About Sealant Flexibility
More
About Paint and Protective Coatings
More
Self-Leveling Oil- and Fuel-Resistant Sealants
Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.
Elongation and joint expansion/compression tolerance indicate flexibility. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint expansion/compression tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.
Sealants that cannot be sold to California exceed local regulatory limits on VOC (volatile organic compounds).
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Tensile Strength, psi | Hardness | Temp. Range, °F | For Joining | Choose a Color | Cannot Be Sold To | Each | |
Buna-N | |||||||||||||
4 | Tube | 10 min. | 24 hrs. | 1,000% | Not Rated | Not Rated | Soft (Durometer 25A) | -30° to 300° | Metal Metal to Plastic Metal to Rubber Metal to Composites Metal to Glass Plastic Plastic to Rubber Plastic to Composites Plastic to Glass Rubber Rubber to Composites Rubber to Glass Asphalt Composites Composites to Glass Glass Masonry Wood | CA | 0000000 | 00000 | |
10.3 | Cartridge | 10 min. | 24 hrs. | 600% | Not Rated | Not Rated | Soft (Durometer 30A) | -30° to 300° | Metal Metal to Plastic Metal to Rubber Metal to Composites Metal to Glass Plastic Plastic to Rubber Plastic to Composites Plastic to Glass Rubber Rubber to Composites Rubber to Glass Asphalt Composites Composites to Glass Glass Masonry Wood | CA | 0000000 | 0000 |
Self-Leveling All-Weather Application Concrete Joint Sealants
Apply these sealants on wet surfaces and in cold temperatures. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.
Sealants that begin to harden in 3 minutes are ideal for sealing pavement saw cuts made when installing buried sensing wires, also known as detector loops. You can walk or drive over the seams right away because they dry tack free within minutes.
Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain.
They cannot be sold to the listed areas due to VOC (Volatile Organic Compounds) regulations.
Container | For Max. Crack | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Hardness | Wd. | Dp. | Application Temp. Range, °F | Temp. Range, °F | For Joining | Choose a Color | Cannot Be Sold To | Each | |
Hybrid Polymer | |||||||||||||||
28 | Cartridge | 3 min. | 30 hrs. | 1,000% | Not Rated | Soft (Durometer 25A) | 1 1/2" | 3/4" | -20° to 120° | -60° to 350° | Asphalt, Concrete | CT, DC, DE, Los Angeles County, CA, MA, MD, ME, NJ, NOVA, NY, Orange County, CA, PA, RI, Riverside County, CA, San Bernardino County, CA, UT, VT | 0000000 | 000000 | |
28 | Cartridge | 45 min. | 48 hrs. | 400% | Not Rated | Soft (Durometer 25A) | 1" | 1" | 35° to 120° | -75° to 300° | Metal, Plastic, Rubber, Asphalt, Composites, Masonry, Wood | __ | 0000000 | 00000 |
All-Weather Application Concrete Joint Sealants
Apply these sealants on wet surfaces and in cold temperatures. They're non-sagging, so they won't drip from vertical and overhead surfaces.
Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.
Container | For Max. Crack | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Tensile Strength, psi | Hardness | Wd. | Dp. | Application Temp. Range, °F | Temp. Range, °F | For Joining | Choose a Color | Each | |
Polyether | |||||||||||||||
28 | Cartridge | 30 min. | 48 hrs. | 1,000% | -50% to 50% | 125 | Not Rated | 1" | 1" | 32° to 120° | -75° to 300° | Metal, Plastic, Rubber, Asphalt, Composites, Glass, Masonry, Wood | 00000000 | 000000 |
High-Strength Self-Leveling Concrete Joint Sealants
Seal concrete joints in high-traffic locations—these sealants stand up to heavy wear and tear, such as steel wheel traffic. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.
Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.
