces of oil vapor and its associated odor with these filters and then throw them away when you're done.
Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.
No need to buy and service two filters—these filters have a single element that removes both large and fine particles.
Replace a damaged bowl, or change the bowl material or drain type on your Norgren modular compressed air filter.
Replace a damaged bowl, or change the bowl material or drain type on your Wilkerson modular compressed air filter.
Replace a damaged bowl, or change the bowl material or drain type on your Parker modular compressed air filter.
Replace a damaged bowl, or change the bowl material or drain type on your SMC modular compressed air filter.
Replace a damaged bowl, or change the bowl material or drain type on your ARO modular compressed air filter.
Replace a damaged bowl, or change the drain type on your Festo modular compressed air filter.
Replace a damaged bowl, or change the bowl material on your ASCO Numatics modular compressed air filter.
Generate clean air for instrumentation and applications with critical air requirements.
Housing and bowl are 304 stainless steel for good corrosion resistance in damp environments.
Often used in medical device manufacturing and food-processing facilities, these filters have a stainless steel element that can be sterilized in an autoclave.
Remove bacteria, viruses, moisture, and other particles from compressed air and gases used in food, pharmaceutical, biotech, and electronics applications.
Replace failing or lost O-rings in SMC modular compressed air filters.
Replace failing or lost O-rings in Wilkerson modular compressed air filters.
Replace failing or lost O-rings in Festo modular compressed air filters.
Replace failing or lost O-rings in ASCO Numatics modular compressed air filters.
Replace failing or lost O-rings and gaskets in Norgren modular compressed air filters.
A float-operated drain valve on these separators automatically opens when the bowl begins to fill. The first step in water removal, use one of these separators to remove the large amount of water as compressed air cools.
These separators have higher flow rates compared to our other compressed air separators. Prevent equipment damage and wear caused by moisture in your compressed air supply. The first step in water removal, use one of these separators to remove the large amount of water created as compressed air cools.
In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.
When water is condensed out of a compressed air system, it contains oil from the compressor that makes disposal difficult. These separators use two-stage filtration to reduce oil content to below 20 parts per million.
A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.
These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.
No need for thread adapters—these filter/regulators have an NPT inlet and a BSPP outlet.
Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.
A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.
Mount these filter/regulators to a 35 mm DIN rail with the included brackets.
With ±0.2 psi accuracy, these filter/regulators provide more precise control than our other compressed air filter/regulators.
A stainless steel housing and bowl allow these filter/regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.
Use a single air supply to distribute air to up to four locations. In addition to the outlet for inline connection, these manifolds have three 1/4 NPT female outlets for connection to air-powered tools and equipment.
An oil filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.
An SMC filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
An ARO filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Norgren filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A Festo filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.
A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.
With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.
No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.
Filter and lubricator in one, these filter/lubricators provide clean, lubricated compressed air to extend the service life of tools and equipment.
Use these dryer/filters to protect air-powered tools from water, oil, oil vapor, and particles, then throw them away when you're done.
With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators.
These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.
Each of these filter/dryers has two desiccant towers—one that absorbs moisture, particles, and oil in the air while the other reactivates saturated desiccant so you have an uninterrupted supply of clean, dry compressed air.
Install these dryers just before air-powered tools as final protection from water and particles and throw them away when you’re done.
These all-in-one dryer/filters eliminate the need for individual dryers, separators, and filters. They cool air through refrigeration to condense water vapor for removal.
Get clean, dry air wherever you need it. The separator, filter, and dryer mounted on these tanks clean and dry compressed air as you fill it. Once full, move the tank to your workspace on its pneumatic wheels.
Stop dust and other contaminants from entering your process and equipment. Use these filters on blowers, compressors, engines, and in hydraulic systems.
Made of polypropylene, these filters can be used in damp environments where corrosion is a concern.
Clean the air going into small blowers and air-powered equipment in tight spaces.
With a threaded connection on both ends, these filters can be installed anywhere in your pipeline to keep dust and debris out of your system.
Install these filters between your high-vacuum chamber and the inlet of your pump to remove dust, water vapor, and other contaminants from the system and protect the pump. Commonly used in vacuum-furnace and coating applications, they have a polyester filter element that traps particles as small as 5 microns.
Typically used on vacuum pumps, these filters ensure that clean air is going in and coming out of your system.
Use one of these compact filters in a tight spot, or combine up to ten for a manifold application.
These filters have a clear housing so you can monitor collecting debris without stopping flow.
Remove contaminants, moisture, and other particles from steam that will touch food and for final filtering in pharmaceutical, biotech, and electronics applications.
Remove contaminants from culinary steam—steam that sanitizes food and beverage processing equipment—with these corrosion-resistant filter housings.