Container | For Max. Crack | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model No. | Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Mix Ratio | Elongation | Joint Compression/ Expansion Tolerance | Hardness | Wd. | Dp. | Temp. Range, °F | For Joining | Color | Each | |
Loctite® Polyurethane | |||||||||||||||
PC 6231 | 8.6 | Cartridge | 3 min. | 90 min. | 1:1 | 82% | -10% to 10% | Hard (Durometer 75A) | 3/4" | 2 1/4" | -40° to 120° | Metal, Plastic, Rubber, Asphalt, Composites, Glass, Masonry, Wood | Gray | 0000000 | 000000 |
High-Strength Concrete Joint Sealants
Seal concrete joints in high-traffic areas—these sealants stand up to heavy wear and tear, such as steel wheel traffic. They're non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone, sealants are RTV (room-temperature vulcanizing).
Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.
Container | For Max. Crack | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Hardness | Wd. | Dp. | Temp. Range, °F | For Joining | Color | Each | |
Silicone | |||||||||||||
20 | Sausage Pack | 60 min. | 7 days | 1,000% | -50% to 100% | Medium Hard (Durometer 55A) | 1" | 1/2" | -20° to 300° | Metal, Plastic, Rubber, Composites, Glass, Masonry, Wood | Gray | 000000 | 000000 |
29 | Cartridge | 60 min. | 7 days | 1,000% | -50% to 100% | Medium Hard (Durometer 55A) | 1" | 1/2" | -20° to 300° | Metal, Plastic, Rubber, Composites, Glass, Masonry, Wood | Gray | 000000 | 00000 |
Textured Concrete Joint Sealants
The textured finish matches concrete surfaces. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.
Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.
Container | For Max. Crack | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Hardness | Wd. | Dp. | Temp. Range, °F | For Joining | Color | Each | |
Hybrid Polymer | |||||||||||||
10.1 | Cartridge | 2 hrs. | 24 hrs. | 600% | -25% to 25% | Medium (Durometer 46A) | 1/2" | 3/8" | -40° to 155° | Metal, Asphalt, Composites, Masonry | Gray | 000000 | 00000 |
Self-Leveling Roof Joint Sealants
Keep out the elements by sealing roof joints. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish. They're good for use in environments with wide temperature fluctuation.
Container | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Tensile Strength | Hardness | Application Temp. Range, °F | Temp. Range, °F | For Joining | Color | Each | |
Buna-N | |||||||||||
10.3 | Cartridge | 30 min. | 3 days | Not Rated | Not Rated | 40° to 100° | Not Rated to 400° | Metal, Plastic, Rubber, Asphalt, Composites, Glass, Masonry, Wood | Aluminum | 0000000 | 000000 |
EPDM Rubber | |||||||||||
10.3 | Cartridge | 4 hrs. | 3 days | Not Rated | Not Rated | 20° to 120° | -40° to 200° | Metal, Plastic, Rubber, Asphalt, Composites, Masonry, Wood | Black | 0000000 | 00000 |
Roof Joint Sealants
Keep out the elements by sealing roof joints. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces. They are good for use in environments with wide temperature fluctuation.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Joint Compression/ Expansion Tolerance | Tensile Strength, psi | Hardness | Temp. Range, °F | For Joining | Color | Each | |
Asphalt | ||||||||||||
10.1 | Cartridge | 60 min. | 28 days | Not Rated | Not Rated | Not Rated | Not Rated | -40° to 180° | Metal, Asphalt, Composites, Masonry, Wood | Black | 0000000 | 00000 |
Buna-N | ||||||||||||
10.3 | Cartridge | 30 min. | 3 days | Not Rated | Not Rated | Not Rated | Not Rated | Not Rated to 400° | Metal, Plastic, Rubber, Asphalt, Composites, Glass, Masonry, Wood | Aluminum | 0000000 | 00000 |
All-Weather Application Roof Joint Sealants
Fix roof leaks in cold and wet conditions. These sealants can even be applied underwater. They're non-sagging, so they won't drip from vertical and overhead surfaces. They are good for use in environments with wide temperature fluctuation.
Elongation indicates flexibility—the higher the value is, the more joint movement a sealant can sustain.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden | Reaches Full Strength | Elongation | Tensile Strength, psi | Hardness | Application Temp. Range, °F | Temp. Range, °F | For Joining | Color | Each | |
Hybrid Polymer | ||||||||||||
10 | Cartridge | 30 min. | 24 hrs. | 559% | 235 | Soft (Durometer 33A) | 30° to 120° | -40° to 200° | Metal, Plastic, Rubber, Asphalt, Masonry | Black | 000000 | 000000 |
10 | Cartridge | 60 min. | 24 hrs. | 465% | 115 | Soft (Durometer 19A) | 30° to 120° | -40° to 200° | Metal, Plastic, Rubber, Asphalt, Masonry | White | 000000 | 00000 |
Water-Resistant Surface Fillers
Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.
Paste fillers resist alkalies, solvents, gasoline, and oil.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Max. Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | |||||||||||||
2 | Tube | 5 | 60 min. | Paste | 1:1 | 12 sq. in. @ 1/4" | 1/2" | Not Rated to 200° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 000000 |
2 | Jar, Bottle | 20 | 24 hrs. | Paste | 5:1 | 8 1/2 sq. in. @ 1/4" | 1 1/2" | Not Rated to 185° | White | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
2 | Jar, Bottle | 20 | 24 hrs. | Paste | 5:1 | 8 1/2 sq. in. @ 1/4" | 1 1/2" | Not Rated to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
14 | Can, Jar | 20 | 24 hrs. | Paste | 5:1 | 62 sq. in. @ 1/4" | 1 1/2" | Not Rated to 185° | White | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
14 | Can, Jar | 20 | 24 hrs. | Paste | 5:1 | 62 sq. in. @ 1/4" | 1 1/2" | Not Rated to 250° | Gray | Machine, Drill, Sand, Saw, Tap | Aluminum, Brass, Bronze, Copper, Steel, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, Polyimide Plastic, Nylon Plastic, Vinyl Plastic, EPDM Rubber, Fiberglass, Glass, Concrete, Ceramic, Porcelain, Plaster, Grout, Masonry, Asphalt, Stone, Wood | 0000000 | 00000 |
Leak-Stopping Concrete Crack Fillers
Stop slow-flowing and weeping leaks in concrete. These crack fillers begin to harden in three to five minutes to create a permanent fix that won't shrink.
Polyurethane fillers are thin to penetrate deep into cracks. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a standard caulk gun (sold separately). For especially large cracks, use a packer (sold separately) with a grease gun or a grout pump.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden, min. | Reaches Full Strength | Consistency | For Max. Crack Wd. | Approx. Coverage @ Thick. | Max. Thick. | Application Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Polyurethane | |||||||||||||
10.1 | Cartridge | 3 | 24 hrs. | Thin Liquid | 3/4" | 15 ft. @ 1/2" | 1/2" | 35° to 90° | Amber | Sand | Concrete, Ceramic, Porcelain, Grout, Masonry, Asphalt, Stone | 000000 | 000000 |
Material | For Hole Dia. | Each | |
Steel | 5/8" | 000000 | 00000 |
High-Flow Leak-Stopping Concrete Crack Fillers
Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink. When fully cured they create a seal that can withstand pressure of up to 2,000 psi. Apply with a dispensing gun (sold separately). The size listed is the combined total of the two parts. A mixer nozzle is included.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, fl. oz. | Type | Begins to Harden, sec. | Reaches Full Strength, min. | Consistency | For Max. Crack Wd. | Approx. Coverage @ Thick. | Max. Thick. | Application Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
20.2 | Cartridge | 3 | 60 | Thin Liquid | 3/4" | 5 ft. @ 1/2" | 1/2" | 35° to 90° | Amber | Drill, Sand, Saw | Concrete, Ceramic, Porcelain, Grout, Masonry, Asphalt, Stone | 000000 | 000000 |
Dispensing Gun | 000000 | Each | 000000 |
Roof Repair Mesh Fabric
Reinforce hot- and cold-applied asphalt patching compounds and coatings with this flexible fabric.
Lg., ft. | Wd. | Material | For Use Outdoors | Application Temp. Range, °F | Color | Specifications Met | For Use On | Each | |
50 | 6" | Asphalt-Coated Fiberglass Fabric | Yes | Not Rated | Black | ASTM D1668 Type I | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 000000 |
Heavy Duty Roof Patching Compounds
These patching compounds are the most flexible and watertight we offer. Developed for use on flashing, chimneys, and high-stress areas, they are highly vibration resistant.
Dispense compounds in a cartridge in a standard caulk gun (sold separately).
Compounds that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).
Container Size | Consistency | Begins to Harden, hrs. | Reaches Full Strength | Approximate Coverage @ Thick. | Max. Thick. | Application Temp. Range, °F | Color | For Use Outdoors | For Use On | Cannot Be Sold To | Each | |
Cans | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 gal. | Paste | 2 | 7 days | 8 sq. ft. @ 1/4" | 1/8" | 20° to 100° | Black | Yes | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | Los Angeles County, CA; Orange County, CA; Riverside County, CA; San Bernardino County, CA | 0000000 | 000000 |
Cartridges | ||||||||||||
10.1 fl. oz. | Gel | 12 | 24 hrs. | 1/2 sq. ft. @ 1/4" | 1/2" | 40° to 120° | Black | Yes | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | __ | 0000000 | 00000 |
Roof Patching Compounds
Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.
Apply acrylic compounds to dry surfaces. Apply asphalt compounds to wet or dry surfaces.
Container | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, gal. | Type | Consistency | Begins to Harden | Reaches Full Strength | Approximate Coverage @ Thick. | Max. Thick. | Application Temp. Range, °F | Color | Specifications Met | For Use Outdoors | For Use On | Each | |
Acrylic Compounds | |||||||||||||
1 | Can | Thick Liquid | 4 hrs. | 24 hrs. | 12 sq. ft. @ 1/8" | 1/4" | 50° to 90° | White | __ | Yes | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 00000000 | 000000 |
Asphalt Compounds | |||||||||||||
1 | Can | Thick Liquid | 60 min. | 30 days | 12 sq. ft. @ 1/8" | 1/2" | 50° to 120° | Black | ASTM D4586 | Yes | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 00000 |
4.7 | Pail | Thick Liquid | 60 min. | 30 days | 56 sq. ft. @ 1/8" | 1/2" | 50° to 120° | Black | ASTM D4586 | Yes | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 00000 |
Temporary Roof Leak Patching Compounds
Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.
Container | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Max. Crack Wd. | Net Weight, lbs. | Type | Consistency | Contains Aggregate | Approximate Coverage @ Thick. | Application Temp. Range, °F | Color | For Use Outdoors | For Use On | Each | |
1" | 25 | Pail | Powder | Yes | 40 sq. ft. @ 1/2" | 35° to 100° | Gray | Yes | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 0000000 | 000000 |
Adhesive-Back Roof Repair Rolls
Roll out a fast fix for leaky roofs and gutters with these peel-and-stick rolls. Backing is rubberized asphalt adhesive. Roll can be cut to size.
Lg., ft. | Wd. | Thick. | Material | Backing Material | Mixing Required | Application Temp. Range, °F | For Use On | Each | |
Aluminum | |||||||||
---|---|---|---|---|---|---|---|---|---|
33 1/2 | 4" | 3/64" | Aluminum | Asphalt | No | 55° to 100° | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 000000 |
33 1/2 | 6" | 3/64" | Aluminum | Asphalt | No | 55° to 100° | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 00000 |
33 1/2 | 36" | 3/64" | Aluminum | Asphalt | No | 55° to 100° | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 000000 |
White | |||||||||
33 1/2 | 4" | 3/64" | Aluminum | Asphalt | No | 55° to 100° | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 00000 |
33 1/2 | 6" | 3/64" | Aluminum | Asphalt | No | 55° to 100° | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 00000 |
33 1/2 | 36" | 3/64" | Aluminum | Asphalt | No | 55° to 100° | Aluminum, Copper, Steel, Stainless Steel, Masonry, Stone, Asphalt, Wood | 000000 | 000000 |
Asphalt Crack Fillers
These crack fillers come in an easy-to-pour jug for filling cracks in asphalt up to 1/2" wide. They’re ready for traffic in 2 to 5 days.
Container | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Size, gal. | Type | Begins to Harden, min. | Reaches Full Strength, days | Consistency | For Max. Crack Wd. | For Use Outdoors | Application Temp. Range, °F | Color | For Use On | Each | |
1 | Jug | 30 | 2 | Thick Liquid | 1/2" | Yes | 55° to 100° | Black | Asphalt | 0000000 | 000000 |
Flexible Rope Asphalt Crack Fillers
Cut rope to the length you need, pack it in cracks up to 1" wide, and heat with a propane torch (not included). Rope is self-leveling.
Container | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, gal. | Type | Lg., ft. | Begins to Harden, min. | Reaches Full Strength, min. | Consistency | For Crack Wd. | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Application Temp. Range, °F | Color | For Use On | Each | |
2 | Pail | 125 | 20 | 20 | Semi-Solid | 1/4" to 1" | 125 ft. @ 1/2" | 1/2" | Yes | 32° to 300° | Black | Asphalt | 0000000 | 000000 |
Asphalt Patching Compounds
Spread patching compounds in dry, wet, and even water-filled holes. Compress them with a tamper or shovel and they are immediately ready for traffic.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, gal. | Type | Begins to Harden, hrs. | Reaches Full Strength, days | Consistency | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Application Temp. Range, °F | Color | For Use On | Each | |
5 | Pail | 1 | 7 | Semi-Solid | 6 sq. ft. @ 1" | 2" | Yes | -20° to 140° | Black | Asphalt | 0000000 | 000000 |
55 | Drum | 1 | 7 | Semi-Solid | 70 sq. ft. @ 1" | 2" | Yes | -20° to 140° | Black | Asphalt | 0000000 | 000000 |
Grout
Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring. Apply with a grout float.
Acrylic grout does not require mixing. It resists shrinking, cracking, and staining.
Container | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, gal. | Type | Reaches Full Strength | Consistency | For Max. Crack Wd. | Approximate Coverage @ Thick. | Max. Thick. | For Use Outdoors | Application Temp. Range, °F | Color | For Use On | Each | |
Acrylic | ||||||||||||
1 | Pail | 24 hrs. | Paste | 1/2" | 101 sq. ft. @ 1/4" | 1/2" | No | 50° to 100° | Beige | Concrete, Plaster, Ceramic, Porcelain, Grout, Masonry, Asphalt, Stone | 00000000 | 000000 |
1 | Pail | 24 hrs. | Paste | 1/2" | 101 sq. ft. @ 1/4" | 1/2" | No | 50° to 100° | Gray | Concrete, Plaster, Ceramic, Porcelain, Grout, Masonry, Asphalt, Stone | 00000000 | 00000 |
1 | Pail | 24 hrs. | Paste | 1/2" | 101 sq. ft. @ 1/4" | 1/2" | No | 50° to 100° | White | Concrete, Plaster, Ceramic, Porcelain, Grout, Masonry, Asphalt, Stone | 00000000 | 00000 |
Low-Friction Epoxy Coatings
Use these coatings on tanks to create a low-friction lining that prevents bubble formation and turbulence in the liquids within. These thick coatings can also be used in chutes and on foundations for a smooth, glossy surface that resists abrasion, chemicals, and extreme temperatures once cured. Apply with a brush or roller. The size listed is the combined total of the two parts.
Dry Time | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Mfr. Model Name | Mfr. Model No. | Container Size, gal. | Composition | Touch, hrs. | O'all, hrs. | Approximate Coverage @ Thickness | Application Time After Mixing, min. | Application Temp. Range, °F | For Use On | Color (Appearance) | Each | |
Loctite® Coatings | ||||||||||||
Nordbak Chemical Resistant Coating | PC 7319 | 1 1/2 | Solvent Based | 4 | 16 | 150 sq. ft. @ 10 mil | 25 | 65° to 80° | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Galvanized Iron, Galvanized Steel, Plastic, Composites, Fiberglass, Ceramic, Glass, Masonry, Concrete, Stone, Asphalt, Drywall, Wood | Gray (Gloss) | 000000 | 0000000 |
Protective Coatings
Used to insulate, create grips, and color-code components, these coatings resist high temperatures, light abrasion, and corrosion.
Coatings in a can can be dipped, brushed, or sprayed.
Container | Dry Time | |||||||
---|---|---|---|---|---|---|---|---|
Size | Composition | Touch, min. | O'all | Approximate Coverage @ Thickness | For Use On | Color (Appearance) | Each | |
PVC Plastic—Can | ||||||||
1 gal. | Solvent Based | 30 | 24 hrs. | 60 sq. ft. @ 5 mil | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Galvanized Iron, Galvanized Steel, Plastic, Rubber, Fiberglass, Ceramic, Glass, Masonry, Concrete, Stone, Asphalt, Drywall, Wood | Black (Semi-Gloss) | 00000000 | 0000000 |
1 gal. | Solvent Based | 30 | 24 hrs. | 60 sq. ft. @ 5 mil | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Galvanized Iron, Galvanized Steel, Plastic, Rubber, Fiberglass, Ceramic, Glass, Masonry, Concrete, Stone, Asphalt, Drywall, Wood | Red (Semi-Gloss) | 00000000 | 000000 |
1 gal. | Solvent Based | 30 | 24 hrs. | 60 sq. ft. @ 5 mil | Aluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Galvanized Iron, Galvanized Steel, Plastic, Rubber, Fiberglass, Ceramic, Glass, Masonry, Concrete, Stone, Asphalt, Drywall, Wood | Yellow (Semi-Gloss) | 00000000 | 000000 |
Coatings for Roofs
Use these coatings to form a water-resistant layer to restore and reinforce your roof. Apply to a dry surface with a sprayer or brush. They cannot be sold to the listed areas because they exceed local regulatory limits on VOCs (volatile organic compounds).
Container | Dry Time | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Size, gal. | Type | Composition | Touch, hrs. | Overall, hrs. | Approx. Coverage @ Thick. | Max. Temp., °F | Application Temp. Range, °F | Specifications Met | For Use On | Color | Cannot Be Sold To | Each | |
0.9 | Can | Solvent Based | 1 | 24 | 25 sq. ft. @ 56 mil | 100° | 50° to 100° | ASTM D4479 | Asphalt | Black | CA, Canada | 0000000 | 000000 |
4.75 | Pail | Solvent Based | 1 | 24 | 135 sq. ft. @ 56 mil | 100° | 50° to 100° | ASTM D4479 | Asphalt | Black | CA, Canada | 0000000 | 000000 |
Reflective Asphalt Coatings for Roofs
These coatings reflect up to 60% of the sun's rays. They also restore and reinforce your roof by forming a water-resistant seal. Apply to a dry surface with a sprayer or brush. They cannot be sold to the listed areas due to VOC regulations.
Dry Time | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Container Size, gal. | Composition | Surface Reflectivity | Touch, hrs. | Overall, hrs. | Approx. Coverage @ Thick. | Max. Temp., °F | Application Temp. Range, °F | Specifications Met | For Use On | Color | Cannot Be Sold To | Each | |
4 3/4 | Solvent Based | 60% | 4 | 24 | 235 sq. ft. @ 24 mil | 100° | 50° to 100° | ASTM D2824 Type 3 | Steel, Iron, Asphalt, Composites | Aluminum | CA, CO, CT, DE, MD, MI, NY, OH, RI, UT, Canada | 0000000 | 0000000 |
Adhesive Removers for Concrete
These adhesive removers are safe, easy to use, and virtually odorless. They evaporate slowly, allowing them to work for up to 24 hours.
Container | |||||||||
---|---|---|---|---|---|---|---|---|---|
Type | Size | Max. Coverage, sq. ft. | Composition | Harshness | For Use On | For Removing | Primary Chemical | Each | |
Liquid | |||||||||
Spray Bottle | 32 fl. oz. | 50 | Solvent Based | Moderate | Aluminum, Asphalt, Concrete, Galvanized Steel, Stainless Steel, Steel | Adhesive | Soybean Oil (80-90%) | 0000000 | 000000 |
Jug | 1 gal. | 200 | Solvent Based | Moderate | Aluminum, Asphalt, Concrete, Galvanized Steel, Stainless Steel, Steel | Adhesive | Soybean Oil (80-90%) | 000000 | 00000 |